Lifetime 6424 Quick start guide

®
5/1/2006
VISIT THE LIFETIME WEB SITE:
WWW.LIFETIME.COM
30” Shed Extension Kit
MODEL #6424
ASSEMBLY
INSTRUCTIONS AND
OWNER’S MANUAL
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
For Assistance, including missing or broken parts,
Call Customer Service at:
1 [phone]
** Do Not Contact the Store **
INSTRUCTION #1012324

®
3/24/2006
VISIT THE LIFETIME WEB SITE:
WWW.LIFETIME.COM
Hillcrest
30” Shed Extension Kit w/ Window
MODEL #6424
ASSEMBLY
INSTRUCTIONS AND
OWNER’S MANUAL
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
INSTRUCTION #1005147
For Assistance, including missing or broken parts,
Call Customer Service at:
1 [phone]
** Do Not Contact the Store **
BEFORE BEGINNING ASSEMBLY
Identify and inventory all parts using the checklist boxes on the Parts List. Keep the
hardware bags and their contents separate. If any parts are missing, call our Customer
Service Department.
**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY**
SAFETY INSTRUCTIONS
Failure to follow these safety instructions may result in serious injury or property damage. Proper and complete
assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability
of serious injury exists if this display is not installed, maintained, or operated properly. • If using a ladder during assembly,
use extreme caution. Follow all warnings and cautions on the ladder carefully. • 2 people are required for assembly. •
Misuse could result in system failure. • If technical assistance is required, contact the manufacturer.
Most injuries are caused by misuse and/or failure to follow instructions.
PARTS LIST
ID Part # Description Qty
108 ZS10882 Wall Panel 1
125 ZS12582 Window Wall Panel 1
110 CB11099 Center Floor Panel 1
114 CB11480E Lower Roof Panel 2
117 CB11780C Center Roof Cap 1
AA CH08580 Skylight 1
AB AR02406 Roof Truss Channels 2
AC 1001866 Roof Truss Brace 1
AD ZS01006 Roof Support 2
AE ZS01200 Window 1
Hardware Bag [1005273]
TA 1001865 Truss Connector 1
TB BB04500 Threaded Rod 1
TD BN00300 1/4” Cap Nut 2
TE BN01600 #10 Cap Nut 6
TF BS06100 #10 x 3/8” Pan-Head Screw 8
TH BS07500 .25” x .625” Screw 45
TI BS05900 #10 x .5” Pan-Head Screw 6
TJ BW01200 #10-1” Fender Washer 6
TK 1007360 Window Latch 2
108
110
114
117
125
AE
TK

4 5
TB
TA
AC
AB
AA
AD
HARDWARE IS ACTUAL SIZE
(unless otherwise indicated)
1. 7/16” Wrenches (2)
2. 3/8” Wrenches (2)
3. #2 Phillips screwdriver or
Electric drill with pillips head
Tools and Materials
Required for Assembly
(Not Included)
TI TJ
TD TF TH TE
If you are Installing a New Shed
1. Check contents of boxes and compare to parts listed on the Parts List.
2. Follow instructions that came with your shed, but add extra floor panel, wall panels, Roof Cap
and Skylight at appropriate points in the assembly.
If you are Extending an Existing Shed
1. Remove any objects from back shelves.
2. Remove any shelves, pegboards, or other objects hanging on the last two Side Wall Panels on
either side.
3. Check contents of boxes and compare to parts listed on the Parts List.
4. Follow the steps in this manual.
5. If you are extending an 8’ x 5’ shed you will need to modify the following instructions by not
removing as many parts as shown in the illustrations.
1
a. Remove last three skylights.
2
a. Remove the back 3 roof caps.
3
a. Remove the back Roof panels and Roof support bars.
**Save all hardware for re-assembly!**

6 7
4
a. Remove the next Roof panels and Roof support bars.
5
a. Remove the Roof Truss.
6
a. Remove the last two Side Wall Panels.
7
a. Slide the back section of the shed away from the front. You
will need to tip the back section forward slightly in order to disconnect
the floor panels
Be sure that there is
nothing on the back
shelves before moving thie
back section.
One person should
support the back wall
while it is being tipped and
moved.

