LG LW9422 series User manual

Warning
• Donotinstallthisequipmentina
confinedspacesuchasabookcaseor
similarunit.
• Wiringmethodsshallbeinaccordance
withtheNationalElectricCode,ANSI/
NFPA70.
• ThisisaclassAproduct.Inadomestic
environmentthisproductmaycause
radiointerferenceinwhichcasethe
usermayberequiredtotakeadequate
measures.
• Toreduceariskoffireorelectricshock,
donotexposethisproducttorainor
moisture.
Caution
• Thisinstallationshouldbemadebya
qualifiedservicepersonandshould
conformtoalllocalcodes.
• Toavoidelectricalshock,donotopen
thecabinet.Referservicingtoqualified
personnelonly.
• Theapparatusshallnotbeexposedto
water(drippingorsplashing)andno
objectsfilledwithliquids,suchasvases,
shallbeplacedontheapparatus.
Todisconnectpowerfrommains,pull
outthemainscordplug.Wheninstalling
theproduct,ensurethattheplugiseasily
accessible.
LGElectronicsherebydeclares
thatthis/theseproduct(s)is/are
incompliancewiththeessential
requirementsandotherrelevant
provisionsofDirective2004/108/
EC,2006/95/EC,and2009/125/EC.
EuropeanStandardsCentre:
Krijgsman1,1186DM
AmstelveenTheNetherlands
Disposal of your old appliance
1. Whenthiscrossed-out
wheeledbinsymbolis
attachedtoaproduct
itmeanstheproductis
coveredbytheEuropean
Directive2002/96/EC.
2. Allelectricalandelectronic
productsshouldbe
disposedofseparatelyfrom
themunicipalwastestream
viadesignatedcollection
facilitiesappointedbythe
governmentorthelocal
authorities.
3. Thecorrectdisposalof
youroldappliancewillhelp
preventpotentialnegative
consequencesforthe
environmentandhuman
health.
4. Formoredetailed
informationaboutdisposal
ofyouroldappliance,
pleasecontactyourcity
office,wastedisposal
serviceortheshop
whereyoupurchasedthe
product.
EEECompliancewithDirective.
(forTurkeyonly)
Important Safety Instructions
1. Readtheseinstructions.
2. Keeptheseinstructions.
3. Heedallwarnings.
4. Followallinstructions.
5. Donotusethisapparatusnearwater.
6. Cleanonlywithdrycloth.
7. Donotblockanyventilationopenings.
Installinaccordancewiththe
manufacturer’sinstructions.
8. Donotinstallnearanyheatsourcessuch
asradiators,heatregisters,stoves,orother
apparatus(includingamplifiers)that
produceheat.
9. Donotdefeatthesafetypurposeof
thepolarizedorgrounding-typeplug.
Apolarizedplughastwobladeswith
onewiderthantheother.Agrounding
typeplughastwobladesandathird
groundingprong.Thewidebladeorthe
thirdprongareprovidedforyoursafety.
Iftheprovidedplugdoesnotfitinto
youroutlet,consultanelectricianfor
replacementoftheobsoleteoutlet.
10. Protectthepowercordfrombeing
walkedonorpinchedparticularlyat
plugs,conveniencereceptacles,andthe
pointwheretheyexitfromtheapparatus.
11. Onlyuseattachments/accessories
specifiedbythemanufacturer.
12. Useonlywiththecart,stand,tripod,
bracket,ortablespecifiedbythe
manufacturer,orsoldwiththeapparatus.
Whenacartisused,usecautionwhen
movingthecart/apparatuscombination
toavoidinjuryfromtip-over.
13. Unplugthisapparatusduringlightning
stormsorwhenunusedforlongperiods
oftime.
14. Referallservicingtoqualifiedservice
personnel.Servicingisrequiredwhen
theapparatushasbeendamagedinany
way,suchaspower-supplycordorplug
isdamaged,liquidhasbeenspilledor
objectshavefallenintotheapparatus,the
apparatushasbeenexposedtorainor
moisture,doesnotoperatenormally,or
hasbeendropped.
