Lifetime TIDAL 90802 User manual

QUESTIONS?
ASSEMBLY INSTRUCTIONS
MODEL #60091
INFLATABLE STAND-UP
PADDLEBOARD
MODEL 90802
TOOLS REQUIRED
Save this instruction in the event the
manufacturer needs to be contacted.
TABLE OF CONTENTS
NO TOOLS REQUIRED
INCLUDES:
CONTACT LIFETIME®CUSTOMER SERVICE:
Call: 1-800-225-3865
7:00 am–5:00 pm (Monday–Friday) MST
and 9:00 am–1:00 pm Saturday MST
MODEL# AND PRODUCT ID
(you will need both when contacting us)
Model Number: 90802
Product ID:
For Customer Service in Mainland Europe
and the United Kingdom,
E-mail:[email protected]
Live Chat: www.lifetime.com
(click on “Ask An Expert” tab)
Video Instructions:
www.youtube.com/lifetimeproducts
TIDAL
Registration................................2
Safety Instructions............................2
Parts Identifier..................................3
Features & Equipment.......................4
Inflation....................................5
Deflation and Fin Assembly...............6
Repair Kit.........................................7
Paddleboard Operation.....................8
Maintenence.........................13
Warning Sticker...............................14
Warranty...................................15
COPY

2
**For customers outside the U.S. or Canada, please contact the store for assistance.**
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 [phone]
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
**Call, or visit our Web site for Saturday hours**
Most injuries are caused by misuse and/or not following instructions. Use caution when using this system.
To ensure safety, do not attempt to use this product without following the
instructions carefully. Check entire product and inside all packing material for
parts and/or additional instruction material. Before using this watercraft, read the
instructions and identify parts using the identifier in this document. Proper and
complete assembly, use, and supervision are essential to reduce the risk of accident
or injury. A high probability of serious injury exists if this system is not assembled,
maintained, and/or operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE AND WILL VOID WARRANTY.
• Follow any and all warnings and cautions carefully.
• Check Fins for tightness before and during the usage season.
• Inspect the Hull for damage prior to each use.
SAFETY INSTRUCTIONS
LIFETIME’S PROMISE TO YOU:
We invite you to read our privacy policy at www.lifetime.com
REGISTER today!
At Lifetime®, we are committed to providing innovative and quality products. While registering,
you will have the opportunity to give us your feedback. Your input is valuable to us.
• You can also opt in to receive new product notifications or promotions.
• In the unlikely event of a product recall or safety modification, your registration
provides the information we need to notify you directly.
• Registration is fast, easy, and completely voluntary.
Maintaining your privacy is our long-standing policy at Lifetime®. And you can
rest assured that Lifetime®will not sell or provide your personal data to other third
parties, or allow them to use your personal data for their own purposes.
REGISTER YOUR PRODUCT ONLINE AT LIFETIME.COM
1181492 B 3/23/2017
COPY

3
PARTS IDENTIFIER
FAJ (x1)
FAH (x1)
DNT (x1)
FAI (x1)
FAF (x1)
FAE (x1)
ID Description Qty
FAE Paddleboard 1
FAF Travel Bag 1
FAH Repair Kit 1
Case 1
Valve Wrench 1
Adhesive 1
Small Patch 2
Large Patch 2
DNT Detachable Fin 1
FAI Air Pump 1
Air Hose 1
Pressure Gauge 1
FAJ Adjustable 3-piece Paddle 1
PARTS LIST

4
1. Valve
2. Bungee
3. Carry Handle
4. D-Ring
5. Detachable Fin
6. Adjustable 3-piece
Paddle
5
Push-Button
Assembly
(with 5 adjustment
positions)
Push-Button
Assembly
6
2
1
3
4
FEATURES & EQUIPMENT

