Liberty Garden Navigator 712 User manual

2
TOOLS REQUIRED:
PARTS LIST
HARDWARE INCLUDED
BB
A
B ED
CC
BB. Allen bolts (2)
A. Crank handle (1) B. Leader hose (1) C. Swing arm (1) D. Basket (1) E. Hose reel (1)
DD
DD. Allen screw (1)CC. Lock nuts (2)
Note: Hardware not shown to actual size.
Estimated Assembly Time : 10 minutes (not including mounting the hose reel)
PRE-ASSEMBLY
The wall mounting hardware is NOT included with this unit. Check with the retailer or visit a hardware store to purchase.
IMPORTANT: LAY OUT ALL PARTS AND FASTENERS. MAKE SURE ALL PARTS ARE
ACCOUNTED FOR. IF ANY PART IS MISSING PLEASE CONTACT LIBERTY GARDEN PRODUCTS
AT 1-866-820-5805. DO NOT CONTACT THE RETAILER. YOU CAN ALSO VISIT OUR
WEBSITE, WWW.LIBERTYGARDENPRODUCTS.COM, FOR MORE INSTRUCTIONS, PICTURES
AND HELPFUL HINTS.
AA
AA. Allen wrench (Supplied)
Adjustable
Wrench
Stud
Finder
Hammer
Drill
Electric
Drill
Phillips
screwdriver
or bit for an
electric drill
7/16 in. and
3/8 in. Socket
and Socket
wrench
C

3
The following hardware (not included)
is recommended for installation:
1. BRICK OR MASONRY ANCHOR SLEEVES
(2) 7 or 8 mm x 60 mm masonry wall anchors (5/16” x 2 1/2”)
(2) Anchor sleeves
(2) Washers
(2) Lock washers
(2) Nuts
The following hardware (not included) is recommended for installation:
3. WOOD SCREWS
(2) 7 or 8 mm x 60 mm wood screws (5/16” x 2 1/2”)
(2) Washers
The following hardware (not included)
is recommended for installation:
2. BRICK OR MASONRY SCREWS
(2) 7 or 8 mm x 60 mm masonry screws (5/16” x 2 1/2”)
(2) Washers
at a convenient height. Mark the position of each suspension
hole on the wall. Remove the hose reel.
insert the anchor and sleeve into the drilled holes until the steel
sleeve is completely in the wall.
r, lock washer, and nut over each
wall anchor and tighten securely.
ient height.
Mark the position of each suspension hole on the wall. Remove the hose reel.
Align the hose reel suspension holes with the pilot holes.
Attach the hose reel to the wall using the wood screws with washers and tighten securely.
To learn more, watch a video on our warranty and care section @ www.libertygardenproducts.com
NOTE:Drill hole diameters
may vary based on anchor
sleeve, concrete screw, and
wood screw manufacturer.
Check product recommendations
before drilling holes.
wall at a convenient height. Mark the position of each
suspension hole on the wall. Remove the hose reel.
Align the hose reel suspension holes with the pilot holes.
Attach the hose reel to the wall using the concrete screws
with washers and tighten securely.
marked positions on the wall.
d positions on the wall.
marked positions on the wall.
INSTALLATION This hose reel must be mounted to a solid masonry wall or to wall studs
Mounting Hole
Size: 1/4”
Mounting Hole
Size: 1/4”
Mounting Hole
Size: 5/16”
TIP: Remember to use the correct size and quantity of hardware to properly support the
total weight of the unit. A standard 100' length of garden hose weighs approximately 15 lbs.
Filled with water, the additional weight can exceed 20 lbs. The mounting hardware must be
able to support the combined weight of the unit, garden hose, plus water.
: 5/16”

4
ASSEMBLY
1
3
Attach the hose reel (E) to the swing arm
(C) by hanging the reel on the small slot
located at the front of the arm.
Line up the holes in the hose reel (E) with
the swing arm (C) and insert long Allen
bolts (BB)
2
Tighten Allen bolts (BB) with the
supplied Allen wrench (AA) at the
same time using fingers screw on
lock nuts (CC) to secure swing
arm (C) to hose reel (E)
Pliers (not included) may be
needed to hold and tighten lock
nuts.
CAUTION: DO NOT OVER
TIGHTEN LOCK NUTS AND
ALLEN BOLTS.
BB
AA
FIGURE 1
FIGURE 3
FIGURE 2
C
E
C
C
EBB
E

5
ASSEMBLY
4
FIGURE 7
Align the holes in the crank handle (A) with the
crank handle shaft on the hose reel (E). Insert the
short Allen screw (DD) into the crank handle and
tighten with supplied Allen wrench (AA)
6
5
Attach leader hose (B) to swivel connector on
the hose reel (D). Attach end of leader hose
to water source.
7Attach the basket (D) to the swing arm
(C) by fastening the keyhole opening
to the resting pins then dropping the
basket into the set position.
Attach your garden hose to the hose connector on
the hose reel (E). The hose is now ready to wind
around the spool. The Single Arm Navigator holds
up to 125 ft. of 5/8” garden hose.
FIGURE 5 FIGURE 6
B
E
E
FIGURE 4
A
DD
E
AA
A
D