Liberty DigitaLinx DL-SCU21C User manual

Rev 190119 Phone: 719-260-0061
Toll-Free: 800-530-8998
Fax: 719-260-0075
DL-SCU21C Owners Manual
11675 Ridgeline Drive
Colorado Springs, CO
80921

DL-SCU21C Owners Manual
2
Important Safety Instrucons
»Please completely read and verify you understand all instrucons in this manual before operang this equipment.
»Keep these instrucons in a safe, accessible place for future reference.
»Heed all warnings.
»Follow all instrucons.
»Do not use this apparatus near water.
»Clean only with a dry cloth.
»Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
»Use only accessories specied or recommended by Intelix.
»Explanaon of graphical symbols:
◊ Lightning bolt/ash symbol: the lightning bolt/ash and arrowhead within an equilateral triangle
symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the
product enclosure which may be of sucient magnitude to constute a risk of shock to a person or
persons.
◊ Exclamaon point symbol: the exclamaon point within an equilateral triangle symbol is intended
to alert the user to the presence of important operang and maintenance (servicing) instrucons
in the literature accompanying the product.
»WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
»Use the mains plug to disconnect the apparatus from the mains.
»THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE.
»Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of
your obsolete outlet. Cauon! To reduce the risk of electrical shock, grounding of the center pin of this plug must be
maintained.
»Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and the
point where they exit from the apparatus.
»Do not block the air venlaon openings. Only mount the equipment per Intelix’s instrucons.
»Use only with the cart, stand, table, or rack specied by Intelix or sold with the equipment. When/if a
cart is used, use cauon when moving the cart/equipment combinaon to avoid injury from p-over.
»Unplug this apparatus during lightning storms or when unused for long periods of me.
»Cauon! Shock Hazard. Do not open the unit.
»Refer to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

DL-SCU21C Owners Manual
3
Table of Contents
Product Overview��������������������������������������������������������������������������������������������������������������������������������������� 4
Product Overview��������������������������������������������������������������������������������������������������������������������������������������� 4
Front and Rear Panels��������������������������������������������������������������������������������������������������������������������������������� 5
Front Panel���������������������������������������������������������������������������������������������������������������������������������������������������� 5
Rear Panel����������������������������������������������������������������������������������������������������������������������������������������������������� 6
Installaon Instrucons������������������������������������������������������������������������������������������������������������������������������ 7
Mount the Switcher��������������������������������������������������������������������������������������������������������������������������������������� 7
Mounng Instrucons ............................................................................................................................ 7
Connect Sources�������������������������������������������������������������������������������������������������������������������������������������������� 7
Connect Displays������������������������������������������������������������������������������������������������������������������������������������������� 7
Connect USB Peripherals������������������������������������������������������������������������������������������������������������������������������� 8
Connect Audio (Oponal)������������������������������������������������������������������������������������������������������������������������������ 8
Connect RS232 Control (Oponal) ���������������������������������������������������������������������������������������������������������������� 8
Applying Power ��������������������������������������������������������������������������������������������������������������������������������������������� 9
Switching Capabilies ����������������������������������������������������������������������������������������������������������������������������������� 9
A/V Diagram �������������������������������������������������������������������������������������������������������������������������������������������� 10
EDID Management ����������������������������������������������������������������������������������������������������������������������������������� 11
RS232 Control Commands������������������������������������������������������������������������������������������������������������������������� 12
Source Switching Commands ����������������������������������������������������������������������������������������������������������������������12
CEC Display Control Commands������������������������������������������������������������������������������������������������������������������13
Switcher RS232 Sengs Commands �����������������������������������������������������������������������������������������������������������14
RS232 Programming Commands ����������������������������������������������������������������������������������������������������������������15
System Commands��������������������������������������������������������������������������������������������������������������������������������������19
Technical Specicaons ���������������������������������������������������������������������������������������������������������������������������� 20

