LIFESTYLER 8.0 EXP User manual

®XP
0-8MPH* 2.0HP* STEPINCLINE• PROGRAMMABLESPEED
Model No, 831.297241
Serial No.
The sedal numbercan be found in the
locationshownbelow. Write the serial
number in the space above.
Serial Number
Decal
_kCAUTION!:
Read all safety precautions and
Instructions In this manual
before using this equipment.
Keep this manual in a safe place
for future reference.
OWNER'S MANUAL
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179

iiiiii ii ii
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, when proper assembly and maintenance procedures detailed in
the Owner's Manual are followed, SEARS will, free of charge, repair or replace and install a replacement
part for any defective part, when this treadmill is used in a normal manner.
This warranty does not apply when this treadmill is used for commercial or rental purposes.
SERVICE IS AVAILABLE SIMPLY BY CONTACTING YOUR NEAREST SEARS SERVICE CEN-
TER/DEPARTMENT IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA,
HOFFMAN ESTATES, IL 60179
ii ii i iiii iiiii

®EXP
0-8MPH"2.0HP"STEPINCLINE"PROGRAMMABLESPEED
TABLE OF CONTENTS
IMPORTANT SAFETY PRECAUTIONS ......................................................... 4
BEFORE YOU BEGIN ...................................................................... 5
ASSEMBLY .............................................................................. 6
OPERATION AND ADJUSTMENT ............................................................ 7
TROUBLE-SHOOTING AND STORAGE ............................ ........................... 10
CONDITIONING GUIDELINES ............................................................... 12
PART LIST .............................................................................. 14
EXPLODED DRAWING .................................................................... 15
ORDERING REPLACEMENT PARTS ................................................. Back Cover
WARN ING: Before beginning this or any exercise program, consult your physician.
This Is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all Instructions before using. SEARS assumes no responsibility for personal Injury or property dam-
age sustained by or through the use of this product. 3

IMPORTANT SAFETY PRECAUTIONS
WARNING: To reduc_he risk of burns, fire, electric shock or Injury to persons, read the fol-
lowing Important safety precautions and information before operating the treadmill.
1. Position the treadmill on a level surface, with at least 8 feet of clearance behind the treadmill. Do not
place the treadmill near water, outdoors or on any surface that blocks an air opening. Do not operate
where aerosol products are used or where oxygen is being administered.
2. When connecting the power cord (see PLUGGING IN THE POWER CORD on page 7), plug the power
cord dlrecUy Into a grounded circuit capable of carrying 12 or more amps. No other appliance shOuld
be on the same circuit. Keep the power cord away from heated surfaces. If an extension cord is need-
ed, use only a 14-gauge general-purpose cord of five feet or less In length with a three-wire conduc-
tor.
3. Never move the walking belt while the power is turned off. Do not operate the treadmill If the power
cord or plug is damaged, or if the treadmill is not working properly. (See BEFORE YOU BEGIN on
page 5 If the treadmill is not working properly.)
.Wear appropriate exercise clothing when using the treadmill; do not wear loose clothing that could
become caught in the treadmill. Always wear athletic shoes; never use the treadmill with bare feet,
wearing only stockings or in sandals. Athletic support clothes are recommended for both men and
women.
5. Never start the treadmill while you are standing on the walking belt. Always hold the handrail when
exercising on the treadmill.
6. Never allow more than one person on the treadmill at a time. The treadmill should not be used by per-
sons weighing more than 250 pounds.
7. Keep small children away from the treadmill at all times. Never leave the treadmill unattended while it
is running. Always turn off the power when the treadmill is not in use.
8. Never drop or insert any object into any opening.
9. To reduce the possibility of overheating, do not operate the treadmill continuously for longer than 1
hour.
10. The treadmill is capable of high speeds. Adjust the speed slowly to avoid sudden jumps in speed.
11. Use the treadmill only as described in this manual.
12. Always unplug the power cord before performing the maintenance and adjustment procedures
described in this manual. Never remove the safety cover unless instructed to do so by an authorized
service representative. Servicing other than the procedures in this manual should be performed by an
authorized service representative only.
SAVE THESE INSTRUCTIONS
4