Handling of the unit
Becarefulnottospillwaterorotherliquidson
theunit.Becautiousnottogetcombustibleor
metallicmaterialinsidethebody.Ifusedwith
foreignmatterinside,thecameraisliableto
failortogetcauseoffireorelectricshock.
• Removedustordirtonthesurfaceofthe
lenswithablower.
• Useadrysoftclothtocleanthebody.Ifit
isverydirty,useaclothdampenedwitha
smallquantityofneutraldetergentthen
wipedry.
• Avoidtheuseofvolatilesolventssuch
asthinners,alcohol,benzeneand
insecticides.
Theymaydamagethesurfacefinishand/
orimpairtheoperationofthecamera.
Operating and storage
location
Avoidviewingaverybrightobject(suchas
lightfittings)duringanextendedperiod.Avoid
operatingorstoringtheunitinthefollowing
locations.
• Extremelyhotorcoldplaces(operating
temperature-10°Cto50°C,however,we
recommendthattheunitbeusedwithin
atemperaturerangeof0°Cto45°C)
• Dampordustplace
• Placesexposedtorain
• Placessubjecttostrongvibration
• Closetogeneratorsofpowerful
electromagneticradiationsuchasradio
orTVtransmitters.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TOREDUCETHERISKOFELECTRICSHOCK
DONOTREMOVECOVER(ORBACK)
NOUSER-SERVICEABLEPARTSINSIDE
REFERSERVICINGTOQUALIFIEDSERVICEPERSONNEL.
Thislightningflashwitharrowheadsymbolwithinanequilateraltriangleis
intendedtoalerttheusertothepresenceofuninsulateddangerousvoltage
withintheproduct’senclosurethatmaybeofsufficientmagnitudeto
constituteariskofelectricshocktopersons.
Theexclamationpointwithinanequilateraltriangleisintendedtoalertthe
usertothepresenceofimportantoperatingandmaintenance(servicing)
instructionsintheliteratureaccompanyingtheproduct.
FCC WARNING: Thisequipmentmaygenerateoruseradiofrequencyenergy.Changesor
modificationstothisequipmentmaycauseharmfulinterferenceunlessthemodificationsare
expresslyapprovedintheinstructionmanual.Theusercouldlosetheauthoritytooperatethis
equipmentifanunauthorizedchangeormodificationismade.
REGULATORY INFORMATION: FCC Part 15
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,
pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
againstharmfulinterferencewhentheequipmentisoperatedinacommercialenvironment.
Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalled
andusedinaccordancewiththeinstructionmanual,maycauseharmfulinterferencetoradio
communications.
Operationofthisequipmentinaresidentialareaislikelytocauseharmfulinterferenceinwhich
casetheuserwillberequiredtocorrecttheinterferenceathisownexpense.
• Asuitableconduitentries,knock-outsorglandsshallbeprovidedinthecableentriesofthis
productintheenduser.
• Caution:Dangerofexplosionifbatteryisincorrectlyreplaced.Replacedonlywiththesameor
equivalenttyperecommendedbythemanufacturer.Disposeofusedbatteriesaccordingto
themanufacturer’sinstructions.
• Holesinmetal,throughwhichinsulatedwirespass,shallhavesmoothwellroundedsurfaces
orshallbeprovidedwithbrushings.
ThisClassAdigitalapparatuscomplieswithCanadianICES-003.
CetappareilnumériquedelaclasseAestconformeàlanormeNMB-003duCanada.
AB28
MODEL
LW9422 series
Please read this manual carefully before operating
your set and retain it for future reference.