DL-SCU21C Owners Manual
4
The DL-SCU21C is a 2x1 HDMI 2.0b auto switcher featuring one HDMI input, one USB-C input and
one HDMI output. The USB-C input supports video, data (USB host) and power charging up to 40w.
There is a built in 2 port USB 3.0 hub that is backwards compable with USB 2.0 and USB 1.1 formats.
This switcher supports video resoluons up to 4Kx2K@60Hz 4:4:4, HDR, and mulchannel audio. The
USB-C input supports Display Port over Alternate Mode (ALT-DP), any laptop computer used with this
device must support this mode.
NOTE: When using a laptop with USB-C ports, check the laptops capability for supporng ALT-DP for
video, data and power charging, not all laptops may support all three funcons at once with external
devices.
In addion to passing nave EDID informaon from the display to an input on the switcher, there
are mulple built-in EDID sengs to choose from to simplify an installaon. The switcher will de-
embed 2 channel analog audio for audio reinforcement which is de-embedded from the HDMI output.
The devices switching funcons can be controlled via RS232 and front panel control buons can be
congured to control 3rd party devices connected to the switcher such as a TV display via CEC or RS232.
When in auto-switch mode, the switcher will switch to an input as soon as a new source is connected.
When the acve source is removed, the switcher will select the prior source connected. When switching
between HDMI and USB-C video inputs, the USB B Host port will follow HDMI and USB-C will act as a
USB host disengaging USB B Host control.
Product Overview
Product Contents
• DL-SCU21C 2x1 Auto Presentaon Switcher
• Quick Install Guide
• (1) 5 pin Phoenix Connector
• (1) DB9 - 3 pin Phoenix RS232 breakout cable
• (1) DC24V 2.71A power supply with US power plug
• (2) Mounng Clips with 4 screws
• (4) Plasc Cushions

DL-SCU21C Owners Manual
5
Front and Rear Panels
Front Panel
24
13 5
1. POWER LED - Illuminates solid RED when power is properly applied
2. INPUT LEDs:
• HDMI - Illuminates solid GREEN when input is selected in auto switch mode, illuminates
orange when input is selected in manual switch mode
• USB-C - Illuminates solid GREEN when input is selected in auto switch mode, illuminates
orange when input is selected in manual switch mode
• SELECT AUTO / 3s - Switches between auto and manual switch mode. Hold down for 3
seconds to enable /disable audio switch mode.
3. DISPLAY:
• ON - Press to turn display ON either by CEC or RS232
• OFF - Press to turn display OFF either by CEC or RS232
• Volume Mute - Press to mute display either by CEC or RS232
• Volume Down - Press to turn display volume down either by CEC or RS232
• Volume Up - Press to turn display volume up either by CEC or RS232
4. EDID - Dip switch seng for EDID management
5. FW - USB port for rmware upgrade procedure

DL-SCU21C Owners Manual
6
Rear Panel
27
134568
1. HDMI IN - HDMI input port for connecng HDMI source
2. USB-C IN - USB-C input port for connecng source; USB-C port supports video, data (USB
Host) and power charging.
3. HDMI OUT - HDMI output for connecng to TV display
4. AUDIO OUT - 5 pin phoenix; balanced le and right analog audio output
5. RS232 - 3 pin phoenix; output port for connecon display or 3rd party control
6. HOST - USB B port for USB host device i.e. computer
7. DEVICES 1/2 - (2) USB A ports for USB client devices i.e. web camera, web microphone
8. DC 24V - Locking power supply port

DL-SCU21C Owners Manual
7
Installaon Instrucons
Mount the Switcher
Mounng Instrucons
At least 2 inches of free air space is required on both sides of the DL-SCU21C for proper side venlaon. Avoid
mounng the DL-SCU21C near a power amplier or any other source of signicant heat.
Remove the four screws on both sides of the DL-SCU21C, then aach the supplied mounng clips to the DL-
SCU21C for surface or rack mounng.
Connect Sources
Connect Displays
Connect a source device to the HDMI input using a High Speed HDMI cable that is less than or equal to 1.5
meters in length for 4k60 signals and 5 meters for 1080p signals. For source devices that are further away, it is
highly recommended to install an HDMI extender such as the Digitalinx DL-HD70, DL-HDE100, DL-HDE100-H2
or the DL-HD2100.
Connect a source device to the USB-C input using a USB-C cable capable of support video, data and power
charging no longer than 2 meters (6.6’) in total length. The DL-SCU21C supports ALT-DP mode for video, to
ensure a laptop is compable with the DL-SCU21C check the laptops capability of supporng this mode.
Note that not all laptops will support video, data and power charging all at once with external devices�
Connect the display device to the HDMI output using a High Speed HDMI cable that is less than or equal to 1.5
meters in length for 4k60 signals and 5 meters for 1080p signals. For display device that is further away, it is
highly recommended to install an HDMI extender such as the Digitalinx DL-HD70, DL-HDE100, DL-HDE100-H2
or the DL-HD2100.