BEFORE YOU BEGIN
Thank you for selecting the SEARS LIFESTYLER ®8.0 EXP treadmill. The LIFESTYLER 8.0 EXP treadmillblends
advanced technology with innovative design to let you enjoy an excellent form of cardiovascular exercise in the
convenience and privacy of your home.
For your safety and benefit, read this manual carefully before using the treadmill. If you have additional
questions, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6
a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model num-
ber and serial number before calling. The model number of the treadmill is 831.297241. The serial number can be
found on a decal attached to the treadmill (see the front cover of this manual for the location).
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.
Console Control Knob
Handrail
Safety Key/Clip
FRONT
Foot Incline Knob
Walking Belt
Foot Rails
Power Cord
BACK
Rear Roller
Adjustment Bolts
Circuit Breaker
On/Off Switch
Rear Leg Pad
RIGHT SIDE
Note: The rear leg pad may mark some types of linoleum. Mild household cleaning agents will remove any marks. 5

ASSEMBLY
Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until
assembly iscompleted. THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY: The 7132" allen
wrench _Included and your own adjustable wrench _.
,With the help of a second person, raise the Right Upright (27)
and Left Upright (not shown) to a vertical position. Alignthe
hole inthe lower end of the Right Upright with the hole in the
side ofthe Frame (50). Insert a 3/8" x 3" Bolt (31), with an
Upright Washer (30), intothe Right Upright and tighten the Bolt
into the Frame. Tighten the Boltthat is already inthe Right
Upright.
Attach a Bolt and Washer on the leftside inthe same manner
(not shown). 30 31
,With the help of a second person, rotate the ,Left and Right
Handrails (1, 11) up as shown. Insert two 3/8" x 1 1/4" Bolts
(13) into the Left and Right Uprights (19, 27) and tighten the
Bolts with the 7/32" Allen Wrench (90).
3. Remove the paper backing from the Wrench Clip (21). Press
the Wrench Clip onto the Frame (50) in the indicated location.
Press the 3/16" Allen Wrench (72) intothe Wrench Clip.
Make sure that all parts are tightened before using the treadmill.
Note: To protect the floor, a covering should be placed under
the treadmill.
50
21 _72
6

OPERATION AND ADJUSTMENT
APPLYING SILICONE LUBRICANT
To reduce the friction of the walking belt and minimize wear, a non-
oil-, non-petroleum-base silicone lubricant must be applied to the
walking platform before the treadmill is used. Failure to apply lubri-
cant will reduce treadmill performance. WITH THE POWER CORD
UNPLUGGED, lift each side of the walking belt and spray lubricant
generously onto the indicated area. Reapply lubricant after every
ten hours of use, or whenever performance decreases. Lubricant is
available at most hardware and automotive stores. Uni.SportTM sili-
cone spray is recommended.
Apply lubricant
to the entire
shaded area.
Silicone Lubricant
PLUGGING IN THE POWER CORD
This product must be grounded. If itshould malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock.
This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug the
power cord into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
",._ DANGER: Improper connection of the equipment-grounding conductor can result in a risk of elec-
tric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is proper-
ly grounded. Do not modify the plug provided with the product--if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This product is for use on a nominal 120-volt circuit, and has agrounding plug that looks like the plug illustrated in
Drawing 1.
A temporary adapter that looks like the adapter illustrated in Drawing 2 may be used to connect this plug to a 2-
pole receptacle as shown in Drawing 2 if a properly grounded outlet is not available. The temporary adapter
should be used only until a properly grounded outlet (Drawing 1) can be installed by a qualified electrician. The
green colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground
such as a properly grounded outlet box cover. Whenever the adapter isused itmust be held in place by a metal
screw.
Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified electrician to determine if
the outlet box cover is grounded before using an adapter.
Grounded Outlet Box
Grounding Plug
Grounding Pin
Grounded Outlet
2
Metal Screw /
Outlet Box
Grounding Pin
Grounding Plug
7

