LG LV700N-D1 User manual

LV700N-D1
LV700P-D1

MM
9. Do not defeat the safety purpose of the polariz-9. Do not defeat the safety purpose of the polariz-
ed or grounding-type plug. A polarized plug has ed or grounding-type plug. A polarized plug has
two blades with on wider thanthe other. A grou- two blades with on wider thanthe other. A grou-
nding type plug has two blades and a third gro- nding type plug has two blades and a third gro-
unding prong. The wide blade or the third prong unding prong. The wide blade or the third prong
are provided for your safety. If the provided plug are provided for your safety. If the provided plug
does not fit into you outlet, consult an electrici- does not fit into you outlet, consult an electrici-
an for replacement of the obsolete outlet. an for replacement of the obsolete outlet.

7
8
9
10
12
13
25
Cautions for safe Operation
What’s in the box
Construction
Installation
Troubleshooting
OSD Menu
Specification

M3 Tapping Screws (4EA)
(Pan Lock Screw)
M3 Screw (1EA)
This camera must always be operated a DC 12V Certified/Listed, class 2
power supply only.

2. - Tighten the M3 Tapping Screw (A) to
fix the Ceiling Mount on the installation
label.
3. - Push the Lock Button and turn the B-
ase Deco counterclockwise simultane-
ously.
- Remove the Base Deco.
4. - Loosen the Dome Frame Lock Screw
(C).
- Remove the Dome Frame.
5. - Adjust the Tilt(Up/Down) and the Pan
(Left/Right).
6. - Install the Dome Frame.
- Tighten the Dome Frame Lock Screw
(C)
7. - Install the Base Deco.
- Turn the Base Deco clockwise.
1. - Use the installation label to check the
place that you wish to install.
Holder
OSD Board
Revolver
Service Output
FRONT
Ceiling Mount
3
Holder
Revolver
Revolver
Base
4~6
Direct Screw
FrontFront
Direct Screw
Surface Mount Cable Hole
Cut Off Celing Line
M4 Self Topping Screw
for Nount
P/N : MEZ57336601
Remove Dust On Celing
and Stick It
Dome Frame Lock Screw(C)
Dome Frame Lock Screw(B)
•
•

Connect a DC 12V power source to the Power Input Jack of the camera as
shown below.
105mm
140
96.5
① Pushing part of base arrow pointed turn the part B counter clock
simultaneously to remove the base deco.
② Roosen the lock screw to remove the dome cover
③ Widen the cover with both hands then remove the cover.
④ Adjust Near&Far, Wide&Tele as you wish Then install base deco,
screw, inner dome in reverse order.
Step2 Step3 Step4
Step1 SCREW
*If you use the video output with service output
(jack) at the same time, it may falls off the signal output
(Output)

AUTO / BW / COLOR
LENS MANUAL / DC
LENS DC
OSD MENU - LENS
LENS DC
BRIGHTNESS
: RETURN
200
Please select the type of the lens you wish to use by pressing
the LEFT or RIGHT button.
-When selecting ‘DC’ lens, the shutter speed is ‘FIXED’ mode (1/60 or 1/50)
-When selecting (MANUAL, lens, the shutter speed is ‘AUTO’)
• DC/VIDEO : Auto iris lens selection
• MANUAL : Manual lens selection
• DC mode - Brightness setting(0~255 steps)
14

LENS DC
LENS DC
15
16
•
•
•
•

LENS DC
17
18
BLC AREA Setting
ALL CLEAR
ALL SET
RETURN
Cursor : Please select area.
- Yellow color is the selected area.
- Orange color is the nonselected area.
*Press the SETUP switch long. Enter with the sub set menu.
All CLEAR : Cancel the all selected area.
ALL SET : select all the area.
RETURN : Using the ‘RETURN’ key to go back to the main menu.
11
11
22
22
33
33
44
44
•
•

LENS DC
LENS DC
19
20
•
•
•
•

LENS DC
21
22
•
•
•

LENS DC
LENS DC
23
24

LV700N-D1 LV700P-D1
Lens 2.8~12mm Vari-focal DC IRIS Lens
2000Lux (3200° K)
OSD
AUTO
COLOR/BW/AUTO
446g(With Ceiling Bracket : 90g)
Φ140(Φ140 Dome) x 105mm(Without ceiling bracket)
25

P/NO : MFL61289201