DL-SCU21C Owners Manual
8
Connect USB peripherals, such as a USB 3.0 , 2.0 or 1.1 compable Mic or Camera, to the USB-A client ports on
the DL-SCU21C with USB cables equal to or less than 4.5 meters or 15’ in total length.
Connect a USB host, such as a computer, to the USB-B host port on the DL-SCU21C with a USB A to B cable equal
to or up to 4.5 meters or 15 feet in total length.
For USB devices that are further away from these distances, it is highly recommended to install a USB extender
such as the Digitalinx DL-USB2 or the Intelix INT-3.1CX.
The USB-C port also behaves as a USB host for the USB hub in addion to transporng video and power charging.
Connect a USB host, such as a computer, to the USB-C port on the DL-SCU21C with a USB type C cable equal
to or up to 2 meters or 6.6 feet in total length. Check the cable and laptops capability for supporng video and
data simultaneously.
Connect USB Peripherals
Connect an audio amplier to the audio output of the DL-SCU21C, the switcher features a le and right balanced
audio output.
Connect Audio (Oponal)
There are two ways to connect and use RS232 control with the DL-SCU21C, connect the RS232 DB-9 to 3
pin phoenix cable to a control system to control of the DL-SCU21C funcons or connect the RS232 DB-9 to 3
pin phoenix cable to a display device to control the display using the front panel control buons on the DL-
SCU21C. To program or pre-load RS232 control commands for a display using front panel buons see secon
RS232 Control Commands, pg 11.
Connect RS232 Control (Oponal)
RS232 Wiring
Connect the controller or display RX signal
to TX on the DL-SCU21C, then connect the
controller or device TX signal to RX on the
DL-SCU21C.
RS232 Sengs:
• 9600 baud
• 8 Data Bits
• 1 Stop Bit
• Parity = none
DL-SCU21C RS232 Port
Conncected RS232 Device pins
TX G RX
RX G TX

DL-SCU21C Owners Manual
9
Connect the included power supply to the DL-SCU21C and lock the power supply to the power connector by
twisng the locking collar clockwise.
Applying Power
Switching Capabilies
Switch between sources and displays using the switches front panel buons or by serial ./ RS232 control.

DL-SCU21C Owners Manual
10
A/V Diagram
Display
Laptop (HDMI)
Audio
System
Control System
Laptop (USB-C)
USB Camera
USB Mic
HDMI
USB
AUDIO
RS232

DL-SCU21C Owners Manual
11
EDID Management
EDID (Extended Display Idencaon Data) is data generated from a connected display in an HDMI system to
communicate the resoluon capabilies to a connected video source. The DL-SCU21C features an EDID copy
mode that can be used to copy EDID sengs from the display connected to the HDMI output of the switcher
so they can be communicated to the sources connected to the video inputs If preset EDID tables are preferred
rather than using EDID copy use the dipswitch sengs below for the desired resoluon and audio sengs.
When in the down posion, the switch represents “0” of OFF, when the switch posion in the up posion it
represents “1” or ON.
Note: When using EDID copy, if EDID fails the EDID will default to 1080p.
EDID Seng Posion 1 Posion 2 Posion 3 Posion 4
EDID Copy (default) 0 0 0 0
1280X720 @60HZ, Stereo Audio 0 0 0 1
1920x1080 @ 60Hz, DVI (No Audio) 0 0 1 0
1920x1080 @ 60Hz, Stereo Audio 0 1 0 0
1920x1080 @ 60Hz, Mul-channel Audio 0 1 0 1
3840x2160 @ 30Hz 4:2:0, HDR,
Stereo Audio
0 1 1 1
3840x2160 @ 30Hz 4:2:0, HDR,
Mul-channel Audio
1 0 0 0
3840x2160 @ 60Hz 4:4:4,
Stereo Audio 1 0 0 1
3840x2160 @ 60Hz 4:4:4,
Mul-channel Audio 1 0 1 0