DIAGRAM OF THE CONSOLE
The heart of the treadmill isthe state-of-the-art programmable console. The console offers both manual and pro-
gram operation, and features an array of independent LCD displays to give you continuous exercise feedback.
Please read these instructions carefully before operating the console. Note: If there is a sheet of protective
plastic on the face of the console, peel it off before operating the console.
Sfmph ,i O 8 rnph CALORIES D_STANCE
SPEED 11ME
A"l_meSe_ V
I" II I
•_d _ lad talkand;inert
KW.
TURNING ON THE POWER
If the safety key is in the console, remove it. Make sure that the on/off switch located
near the power cord is in the ON position (see the drawing at the right). Plug in the
power cord (see PLUGGING IN THE POWER CORD on page 7). ON
Position
8
Step onto the foot rails of the treadmill. Find the clip attached by a cord to the safety key, and slide the clip onto
the waistband of your clothing.
A,.L CAUTION: Do not stand on the walking belt when turning on the power. Always wear the clip
when using the treadmill; if you fall, the safety key will be pulled from the console, instantly turning off
the power.
Insert the safety key into the console. The four LCD displays will appear. Al! indicators on the console will light in
sequence. When only the manual indicator is lit, the console will be ready for operation.
MANUAL SPEED CONTROL
When the power is turned on, the manual indicator will be lit and the console will be in the manual mode. To start
the walking belt, first turn the manual speed control to "reset." Then, turn the control slowly clockwise until the
walking belt begins to move at slow speed. Note: Each time the walking belt is started, the manual speed
control must first be turned to "reset."
CAUTION: After the manual speed control is turned, there will be a pause before the walking
belt begins to move. Adjust the speed slowly until you are familiar with the operation of the treadmill.
Hold the handrail and step carefully onto the walking belt. Change the speed of the walking belt as desired by
turning the manual speed control. To stop the walking belt, turn the control to "reset."
PROGRAM SPEED CONTROL
When the console is in the program mode, the speed of the walking belt will be controlled automatically by pro-
grams you create. To create a program, first press the MODE button repeatedly to select the WALK mode or the
RUN mode. An indicator will light to show which mode you have selected. If the WALK mode is selected, the
speed range of the walking belt will be about 1 to 4 miles per hour during the program; if the RUN mode is select-
ed, the speed range of the walking belt will be about 2 to 8 miles per hour.

