Life Fitness SM80 User manual

M051-K50-B116 1
8 STACK MULTI-JUNGLE (SM80)
WITH HIGH & LOW PULLEYS
UNPACKING AND ASSEMBLY INSTRUCTIONS

SM80 Unpacking & Assembly Instructions
2
The SM80 comes partially assembled. Follow the steps below to complete the assembly.
WARNING: COMPONENTS OF THE SM80 ARE LARGE AND HEAVY. USE CAUTION
WHEN ASSEMBLING THIS MACHINE.
MATERIALS AND TOOLS REQUIRED FOR ASSEMBLY
1/2”, 3/8”, 5/8” & 9/16”
Socket wrench with
extension
1/8”
hex key wrench 5/8” & 9/16” Combination wrench Pinch bar
You will also need a piano dolly to lift and position the weight stacks and a ladder.
ASSEMBLY TIME
Two people can accomplish this assembly in approximately 2-1/2 hours.

SM80 Unpacking & Assembly Instructions
3
UNPACKING
Follow the steps below when unpacking the components of the SM80.
1. Cut off the shipping wrapper.
2. Remove the parts boxes and shipping boards.
3. Remove the items in the parts boxes. These items are shown in Figure 1.
A. Remove the bolts bag.
B. Remove the parts shown below. Parts that are used to build the SM80 are
described in the section HARDWARE at the end of these instructions.
Figure 1. Parts box contents (box 1 on left, box 2 on right).

SM80 Unpacking & Assembly Instructions
4
ASSEMBLY
Figure 2 shows an assembled SM80.
Figure 2. SM80 main components (seats and cables removed for clarity).
1. Cubes (2)
2. Low row bench (2)
3. Lat bench (2)
4. Connecting beam (1)
5. Lat tops (2)
6. Tricep top (1)
7. 300 lb. Weight stacks (4)
8. 190 lb. Weight stacks (4)
1. Place the two weight “cubes” in their “final resting spots.” The cubes will be
approximately 11’4” apart as shown in Figure 3.

SM80 Unpacking & Assembly Instructions
5
Figure 3. Set the weight stack cubes.
2. Bolt on the teardrop pulleys above the benches (see Figure 4) on both cubes
using two 3/8” x 2-3/4” hex head bolts (used to bolt the cross beam to the cross
members and the adjustable pulley tops to the top beams). Include the 3/8” flat
washer, end cap washers, end caps and 3/8” Nyloc (locknut). Use the bolt
configuration shown in Figure 5. You may wish to use a pinch bar to align the bolt
holes.

SM80 Unpacking & Assembly Instructions
6
Figure 4. Bolt on the teardrop pulleys.
Figure 5. Configuration for 6” bolts.

SM80 Unpacking & Assembly Instructions
7
Figure 6. Configuration for 2-3/4” and 3” bolts.
3. Bolt on the connecting beam (part 4 from Figure 2) using a 5/8” socket with
extension and combination wrench, to the cubes using two of the large 7/16” x 6”
bolts, 7/16” washers, and 7/16” nuts, end cap washers and end caps. Figure 7 shows
the connected cubes.
7/16” x 6” (8)-
mount on tops
3/8” x 3” (4)-
bolt top
beams together
T
T
U
U
Remove pulleys from
housings to give clearance
to socket extension
Figure 7. Bolt on the connecting beam, lat tops, tricep tops.
4. Mount the 56” lat tops (part T) to the cells using a 5/8” socket and combination
wrench by inserting two of the large 7/16” by 6” bolts using the hardware configuration
shown. Mount the 29” tricep tops (part U) to the frame and connecting beam (See
Figure 7). Use the hardware configuration shown. You will need to remove the pulleys
from the teardrop pulley assemblies to gain clearance for the socket wrench
extension. Leave the pulleys out of the housings until the cables have been installed.

SM80 Unpacking & Assembly Instructions
8
Figure 8. Mount rubber bumpers and the weight stacks.
5. Install the weight stacks. To do this:
A. Using a 9/16” socket and combination wrench, remove the tricep back rest bolts
(see Figure 9).
B. Using a 9/16” socket and combination wrench, unbolt the top plate and remove
the guide rods (see Figure 9).
Figure 9. Remove the tricep back rest, the top plate and the guide rods.

SM80 Unpacking & Assembly Instructions
9
C. Prepare the weight stack. Slide the guide rods (2) through the weight stacks (1)
as shown below. Place rubber bumpers (3) on the bottoms of each guide rod.
Make sure the pull pin (4) is in the bottom weight plate.
D. Flip over the weight stacks. When shipped, the weight stacks have the pull pins
facing upward. You will need to flip the stacks over so that the pull pins are facing
outward when they are loaded onto the machine. Since the pull pins will be facing
downward when they are flipped over, it is recommended that you put the stacks
on a padded carpet to keep the pins from being damaged.
E. Set the weight stacks onto the machine. Using a piano dolly, lift the weight
stacks over the bottom plate and set the stacks onto the rubber bumpers with the
plate numbers facing outward. The 300 lb weight stacks need to be facing the
“sides” of the cells (where the benches will be attached- number 8 in Figure 9).
The 190 lb weight stacks will need to be facing the “outsides” and “insides” of the
cells (where the tricep pulleys and crossover pulleys will be attached- number 9 in
Figure 8). Make sure the pull pins are facing outward.
C. Prepare the weight stack-
add bumpers to bottom, insert
guide rods, put pull pin in
bottom stack. D. Flip over the weight stack
onto piano dolly. E. Hoist the weight
stack onto the machine.
Figure 10. Install the weight stacks.
F. Bolt on the top plate to the top of the cells with the top plate on the guide rods
as shown in Figure 11 using a 9/16” socket and combination wrench and the 3”
bolts (with cap washers) that were previously inserted.
Figure 11. Bolt on the top plate.

SM80 Unpacking & Assembly Instructions
10
6. Bolt the floating pulleys into the 190 lb weight stacks used for the crossovers
using a 7/8” combination wrench. You will need to remove the pulley from the housing
to thread the plug into the weight stack bayonet. Make sure the 9/16” jam nut is
threaded 1-5/8” away from the pulley as shown in Figure 12. Leave the pulleys out
since you will need to have them out when the cable is routed.
Figure 12. Bolt the floating pulleys into the crossover 190 lb weight stacks.
7. Mount the seated row and lat benches to the frame. Using the bolts specified in
Figure 14 and a 9/16” socket and combination wrenches, mount the benches as
shown in Figures 13 and 14.