DL-SCU21C Owners Manual
12
RS232 Control Commands
RS232 Sengs: 9600 baud, 8 Data bits, 1 Stop bit, Parity = None
All responses end in a carriage return (hex 0D) and a line feed (hex 0A) unless otherwise noted.
<CR> = Carriage return (Hex 0D)
<LF> = Line Feed (Hex 0A)
Descripon Command Examples
Switches to HDMI input #SET_AV H Command:
#SET_AV H<CR><LF>
Response:
@AV H<CR><LF>
Switches to USB-C input #SET_AV C Command:
#SET_AV C<CR><LF>
Response:
@AV C<CR><LF>
Query current input source #GET_AV Command:
#GET_AV<CR><LF>
Response:
@AV H<CR><LF>
or
@AV C<CR><LF>
Enable auto switching mode #SET_AUTO_SWITCH 1 Command:
#SET_AUTO_SWITCH 1<CR><LF>
Response:
@AUTO_SWITCH 1<CR><LF>
Disable auto switching mode #SET_AUTO_SWITCH 0 Command:
#SET_AUTO_SWITCH 0<CR><LF>
Response:
@AUTO_SWITCH 0<CR><LF>
Query current auto switching mode
status
#GET_AUTO_SWITCH Command:
#GET_AUTO_SWITCH<CR><LF>
Response:
@AUTO_SWITCH 1<CR><LF>
or
@AUTO_SWITCH 0<CR><LF>
Source Switching Commands

DL-SCU21C Owners Manual
13
Descripon Command Examples
Turns connected display ON #SET_DISPLAY 1 Command:
#SET_DISPLAY 1<CR><LF>
Response:
@DISPLAY 1<CR><LF>
Turns connected display OFF #SET_DISPLAY 0 Command:
#SET_DISPLAY 0<CR><LF>
Response:
@DISPLAY 0<CR><LF>
Increases volume by 1 value #SET_VOL + Command:
#SET_VOL +CR><LF>
Response:
@VOL +<CR><LF>
Decreases volume by 1 value #SET_VOL - Command:
#SET_VOL -CR><LF>
Response:
@VOL -<CR><LF>
Mutes / unmutes audio #SET_AUDIO_MUTE Command:
#SET_AUDIO_MUTE<CR><LF>
Response:
@AUDIO_MUTE_UNMUTE<CR><LF>
CEC Display Control Commands
The following commands can be used to control the display connected to the HDMI output of the DL-SCU21C
via CEC.
To use this feature a CEC compable TV display must be used and the feature must be turned ON in the display
menu properes.
NOTE: Not all CEC display control funcons below may be supported by a TV display manufacturer. Test CEC
display control rst before deploying to be sure what your TV will support.

DL-SCU21C Owners Manual
14
Descripon Command Examples
Set baud rate seng #SET_RS232_BAUD [B]
[B] = 0 (115200)
1 (57600)
2 (38400)
3 (19200)
4 (9600)
5 (4800)
6 (2400)
Command:
#SET_RS232_BAUD 0<CR><LF>
Response:
@RS232_BAUD 0<CR><LF>
Query current baud rate seng #GET_RS232_BAUD Command:
#GET_RS232_BAUD<CR><LF>
Response:
@RS232_BAUD 0<CR><LF>
Switcher RS232 Sengs Commands
Use the following command structure to set the DL-SCU21C baud rate seng for RS232 control. By default the
RS232 baud rate seng is set to 9600 bps.