Each program is divided intoeight equal time periods, called segments. The speed of the walking belt willchange
automatically at the beginning of each segment. Aspeed setting should now be programmed for each of the eight
segments, using the eight programmable speed controlson the left side of the console. The control on the far left
isfor the first segment, and the control on the right isfor the eighth segment. Move the controls up or down to
program the desired speed settings. If the WALK mode was selected, refer to the scale above the WALK indica-
tor to program speed settings; ifthe RUN mode was selected, refer to the scale above the RUN indicator. Asam-
ple program is shown at the left. This program will begin with a slow speed setting. The speed wfflthen increase
during the second, third and fourth segments, and gradually decrease during the sixth,seventh and eighth seg-
ments. An infinitevariety of speed settings can be programmed.
Next, press the TIME SET buttons to set the length oftime you want the program to last. Each time one of the but-
tons is pressed, the length of time, shown in the TIME display, willchange by 4 minutes. The buttonscan be held
down to set the length oftime rapidly. The program can be set to last for a minimum of4 minutes, up to a maxi-
mum of 96 minutes.
To startthe program, press the START button. The first segment indicatorwill begin to flash, and after a pause the
walking belt will begin to move at the speed setting ofthe first programmable speed control. The TIME display will
show the time remaining in the program. After one-eighth of the length of time you set has elapsed, the second
segment indicator will begin to flash, and the walking belt will change to the speed settingof the second program-
mable speed control.The program willcontinue in this manner until the length oftime you set has elapsed. The
walking belt willthen slow to a stop.
While the program is in progress, the speed of the walking belt can be changed duringthe current segment, if
desired, by moving the programmable speed control located below the flashing segment indicator.The walking belt
can be stopped while the program is in progress by pressing the MODE button or by removing the safety key from
the console.The console willthen be in the same conditionas if the program had been completed. After the pro-
gram iscompleted, the console can be switched tothe manual mode by repeatedly pressing the MODE button.
CHANGING THE INCLINE
To varythe intensity of your exercise, the inclineof the treadmill can
be changed using the foot inclineknob on the rightfoot rail. Before
changing the incline, stop the walking belt. To increase the
incline, stand with your left foot towards the back of the left foot
rail. Using your right foot, press down the foot incline knob untilthe
desired incline is reached. To decrease the incline, stand with your
left foot towards the front of the left foot rail, and press down the
foot inclineknob untilthe desired incline is reached.
Incline /l _
LCD DISPLAY OPERATION
The four LCD displays provide continuous exercise feedback. The four displays are described below:
CALORIES--This display shows the approximate number of nutritional Calories that you have burned.
DISTANCE--This display shows the total distance that you have walked or run, up to 99.9 miles.
SPEED--This display shows the speed of the walking belt.
TIMEwWhen the console is in the manual mode, this display will show the total time that the walking belt has been
moving. (If the treadmill is run for longer than 99 minutes and 59 seconds, the display will reset to zero and the
treadmill will slow to a stop.) if desired, a time goal can be set. To set a time goal, you must first stop the walking
belt. Next, press the TIME SET increase or decrease button. Each time one of the buttons is pressed, the time
goal will change by 1 minute. The buttons can be held down to set a time goal rapidly. While the walking belt is
moving, the display will count down the time goal. When no time remains, the walking belt will slow to a stop. When
the console is in the WALK mode or the RUN mode, the TIME display will show the time remaining in the program.
Note: The CALORIES, DISTANCE and TIME displays can be reset by removing and re-insertingthe safety key.
TURNING OFF THE POWER
To tum off the power, remove the safety key from the console. Store the safety key in a secure location. 9

TROUBLE-SHOOTING AND STORAGE
Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies,
and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-
800-999-3756, Monday through Friday, 6 a.m. until6 p.m. Mountain Time.
1. SYMPTOM: THE POWER DOES NOT TURN ON
a. Make sure that the power cord is plugged into a properly grounded outlet. (See PLUGGING IN THE
POWER CORD on page 7.) Ifan extension cord is needed, use only a 14-gauge general-purpose cord of
five feet or less in length.
b. After the power cord has been plugged in, make sure that the safety key is fully inserted intothe console.
Various indicators on the console should light. (See OPERATION AND ADJUSTMENT on page 7.)
C, Check the circuit breaker located on the treadmill near the
power cord. If the switch protrudes as shown, the circuit break-
er has tripped. To reset the circuit breaker, wait for five min-
utes and then press the switch back in.
d. Check the on/off switch located on the treadmill near the
power cord. The switch must be in the ON position.
2. SYMPTOM: THE POWER TURNS OFF DURING USE
Tripped
Reset
a. Check the circuit breaker located on the treadmill near the power cord. Ifthe circuit breaker has tripped (see
the drawing above.), wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the safety key from the console. Reinsert the safety key fully intothe console. Various indicators on
the console should light.
d. Check to make sure the on/off switch is in the ON position. (See 1. d. above.)
e. If the treadmill stillwill not run, please call our Customer Service Department.
10
3. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON
a° Apply silicone lubricant to the walking platform before use. Reapply lubricant after every 10 hours of use,
and whenever a decrease in performance is noticed. (Uni.Sport silicone spray is recommended.) CAU-
TION: UNPLUG THE POWER CORD WHEN APPLYING LUBRICANT. (See OPERATION AND ADJUST-
MENT on page 7 for application instructions.)
b. Ifan extensioncord is needed, use onlya14-gaugegeneral-purpose cordoffive feet or lessin length.
c. If the walking belt is overtightened, treadmill performance may
decrease and the walking belt may be permanently damaged.
Remove the safety key and UNPLUG THE POWER CORD.
Using the 3/16" allen wrench, turn both rear roller adjustment
bolts coun|erclockwise, 1/4 of a turn. When the walking belt is
properly tightened, you should be able to lift each side of the
walking belt 3-4 inches off the walking platform. The center of
the walking belt should just touch the walking platform. Be care-
ful to keep the walking belt centered. Plug in the power cord,
insert the safety key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened. Rear Roller Adjustment Bolts