5
INFLATION
1
• Roll out the paddleboard on a smooth surface free of loose material.
• Twist off the valve cap. If the valve head is down (fig. 1), push the valve head in and
turn it clockwise until it pops up (fig. 2).
• Do not exceed 15 psi (1 bar) of air pressure.
Do not use an air compressor to inflate the
paddleboard. Any use of an air compressor may
damage the board and will void the warranty.
!
FAI
Valve Cap
Valve Head
Valve Base
Press and Turn
Clockwise 90°
Valve Head Down
(Deflate Position)
Valve Head Up
(Inflate Position)
Top Viewfig. 1–Side View (Cross
Section)
fig. 2–Side View (Cross
Section)
• Assemble the Pump (FAI) by attaching the hose to the pressure gauge, then attach
the pressure gauge to the pump handle (fig. 3).
• Connect the end of the hose to the valve on the Paddleboard (FAE) and inflate until the
gauge shows an air pressure of 15 psi (1 bar). Make sure the valve head remains in
the closed (up) position and tighten the valve cap.
fig. 3–Air Hose, Pressure
Gauge, and Pump Handle
• To use the pump effectively, stand
the pump on firm, level ground.
Place your feet on the foot rests
and pump at a steady pace using
a consistent motion pushing
directly down over the pump shaft.
!
Valve Head

6
DEFLATION
2
• TO DEFLATE THE PADDLEBOARD:
With the valve cap removed, push the valve head down and turn it 90°
counterclockwise so that the valve head remains in the open (down) position.
Press Head Down
and Turn 90°
Valve Head closed
(for inflation)
Valve Head open
(for deflation)
• The Detachable Fin is recommened for
use in deeper water. Do not use this fin
in shallow water, as it could damage the
bottom of the board.
FIN ASSEMBLY
3
• Slide the Detachable Fin (DNT) into position in the fin housing on the bottom of the
Paddleboard. The Fin should point towards the back of the board. Once the Fin is
in place, push the locking pin into place.
• The Fin can be installed on the
paddleboard while inflated or
deflated.
!
!

7
• Before performing any repairs, make sure the Paddleboard is fully deflated and
lies flat.
1. Prepare a round patch no less than 3 inches or 7 cm in diameter.
2. Clean the patch and the area surrounding the leak with alcohol.
3. To contain excess glue, use masking tape to tape off the area around the patch.
4. Apply 3 thin, even coats of repair kit adhesive to both the surface of the board
and the patch. Wait 5 minutes between each coat.
5. After the third coat, wait 10-15 minutes before applying the patch. Make sure to
apply the patch evenly. Pay special attention to the edges.
6. Wait 24 hours before reinflating.
REPAIR KIT
4
• If an additional repair kit is needed,
contact our Customer Service
Department (see front cover).
!
• In the unlikely event there is an
issue with the valve, the valve
wrench can be used to carefully
remove and retighten the valve.
!

8
PADDLEBOARD OPERATION
5
To mount your paddleboard, start in at least knee-deep water. Stand
alongside the board and place your paddle across the deck of the
paddleboard.
Before you begin, make sure your paddle is 8-10 inches taller than you.
Your paddle has 5 adjustable height settings. By pushing the pins and
sliding the paddle shaft, you can adjust your paddle to the desired height.
Hold the board by the rails and push yourself up into a kneeling position.
PADDLE ADJUSTMENT
MOUNTING THE PADDLEBOARD

9
XSECTION 5 (Continued)
Make sure you are kneeling just behind the center point of the board. The
nose should not pop out of the water and the tail should not dig in.
Keep your hands on either side of the board until you feel stable enough to
slowly stand up. Place your feet where your knees were and stand up one
foot at a time.
MOUNTING THE PADDLEBOARD (Continued)

10
XSECTION 5 (Continued)
Your feet should be parallel, centered between the rails and about hip-width
distance apart. Keep your toes pointed forward with your back straight and
knees slightly bent. Your head and shoulders should be steady and upright.
Try to keep your eye level with the horizon, and avoid staring at your feet.
You should have one hand on the top grip and the other lower on the paddle
shaft.
While you paddle, the angle of the blade should point toward the front of the
board.
PROPER STANCE