DL-SCU21C Owners Manual
15
Descripon Command Examples
Sends ASCII formaed string to
display via RS232 when the ON
buon is pressed
#SET_ON_{B}_{T}:XXXX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XXXX = ASCII Formatted
Command String
Command:
#SET_ON_04_01:POWER ON<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@DISPLAY ON TO SEND: POWER ON
The above example sends the
command POWER ON to the display
at baud rate setting 9600bps
with the delay time set at 1
second.
Sends ASCII formaed string to
display via RS232 when the OFF
buon is pressed
#SET_OF_{B}_{T}:XXXX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XXXX = ASCII Formatted
Command String
Command:
#SET_OF_04_01:POWER OFF<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@DISPLAY OFF TO SEND: POWER OFF
The above example sends the
command POWER OFF to the display
at baud rate setting 9600bps
with the delay time set at 1
second.
RS232 Programming Commands
Use the following commands to program and pre-load RS232 strings when the front panel buons are used for
display control.
To control a display using the DL-SCU21C RS232 port, be sure to locate the appropriate display operaon
commands in the TV displays owners manual.

DL-SCU21C Owners Manual
16
Descripon Command Examples
Sends ASCII formaed string
to display via RS232 when the
VOLUME UP buon is pressed
#SET_AU_{B}_{T}:XXXX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XXXX = ASCII Formatted
Command String
Command:
#SET_AU_04_01:VOL+<CR><LF>
Response:
@BAUDRATE 9600<CR>
@DELAY TIME 1S
@VOLUME + TO SEND: VOL +
The above example sends the
command VOL+ to the display at
baud rate setting 9600bps with
the delay time set at 1 second.
Sends ASCII formaed string
to display via RS232 when
the VOLUME DOWN buon is
pressed
#SET_AD_{B}_{T}:XXXX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XXXX = ASCII Formatted
Command String
Command:
#SET_AD_04_01:VOL-<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@VOLUME - TO SEND: VOL -
The above example sends the
command VOL - to the display at
baud rate setting 9600bps with
the delay time set at 1 second.
Sends ASCII formaed string
to display via RS232 when the
MUTE buon is pressed
#SET_AM_{B}_{T}:XXXX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XXXX = ASCII Formatted
Command String
Command:
#SET_AM_04_01:MUTE<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@VOLUME MUTE TO SEND: MUTE
The above example sends the
command MUTE to the display at
baud rate setting 9600bps with
the delay time set at 1 second.
RS232 Programming Commands - connued

DL-SCU21C Owners Manual
17
Descripon Command Examples
Sends HEX formaed string
to display via RS232 when
the ON buon is pressed
#SET_H_ON_{B}_{T}:XX XX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XX XX = HEX Formatted
Command String
Command:
#SET_H_ON_04_01:A1 B2 C3<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@DISPLAY ON TO SEND: A1 B2 C3
The above example sends the
command A1 B2 C3 to the display
at baud rate setting 9600bps with
the delay time set at 1 second.
Sends HEX formaed string
to display via RS232 when
the OFF buon is pressed
#SET_H_OF_{B}_{T}:XX XX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XX XX = HEX Formatted
Command String
Command:
#SET_H_OF_04_01:11 22 33<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@DISPLAY OFF TO SEND: 11 22 33
The above example sends the
command 11 22 33 to the display
at baud rate setting 9600bps with
the delay time set at 1 second.
RS232 Programming Commands - connued

DL-SCU21C Owners Manual
18
Descripon Command Examples
Sends HEX formaed string
to display via RS232 when
the VOLUME UP buon is
pressed
#SET_H_AU_{B}_{T}:XX XX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XXXX = HEX Formatted
Command String
Command:
#SET_H_AU_04_01:D1 E2 F3<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@VOLUME + TO SEND: D1 E2 F3
The above example sends the
command D1 E2 F3 to the display at
baud rate settings, 9600
bps with the delay time set at 1
second.
Sends HEX formaed string
to display via RS232 when
the VOLUME DOWN buon is
pressed
#SET_H_AD_{B}_{T}:XX XX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XX XX = HEX Formatted
Command String
Command:
#SET_H_AD_04_01:22 33 44<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@VOLUME - TO SEND: 22 33 44
The above example sends the
command 22 33 44 to the display at
baud rate settings, 9600 bps with
the delay time set at 1 second.
Sends HEX formaed string
to display via RS232 when the
MUTE buon is pressed
#SET_H_AM_{B}_{T}:XX XX
{B} = Baud Rate
00 (115200)
01 (57600)
02 (38400)
03 (19200)
04 (9600)
05 (4800)
06 (2400)
{T} = Delay in seconds
(00-99)
XX XX = HEX Formatted
Command String
Command:
#SET_H_AM_04_01:33 4455<CR><LF>
Response:
@BAUDRATE 9600
@DELAY TIME 1S
@VOLUME MUTE TO SEND: 33 44 55
The above example sends the
command 33 44 55 to the display at
baud rate settings, 9600 bps with
the delay time set at 1 second.
RS232 Programming Commands - connued