4. SYMPTOM: THE WALKING BELT IS OFF-CENTER OR SLIPS WHEN WALKED ON
a. If the walking belt has shifted to the left, first remove the safety
key and UNPLUG THE POWER CORD. Using the 3/16" allen
wrench, turn the left rear rolleradjustment bolt clockwise, and
the rightbolt counterclockwise, 1/4 of a turn each. Be careful not
to overtighten the walking belt. Plug in the power cord, insert the
safety key and run the treadmill for afew minutes. Repeat until
the walking belt is centered.
b. If the walking belt has shifted to the right,first remove the safety
key and UNPLUG THE POWER CORD. Using the 3/16" allen
wrench, turn the left rear roller adjustment bolt counterclockwise,
and the rightbolt clockwise, 1/4 of a turn each. Be careful not to
overtighten the walking belt. Plug iil the power cord, insert the
safety key and run the treadmill for afew minutes. Repeat until
the walking belt is centered.
b
C, If the walking belt slipswhen walked on, first remove the safety
key and UNPLUG THE POWER CORD. Using the 3/16" allen
wrench, turn both rear roller adjustment boltsclockwise, 1/4 of a
tum. When the walking belt iscorrectly tightened, you should be
able to lifteach side of the walking belt 3-4 inches off the walking
platform. The center ofthe walking belt should just touch the
walking platform. Be carefulto keep thewalking belt centered. Plug
in the power cord, insert the safety key and run the treadmill for a
few minutes. Repeat untilthe walking belt ispropedytightened.
STORAGE
Unplug the power cord when the treadmill is not in use. Remove the
indicated bolt and washer from the lower end of each upright. Loosen
the other bolts in each upright.Carefully rotate the uprightsdown. It is
recommended that the treadmill be covered during extended periods
of storage.
11

CONDITIONING GUIDELINES
The following guidelines will helpyou to plan your exercise program. Remember that proper nutrition and ade-
quate rest are essential for successful results.
^A,LWARNING: Before beginning this or any exercise program, consult your physician. This is
especially important for individuals over the age of 35 or individuals with pre-existing health problems.
EXERCISE INTENSITY
To maximize the benefits of exercising, it is important to exercise with the proper intensity.The proper intensity
level can be found by using your heart rate as a guide. For effective aerobic exercise, your heart rate should be
maintained at a level between 70% and 85% of your maximum heart rate as you exercise. This is known as your
training zone. You can find your training zone in the table below. Training zones are listedfor both unconditioned
and conditioned persons according to age.
AGE
20
25
30
35
40
45
50
UNCONDITIONED
TRAINING ZONE
(BEATS/MIN)
138-167
136-166
135-164
134-162
132-161
131-159
129-156
CONDITIONED
TRAINING ZONE
(BEATS/MIN)
133-162
132-160
130-158
129-156
127-155
125-153
124-150
UNCONDITIONED CONDITIONED
TRAINING ZONE TRAINING ZONE
AGE (BEATS/MIN) (BEATS/MIN)
55 127-155 122-149
60 126-153 121-147
65 125-151 119-145
70 123-150 118-144
75 122-147 117-142
80 120-146 115-140
85 118-144 114-139
During the first few months ofyour exercise program, keep your heart
rate near the low end of your training zone as you exercise. After a few
months, your heart rate can be increased gradually until itis near the
middle of your training zone as you exercise. To measure your heart rate,
stop exercising and place two fingers on your wrist as shown. Take a six-
second heartbeat count, and multiplythe resultby 10 to find your heart
rate. For example, if your six-second heartbeat count is 14, your heart
rate is 140 beats per minute. (A six-second count is used because your
heart rate will drop rapidlywhen you stop exercising.) Adjust the intensity
of your exercise untilyour heart rate is at the proper level.
WORKOUT GUIDELINES
Each workout should consist ofthree basic pads: a warm-up, 20 to 30 minutes of trainingzone exercise, and a
cool-down. Warming up prepares the body for exercise by increasing circulation, delivering more oxygen to the
muscles and raisingthe body temperature. Begin each workout with 5 to 10 minutes of stretching and light exer-
cise to warm up. Then, increase the intensity of your exercise to raise your heart rate to your training zone for 20
to 30 minutes. Breathe regularly and deeply as you exercise--never hold your breath. Finish each workout with 5
to 10 minutes ofstretching to cool down. This will increase the flexibility of the muscles, and reduce soreness and
other post-exercise problems.
To maintain or improve your condition, complete three workouts each week, with at least one day of rest between
workouts. After a few months of regular exercise, you may complete up to five workouts each week, ifdesired.
The key to success is CONSISTENCY.
12

