Life Fitness Club Machine User manual

CLUB SERIES SMITH MACHINE
Part # 7187601
Rev. B Revision:12/4/011
ASSEMBLY INSTRUCTIONS

PARTS LIST
PART #
71851xx
71124xx
71125xx
7185201
7182702
3203002
7185001
7178101
7112601
7104601
KEY
1
2
3
4
5
6
7
8
9
10
QTY
1
1
1
2
2
2
1
2
6
2
KEY
11
12
13
14
15
16
17
18
19
OR
PART #
3102922
3102904
3102807
3102514
6866701
72031xx
7114701
6866601
6866602
6866603
DESCRIPTION
3/8 X 2-3/4” BOLT
3/8 X 3” BOLT
3/8” LOW HEIGHT LOCK NUT
3/8” SAEWASHER
3/8” RH WASHER
LEFT UPRIGHT
LANGUAGEPLACARD LABEL
BLACK RH CAP
WHITE RH CAP
PLATINUM RH CAP
QTY
16
6
20
42
42
1
1
20
22
22
DESCRIPTION
RIGHT UPRIGHT
TOP CROSS BRACE
BOTTOMCROSS BRACE
HOUSING
BAR STOP
1”SHAFT COLLAR
SMITHBAR
BAR SUPPORT RACK
WEIGHT HORN
GUIDE ROD
BOLT LENGTH
Tools Required forAssembly
2
NOTE:BOLTLENGTH ISMEASUREDFROMTHE UNDERSIDEOFTHEHEAD OFTHEBOLT.
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
* Rubber mallet or hammer
* 9/16” wrench
* Ratchet with 9/16” socket
* 3/16”Allen wrench

3
12 3/8 X 3” BOLT
11 3/8 X 2-3/4” BOLT 13
3/8” LOW
HEIGHT LOCK
NUT
14
3/8” SAE
WASHER
18
RH CAP
(BLACK/WHITE/PLATINUM)
15
RH
WASHER
19

4
FIGURE 1
STEP 1:
• LOOSELY assemble the two WEIGHT HORNS (9) and the BOTTOM CROSS BRACE (3) to the RIGHT and LEFTUPRIGHTS (1 &
16) as shown in FIGURE 1 using using four BLACK RH CAPS (18), four RH CAPS (19), four 3/8 X 3” BOLTS (12), eight 3/8”
SAE WASHERS (14), eight 3/8” RH WASHERS (15) and four 3/8” LOW HEIGHT LOCK NUTS (13) as shown in FIGURE 1.
• LOOSELY assemble the TOP CROSS BRACE (2) to theTOP SET of holes of the RIGHT and LEFTUPRIGHTS (1 & 16) as shown
in FIGURE 1 using using two RH CAPS (19), two 3/8 X 2-3/4” BOLTS (11), two 3/8” SAE WASHERS (14) and two 3/8” RH
WASHERS (15) as shown in FIGURE 1.
12 3/8 X 3”
8
3
2
• SECURELY tighten all connections made to up to this point.
1
• LOOSELY assemble the BAR SUPPORT RACKS (8) to the outside of the RIGHT and LEFT UPRIGHTS (1 & 16) as shown in
FIGURE 1 using eight BLACK RH CAPS (18), eight RH CAPS (19), six 3/8 X 2-3/4” BOLTS (11), two 3/8 X 3” BOLTS (12),
sixteen 3/8” SAE WASHERS (14), sixteen 3/8” RH WASHERS (15) and eight 3/8” LOW HEIGHT LOCK NUTS (13) as shown in
FIGURE 1.
9
11 3/8 X 2-3/4”
13
18
15 14
19
12 3/8 X 3”
18
19
19
11 3/8 X 2-3/4”
18
19
19
16

5
FIGURE 2
STEP 2:
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• SECURELY assemble the four WEIGHT HORNS (9) to the RIGHT and LEFT UPRIGHTS (1 & 16) as shown in FIGURE 2 using
using eight BLACK RH CAPS (18), eight RH CAPS (19), eight 3/8 X 2-3/4” BOLTS (11), sixteen 3/8” SAE WASHERS (14),
sixteen 3/8” RH WASHERS (15) and eight 3/8” LOW HEIGHT LOCK NUTS (13) as shown in FIGURE 2.
11 3/8 X 2-3/4”
18
14
15
13
9
1
19
16

6
STEP3:
FIGURE 3
• Insert the shaft of the HOUSINGS (4) into the ends of the SMITH BAR (7) as shown in FIGURE 3.
7
4
!! IMPORTANT !!
REMOVE TAPE FROM BOTH ENDS OFTHE
HOUSINGSAS SHOWN!
DONOT REMOVEPLASTIC TUBESON THISSTEP!
HOUSING

7
STEP4:
FIGURE 4
• Slide one GUIDE ROD (10) through the upper hole in the UPRIGHT (1 & 16) and proceed to slide one 1” SHAFT COLLAR (6)
over the bottom of the GUIDE ROD (10) as shown in FIGURE 4.
• Hook the SMITH BAR (7) onto slots of the BAR SUPPORT RACKS (8).
4
6
10
1
5
• CAREFULLY lower the GUIDE ROD (10) through the HOUSING (4) on the SMITH BAR (7). (NOTE: Allow the GUIDE
RODS (10) to push the plastic insert out the bottom of the HOUSINGS (4). Discard these inserts.)
• Insert the GUIDE ROD (10) into the bottom hole of the UPRIGHT (1 & 16). Repeat this step on the other side.
• CAREFULLY slide one BAR STOP (5) over the end of the GUIDE ROD (10). Hook BAR STOP (5) into the slots of BAR
SUPPORT RACKS (8) as shown.
16
8
7

8
STEP5:
FIGURE 5
• Slide the 1” SHAFT COLLARS (6) up the GUIDE RODS (10) to the bushing of the UPRIGHTS (1 & 16) and SECURELY
TIGHTEN.
SECURELY
TIGHTEN!
10
6
1
16

9
FIGURE 6
STEP6:
• If necessary, apply the FOREIGN LANGUAGE PLACARD LABEL(17) to the PLACARD LABELon the RIGHT UPRIGHT (1) as
shown in FIGURE 6.
17
1
• This equipment is designed to be stable during normal use, however, in order to ensure the saftey of personnel during
potential misuse of the equipment, we strongly recommend that this equipment be securely fastened to the floor of the
facility with 1/2” (12mm) fasteners compatible with the flooring material of the facility.

Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
[phone].
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
PREVENTATIVE MAINTENANCE TIPS
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
10
Thankyou for purchasingthe LifeFitness CLUBSERIES SMITH. Ifunsure ofproperuse ofequipment,
callyour local LifeFitness distributor or callthe LifeFitnesscustomer service department at
[phone].
CAUTION-PLEASE READ
Action DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
CLEAN
Upholstery X
Guide Rods X
Hand Grips X
INSPECT
Visual Overall X
Cables X
Hardware X
Frame X
Hand Grips X
LUBRICATE
Guide Rods X
WARRANTY INFORMATION
10YEARS STRUCTURUALFRAME
3 YEARS PILLOWBLOCKS,PULLEYS,WEIGHTPLATESANDGUIDERODS
1YEAR CABLES
90 DAYS UPHOLSTERY