OWNER'S MANUAL
Network Dome Camera
a
b
c
d
e
f
g
h
i
aBNC connector cover cap
bVideo output BNC connector
cData Port A (RJ-45)
Inputdataportforalarm(relay)signal.RS-485datacommunicationisnotavailable.
dData Port B (RJ-45)
Outputdataportforalarm(relay)signal.
eAUDIO IN (Line Level Input)
Inputforamonomicrophone,oraline-inmonosignal.
fAUDIO OUT (Line Level Output)
Connecttoanactivespeakerwithabuilt-inamplifier.
gPower input jack
hETHERNET Port
ConnectstoaPCoranetworkviaahubwitha10BASE-T/100BASE-TXcableattached
RJ-45connector.
iDome Cover
Accessories
• SoftwareInstallationCD
• Coveradaptor
• Mountadaptor
• RJ-45Cable
• RJ-45adaptorcable
• Wrench
• M3SAMSScrews
Item LW9422 Series
ImageSensor 6.49mm(1/2.8Type)CMOSSensor
TotalPixels 1920(H)X1080(V),2M
Lens F1.6(Wide)toF2.1(Tele),f=5.3to63.6mm
x12OpticalZoom,x12DigitalZoom
Day&Night ICRDay&Night(Day/Night/Auto)
Mininum
Illumination
(30IRE)
Color 1lx(AGCHigh, Sens-upOff )
B/W 0.1lx(AGCHigh, Sens-upOff )
WhiteBalance Auto/ATW/OnePush/Manual
ShutterSpeed 1/160to1/10000
Iris Auto/Manual
BLC Off/WDR/BLC
3D-DNR OFF/LOW/MIDDLE/HIGH
AGC OFF/LOW/MIDDLE/HIGH
PrivacyMask 8Masks
Multi-Streaming DualStreaming
VideoOut 1xBNC
Resolution(Maximum) Upto1920x1080
FrameRate(Maximum) 30fps@1080p(1920x1080)
BitRate 256kbpsto10240kbps
AudioCompression G.711,G726
AudioIn/Out 1/1
SampleRate 8KHz
AudioBitRate G.711:64kbps,G.726:24kbps,32kbps
Ethernet 10/100Ethernet
Protocol TCP/IP,UDP,Multicast,DHCP,SMTP,HTTP,SNMP,RTP,RTSP
RemoteS/W LGIpsoluteVMSorWebClient
Pan/Tilt TravelRange Pan:360˚(Endless),Tilt:180˚
Speed Preset 500˚/second
Jog 0.1˚to360˚/second
Preset 128
Pattern 4Patterns(760command/Pattern)
AutoPan 2pointsto8points
Group 9Groups(8presets/Group)
Sensor/
Alarm
Sensor 4Inputs,Photo-CouplerInput
Alarm 2RelayOutputs,MaxLoad:DC30V1A/AC125V0.3A
IPResetButton Support
Misc. MountAccessory MountAdaptor
Material Dome Polycarbonate
Internal Polycarbonate,ABS
External Aluminum
RatedPower PoE+/AC24V(49W)
Waterproof IP66
Fan AlwaysON
Heater OperationstartfromInternalTemperature10˚C
Operation
Temperature
-20˚Cto50˚C
Weight about3.3Kg
Dimension Ø195.8mmx229mm
Specifications Part Names and Functions

Connecting Display device
Thevideosignalconnectionbetweenthe
cameraandthemonitor.
ALARM input connection
Connectsensorandalarmdevicesto
correspondingterminalsaccordingly.
E
D
C
B
A
G
F
H
Alarmdevice
Alarmdevice
Alarmdevice
Alarmdevice
RJ-45Adaptercable PortA
PORT A of the LW9422 series
Description Color
ALARMINCOM Black
ALARMIN1 Brown
ALARMIN2 Red
ALARMIN3 Orange
ALARMIN4 Green
ALARM output connections
E
D
C
B
A
G
F
H
Alarmdevice
RJ-45Adaptercable PortB
GND
IPReset
Alarmdevice
PORT B of the LW9422 series
Description Color
ALARMOUT1A Blue
ALARMOUT1B Violet
ALARMOUT2A Gray
ALARMOUT2B White
IPRESET Pink
GND Red/White
CAUTION:
Outputspecificationsarelowactive,open-
collectorandadrivecapacityofDC30V1A
/AC125V0.3A.Connectingthealarmout
incorrectlymaycausedamagingthecamera.
Connecting Network
ConnecttheIPcameratoyournetwork
usingastandardRJ-45networkcableas
shownbelow.
Router
Connecting power source
ConnectaAC24VorPoE+powersourceto
thepowerinputterminalasshownbelow.