SUGGESTED STRETCHES
The following stretches can provide a good warm-up or cool-down. Correct form for each stretch is shown in the
drawings below. Move slowly as you stretch--never bounce.
TOE TOUCH STRETCH
Stand with your knees bent slightlyand slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times.
Stretches: Hamstrings, back of knees and back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs.
Stretches: Hamstrings, lower back and groin.
CALF/ACHILLES STRETCH
With one leg in front ofthe other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward and
move your hips toward the wall. Hold for 15 counts, then relax.
Repeat 3times for both legs. To cause further stretching of the
achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for both legs.
Stretches: Quadriceps and hip muscles.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold
for 15 counts, then relax. Repeat 3 times.
Stretches: Quadriceps and hip muscles.
13

PART LIST---Model No. 831.297241 mo94A
Key Part Key Part
No. No. Qty. Description _No. No. Qty. Description
1120786 1 Left Handrail 56 106334 2 Cotter Pin
2116926 2 Cable Tie 57 012149 3Leg Nut/Motor Pivot Nut
3 111869 8 Cage Nut 58 120909 1 Choke Bracket
4 120718 1 Console 59 013547 3 Leg Bolt/Motor Tension Bolt
5 120803 1 Speed Control Knob 60 118202 1 Shock Release
6 120065 1 Long Wire Harness 61 119919 1 Incline Cable
7 114001 1 Console Plate 62 110407 1 Rear Leg Pad
8 013141 4 Console Screw 63 013028 4 Rear Endcap Screw
9 113203 2 6" Cable Loom 64 119431 1 Right Rear Endcap
10 119038 1 Safety Key/Clip 65 120867 2 Lock Nut
11 120787 1 Right Handrail 66 122282 1 Incline Knob Bracket
12 013438 2 Console Bolt 67 116435 1 Incline Lever
13 119994 2 3/8"x 1 1/4" Bolt 68 116434 1 Foot Incline Knob
14 114005 2 Handrail Cap 69 016029 4 4" Cable Tie
15 119429 1 Front Left Endcap 70 016057 4 8" Cable Tie
16 100994 2 Motor Bolt 71 105444 2 Rear Roller Adj. Bolt
17 120066 1 Short Wire Harness 72 045010 1 3/16" Allen Wrench
18 118017 1 Belt 73 014127 3 Roller Adj. Washer
19 120293 1 Left Upright 74 113278 1 Pulley/Flywheel/Fan
20 120445 1 Front Roller Pulley 75 109788 1 Rear Roller
21 016028 2 Wrench Clip 76 119430 '1 Left Rear Endcap
22 120800 1 Right Foot Rail 77 119779 8 Platform Screw
23 119428 1 Front Right Endcap 78 120710 1 Walking Platform
24 109365 1 Choke 79 120711 1 Walking Belt
25 118153 1 Reed Switch/Sensor Wire 80 119935 1 Incline Knob Sleeve
26 120168 1 Extension Wire 81 120801 1 Front Safety Cover
27 120292 1 Right Upright 82 120802 1 Rear Safety Cover
28 112609 1 Front Roller Adj. Bolt 83 120799 1 Left Foot Rail
29 110447 1 Controller 84 120780 2 Deck Shim
30 014132 4 Upright Washer 85 120713 1 Motor
31 112001 4 3/8" x 3" Bolt 86 120785 1 Motor Mounting Bracket