9
9
a. Add new floor panel. Then, slide the back section into place
and connect the floor panels (you will need to tip the panels forward
slightly to connect the panels).
10
a. Add Wall panels.
Insert a wood block directly
under the tab you want to
insert, then slide block to
next tab and repeat.
Tip up one floor panel and line up tabs
and then lay floor panel flat.
a. Remove plastic sheeting from Window (AE) and slide Window
into slot on the Window Wall Panel (125).Attach a Window Latch (TK)
above each corner of the Window as shown. When tightening screws
(TH), be sure that Window Latches will slide freely. Do not overtighten.
Insert screw (TF) into the hole in the window. Set panel aside.
8Assemble Window TH
Insert window with bent edge
at top and pointing away from
the wall.
TK
Place screw (TF) in this hole to keep
window from sliding up too far. Insert
until flush with the window
TF

10 11
b. Use Truss Connector (TA) to attach Roof Truss Channels at top. Secure with screws (TF) and nuts
(TE). Before completely tightening, lay assembly on its side to be sure Channels and Brace are parallel.
Completely tighten all hardware.
11 Assemble Truss
a. Attach Brace (AC) to two Roof Truss Channels (AB) (one on
each side of Brace. Secure Brace with screws (TF) and nuts (TE).
Be sure that Truss Connector
is aligned with the Truss
Channels.
Follow picture above to connect
Brace to a Truss Channel at each
end of the Brace.
TE
TF
The nut goes on
outside of the truss.
c. Slide a Threaded Rod through the Truss
Support Brace and the top of the Truss Connector. TD
d. Secure the top and bottom of the Threaded Rod with a 1/4” Cap Nut (TD).
TB
TB

12 13
12
a. Add Truss.
13
a. Add Roof panels and Roof
Supports.
b. Add a center Roof Cap.
Roof Panel Ridge
Roof Panel
Wall
14
a. Add Truss.
15
a. Add Roof panels and Roof
Supports.
b. Add a center Roof Cap.

14 15
b. Add the last Center Roof Cap and the End Roof Cap.
16
a. Add Roof panels and Roof
Supports.
17
a. Add Skylights
Congratulations on your Lifetime®Outdoor Shed purchase. By following the instructions
below, your new Lifetime shed should provide you with years of service and enjoyment.
Cleaning and Care
The polyethylene walls and shelves are stain- and solvent resistant. To clean, use a mild soap and a soft-bristled
brush. Abrasive cleaning materials may scratch the plastic and are not recommended. Repair scratches or rust
spots on the metal by Sanding the affected area lightly; using a rust preventative spray primer; and finally, spraying
with a high-gloss spray enamel paint. Avoid placing a direct heat source on or near surfaces unless using a heat
barrier.
For warranty details or to register your product, visit
www.lifetime.com or call 801-776-1532
Model #
0110 Corner Shelf (2 pack)
Two 10” radius shelves with hardware.
0130 32” Shelf Kit w/ hardware (3 pack)
Three 32” x 10” Steel-Reinforced Shelves with shelf brackets and
hardware.
0150 8’Shelf Kit w/ hardware
One 96” x 9” Steel-Reinforced Shelf with shelf bracket and hardware.
0170 Pegboard w/ hardware
One 22.5” x 22.5” Pegboard Panel with hooks. Great for hanging large
and small items such as: rakes, shovels, and hand tools.
0190 Shelf Support Channel
Two Shelf Support Channels that allow the 32” shelves on either of the
side walls of your shed.
Enhance your Lifetime®Outdoor Shed by purchasing the
following Shed Accessories:
Or call:
1 [phone]
To purchase shed accessories,
visit us at:
www.buylifetime.com
0110 0130 0150 0170