DL-SCU21C Owners Manual
19
Descripon Command Examples
Query current rmware
version
#GET_FIRMWARE_VERSION Command:
#GET_FIRMWARE_VERSION<CR><LF>
Response:
@v1.0.0<CR><LF>
System Reboot #REBOOT Command:
#REBOOT<CR><LF>
Response:
@REBOOT<CR><LF>
Reset system to factory
defaults
#FACTORY_RESET Command:
#FACTORY_RESET<CR><LF>
Response:
@FACTORY_RESET<CR><LF>
System Commands

DL-SCU21C Owners Manual
20
Technical Specicaons
Video
Video Inputs One (1) HDMI, (1) USB-C
Video Input Connector (1) HDMI type A, (1) USB-C
Input Video Signal HDMI for HDMI input, ALT-DP Mode for USB-C
Video Output (1) HDMI
Video Output Connector (1) HDMI type A
Input Resoluon Support Up to 3840 x 2160 @60Hz / 4:4:4 / 8 bit deep color for HDMI
Up to 3840 x 2160 @30Hz / 4:4:4 / 8 bit deep color for USB-C
Output Resoluon Support Up to 3840 x 2160 @60Hz / 4:4:4 / 8 bit deep color
Standards Compliant with HDMI 2.0b, HDCP 2.2 and CEC
Bandwidth 18Gbps
USB
Supported USB Standard Up to USB 3.0 @ 5Gbps
USB Port Types (1) USB B (Host)
(1) USB C (Host)
(2) USB A (Client)
Audio
Supported output formats Analog output: PCM
HDMI Embedded: LPCM 7.1 audio, Dolby Atmos®, Dolby® TrueHD, Dolby
Digital® Plus, DTS: X™, and DTS-HD® Master Audio™ pass-through
Audio Output Balanced Stereo Analog
Audio Output Connector 5 pin Phoenix
Audio Output Impedance 70 Ohms
Frequency Response 20Hz-20KHz
Control
Control Port / Connector (1) 3 Pin Phoenix
Chassis and Environmental
Dimensions (WxHxD) 168 mm x 24.5 mm x 95 mm (6.6 in x 1 in x 3.7 in)
Shipping Weight 245g (.54 lbs.)
Operang Temperature 0° to +55° C (+32° to +131° F)
Operang Humidity 10% to 90%, Non-condensing
Storage Temperature -20° to +70° C (+14° to +158° F)
Storage Humidity 10% to 90%, Non-condensing
Power, ESD, and Regulatory
Power Supply Input 100V-240VAC / 50-60 Hz
Power Supply Output 24VDC / 2.71A
Power Consumpon 54 was (max)
ESD Protecon 15kV
Product Regulatory FCC, CE, RoHS
Power Supply Regulatory CE, RoHS
Other
Standard Warranty 5 years
Included Accessories Quick Install Guide, Power Supply with US power plug, (1) 3-pin to DB9
RS232 Cable, (1) 5 pin Phoenix connector, (2) Mounng clips with screws
and (4) plasc cushions
Table of contents
Other Liberty Switch manuals
Popular Switch manuals by other brands

D-Link
D-Link DSD-150 - SecureSpot Internet Security... user manual

Freedom9
Freedom9 freeView IP 800 user manual

Avaya
Avaya 4900 Series Installing

Brocade Communications Systems
Brocade Communications Systems DCX-4S quick start guide

Edimax
Edimax ES-5500P Specifications

Dell
Dell X1000 Series Getting started guide

AVGear
AVGear AVG-UHS24 user manual

SMC Networks
SMC Networks ZK2-ZSV-A Series Operation manual

Lightware
Lightware MX quick start guide

Moxa Technologies
Moxa Technologies PowerTrans PT-7728-F-24 Quick installation guide

ScatterBox
ScatterBox POE Series user manual

Western Digital
Western Digital My Net user manual