32 113204 2 12" Cable Loom 87 107503 1 Motor Swivel Bolt
33 013162 17 Safety Cover Screw 88 105477 2 Motor Nut
34 118148 1 Belt Guide 89 013510 4 Power Board Screw
35 108080 11 Screw 90 045017 1 7/32" Allen Wrench
36 105989 1 Controller Wire 91 116927 3 Tie Holder
37 120642 1 Electronics Bracket 92 013540 3 Tie Holder Screw
38 019084 1 Grommet 93 014086 5 3/8" Flat Washer
39 109382 1 Circuit Breaker 94 120866 7 Small Screw
40 119163 1 On/Off Switch 95 104188 2 Flat Washer
41 031229 1 Power Cord 96 054023 2 Wire Clip
42 117806 2 Wheel Bolt 97 120630 2 Choke Screw
43 052014 2 Front Wheel 98 122137 2 Handrail Bolt
44 119026 1 Power Cord Bracket # 102634 1 Ground Wire
45 012056 2 Wheel Nut # 107771 1 Power Cord-Power Board Wire
46 119416 1 Safety Cover Bracket # 118201 1 Red Motor-Controller Wire
47 118650 1 Incline Leg # 102246 1 White Power Board-Frame Wire
48 120716 1 Power Board # 101898 1 Breaker-Power Board Wire
49 119502 4 Plastic Spacer # 112083 1 Blue Controller-Motor Wire
50 NSP 1 Frame # 109407 1 On/Off Switch-Breaker Wire
51 112669 2 Shock Pin # 101897 1 14" White Wire, 2 Female
52 118569 1 Shock Bracket # 114011 1 4" Black Wire, Male-Female
53 116768 1 Shock Cushion # 118204 1 8" Blue Wire, Male-Female
54 122002 1 Incline Shock # 122139 1 Owner's Manual
55 114270 2 Shock Spacer
14 Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
for information about ordenng replacement pads.

EXPLODED DRAWING---Model No. 831.297241 mO94A
14
98 18
24
58
3
16
4
13
90
93
31 20 :
98
15
8
11
26
8
28
,-93
83 82 81
79 "17
76 /80 34
/
51
49
54
f
I
30
31
6
41
15

ORDERING REPLACEMENT PARTS
Each TREADMILL has itsown MODEL NUMBER. Always mention this MODEL NUMBER when requesting ser-
vice or repair parts for your TREADMILL.
All parts listed herein can be ordered through SEARS, ROEBUCK AND CO. SERVICE CENTERS and most
SEARS RETAIL STORES. If parts you need are not stocked locally, your order will be transmitted to a SEARS
PARTS DISTRIBUTION CENTER for handling.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
1. The MODEL NUMBER of the product (831.297241).
2. The NAME of the product (SEARS LIFESTYLER ®8.0 EXP).
3. The PART NUMBER of the part(s) from page 14 of this owner's manual.
4. The DESCRIPTION of the part(s) from page 14 of this owner's manual.
Your SEARS TREADMILL has added value when you consider that SEARS has service units nationwide, staffed
with SEARS trained technicians specifically trained on SEARS products, having the parts, tools and equipment to
ensure that we meet our pledge to you: "We service what we sell."
Should you ever need repair service or parts, call toll free:
For repair service: 1-800-4-REPAIR (1-800-473-7247)
For repair parts: 1-800-FON-PART (1-800-366-7278)
Part No. 122139 R1094A Printed in USA © 1994 Sears, Roebuck and Co.