(ConnecttotheAC24VULListed,Class2
PowerSupplyonlyontheunit.)
NOTE:
IncaseofconnectingbothAC24Vand
PoE+,PoE+hasapriority.
AC 24 V
or
PoE+
Connecting Microphone and
Speaker Device
Optionallyconnectanactivespeakerand/or
externalmicrophonewithabuilt-inamplifier.
NOTE:
Keepthemicrophoneawayfromthespeaker
toavoidhowling.
YoucanrecordyoursurveillanceenvironmentwiththeSDcardevenifthenetworkisdisconnected
condition.
To insert the SD card
1. Removethedomecover.
2. InserttheSDcardcarefullyasshowninthefollowingillustrations.MakesuretheSD card
terminalpositionbeforeinserttheSDcard.PushthebackendoftheSDcardtofixitatthelast
step.
NOTES:
• DonotusethepowertoomuchwhenyouinserttheSDcard.TheSDcardmaybe
damaged.
• IfyouinserttheSDcardinthewrongposition,theSDcardmaybedamagedoritmay
causethemalfunctionoftheSDCardSlot.
• KeeptheterminalpartoftheSDcardinclean.BecarefultheterminalpartoftheSDcard
nottodusty.
• AstheSDcardisconsumable,theSDcardenditsdaysandmaybenotabletosavedataif
youuseitmorethanovercertaintimes.Inthiscase,replaceSDcardtobuy anewone.
Remove the SD card
1. PressthebackendoftheSDcardtoreleasethelockcondition.
2. TaketheSDcardoutcarefullyfromthecamera.ItmaycauseamalfunctionoftheSD card
ortheSDcardslotifyouusethepowertoomuchatlockstatus.
CAUTION:
• IfyouinstalltheSDcardonthecameraandremovewiththeSDcardconditionindicator
lightson,youmustunmounttheSDcardbyusingthe[SDCard>Configuration>Disk
Management>Unmount]menu.TheSDcarddataiscompromisedorthecameramay
notoperatenormally,ifyouremovethecardwithoutuse[Unmount]function.
• DonotinsertMicroSDcardtoSDcardadapter.ItisrecommendedtouseastandardSD
card.
• InserttheSDcardbeforeinstallthecamera.
• LGElectronicsisnotresponsiblefordeleteddatacausedbyusermishandlingwhenyou
insertorremovetheSDcard.
Wall mount (optional)
Installthecamerabythefollowingorder.
1. Installthewallmountassemblyas
shownbelow.
2. Drillaholeonthewallwhereyouwant
toinstallthepipe.Passtheconnection
cablethroughthewallmountassembly
sothattheyhangdown.
3. Connectthesafetycabletothecamera
inordertopreventacamerafromfalling.
4. Connectthecabletothecamerajack.
5. Assemblethecameratothemounting
adaptorbyturningitclockwise.Tighten
theM3SAMSScrewsandthenalignthe
coveradaptorandmainbody.
CAUTION:
Removethedomecovercarefullytoprevent
falling.
Pendant mount (optional)
Installthecamerabythefollowingorder.
1. Installthependantmountassembly.
2. Drillaholeonthewallwhereyouwant
toinstallthepipe.Passtheconnection
cablethroughthependantmount
assemblysothattheyhangdown.
3. Connectthesafetycabletothecamera.
4. Connectthecablestothecamerajack.
5. Assemblethecameratothemounting
adaptorbyturningitclockwise.Tighten
theM3SAMSScrewsandthenalignthe
coveradaptorandmainbody.
Parapet mount (optional)
1. Installtheparapetmountassemblyas
shownbelow.
2. Drillaholeonthewallwhereyou
wanttoinstalltheparapet.Passthe
connectioncablethroughtheparapet
mountassemblysothattheyhang
down.
3. Connectthesafetycabletothecamera.
4. Connectthecablestothecamerajack.
5. Assemblethecameratothemounting
adaptorbyturningitclockwise.Tighten
theM3SAMSScrewsandthenalignthe
coveradaptorandmainbody.
Connection Using the SD Card
Installation