Lifetime 73729 Quick start guide

1
®
4/17/2012
ASSEMBLY INSTRUCTIONS AND
OWNER’S MANUAL
WARNING
Failure to comply with any of the warnings in
these instructions may result in serious personal
injuries such as cuts, broken bones, nerve
damage, paralysis, brain injury, or death. Failure
to comply may also result in property damage.
Please heed all warnings and cautions. To
ensure your safety, do not attempt to assemble
this system without reading and following all
instructions carefully. Identify and inventory the
parts using the Parts List.
**For U.S. and Canada Customers ONLY:**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!!!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 [phone]
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (MST)
Call, or visit our Web site for Saturday hours
**Customers outside the U.S. or Canada, please contact the store.**
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
INSTRUCTION #1030954 D
**A MINIMUM OF TWO ADULTS ARE
REQUIRED FOR ASSEMBLY**
BACKBOARD AND RIM COMBO
MODEL #73729
www.lifetime.com
COPY

2
PARTS LIST
ID Part # Description Qty
AA 825619 Rim 1
AB 1030889 Backboard 1
AC 502005 Net 1
AD 502056 Plastic Guard 1
AE 800165 Rim Cover Plate 1
AF CB08999 Corner Frame Pad 2
AG CB09099 Center Frame Pad 1 AH
804018 Rim Pivot Bracket 1
AI 804033 Spring Retainer Plate 1
Rim Hardware (HD9136B)
RA BS01000 #7 x 3/8” Screw 4
RC 300106 5/16” x 2” Carriage Bolt 2
RD 300114 5/16” Push Nut 2
RE 302011 5/16” x 1 1/4” Carriage Bolt 2
RF 302014 5/16” Flat Washer 2
RG 302061 5/16” x 5” Hex Bolt 2
RH 302090 5/16” Nylock Flange Nut 6
RI 502060 Compression Spring 2
RJ 510038 3/8” x 5 1/2” Axle 1
Frame Pad Hardware (HH00700)
FA BS00100 #10 x 7/8 Self Drilling Screw 10
RA
1. Adjustable Wrench
2. 1/2” Wrenches (2)
3. Electric Drill
4. 1/2” Socket Wrench
HARDWARE IS ACTUAL SIZE
(Unless otherwise indicated)
SAFETY INSTRUCTIONS
RC RD RE RF RG
RH
Failure to follow these safety instructions may result in serious injury or property damage and will void the warranty. The owner must ensure that all
players know and follow these rules for safe operation of the system.
tProper and complete assembly, use, and supervision is essential for proper operation and to reduce the risk of accident or injury.
A high probability of serious injury exists if this system is not installed, maintained, or operated properly.
t*GVTJOHBMBEEFSEVSJOHBTTFNCMZVTFFYUSFNFDBVUJPO'PMMPXBMMXBSOJOHTBOEDBVUJPOTPOUIFMBEEFSDBSFGVMMZ
t5XPQFPQMFBSFSFRVJSFEGPSBTTFNCMZ
t$MJNBUFDPSSPTJPOPSNJTVTFDPVMESFTVMUJOTZTUFNGBJMVSF
t*GUFDIOJDBMBTTJTUBODFJTSFRVJSFEDPOUBDUUIFNBOVGBDUVSFS
Most injuries are caused by misuse and/or failure to follow instructions. Use caution when using the system.
1. The Backboard can be mounted to any Lifetime Products®brand pole or most other commercially available poles. If using other
than a Lifetime Products®QPMFUIFNPVOUJOHCSBDLFUEFTJHONVTUQSPWJEFBEFRVBUFTVQQPSUCFIJOEUIF3JNNPVOUJOHIPMFT
BTXFMMBTUIFVQQFS#BDLCPBSENPVOUJOHIPMFT*GBEFRVBUFTVQQPSUJTOPUQSPWJEFEUIF#BDLCPBSENBZCFEBNBHFEBOE
the warranty will be void. Lifetime Products, Inc.®offers a pole system with a height adjusting mechanism that can be used to
safely mount this Backboard. Please Call Customer Service at the number on Page One for more information.
2. If using an existing pole system that does not include extension arms, or if a pole system is not being used, see Page 8.
FA
*Not all Hardware will be used.
Tools and Materials Required for
assembly
(Not Included)
COPY

3
BEFORE BEGINNING ASSEMBLY
A. Identify and inventory all parts using the checklist boxes on the Parts List. Keep the hardware bags and their contents separate. If any parts
are missing, call our Customer Service Department.
B. Test fit all Bolts by inserting them into their respective holes. If necessary, carefully scrape away any excess powder coating buildup from inside
the holes. Do not scrape away all of the powder coating. Bare metal may rust.
ATTENTION: This Backboard is not designed for custom installations. The Backboard is
designed for use with a Lifetime Products®Pole Mounting Unit or Universal Mounting
Bracket. If a Pole or Mounting Bracket is being used, mount the Backboard and Rim
using the hardware included with the Pole system or Mounting kit and according
to the directions included with that product. Depending upon which mounting
method is used, you will follow either Option 1 or 2 according to indications on the
next page. The Pole or Mounting Bracket will include a set of Backboard Brackets.
Note: A Universal Mounting Bracket will allow you to install the Backboard to a wall,
roof, or 3 1/2” Pole.
NOTE: Do not mount the Rim directly to the Backboard. The strike plate on
the Backboard is not designed to hold the weight of the Rim, and will not be
able to support it. If you need to mount the Rim to the Backboard without
using a Pole system or Universal Bracket system, you must place a metal
support plate behind the Backboard. Failure to use a support plate will result
in damage to the Backboard. Support must also be provided at the top of
the Backboard using the Carriage Bolts in the slots as shown on Pages 4
and 5 in these instructions.
WARNING
The Rim and Backboard Combo kit must be mounted and
supported properly. Damage will occur if sufficient Rim
support is not provided.
Register your product online at www.lifetime.com.
Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that
Lifetime will not sell or provide your personal data to other third parties, or allow them to use your
personal data for their own purposes.
We invite you to read our privacy policy at www.lifetime.com
REGISTER today!
"U-JGFUJNFXFBSFDPNNJUUFEUPQSPWJEJOHJOOPWBUJWFBOERVBMJUZQSPEVDUT8IJMFSFHJTUFSJOHZPV
will have the opportunity to give us your feedback. Your input is valuable to us.
You can also opt-in to receive new product notifications or promotions.
In the unlikely event of a product recall or safety modification, your registration provides the infor-
mation we need to notify you directly.
Registration is fast, easy, and completely voluntary.

4
NOTE: The Backboard Brackets shown are Lifetime Products®
models and are for illustration purposes only. If using Brackets
other than the Lifetime Products®models shown here, refer to the
instructions provided with the Brackets.
UB
RC
AH
RH
AD
STEP 1A
Required for this page:
RC
RH
(4)
(2) OPTION 1 THIS OPTION IS FOR USE WITH BACKBOARD BRACKETS AND A U-BOLT.
ASSEMBLE THE U-BOLT (PROVIDED WITH THE BACKBOARD BRACKETS) TO THE BACKBOARD BRACKETS ACCORDING TO THE INSTRUCTIONS PROVIDED
IN THE POLE OR MOUNTING BRACKET UNIT.
If you have Backboard Brackets that come with a U-Bolt,
use Option 1 and the U-Bolt provided with the Brackets. If
the Backboard Brackets don’t include a U-Bolt, use Option
2 instead.
U-Bolt
Backboard
Brackets
Lay the Backboard (AB)
on a table or bench.
The U-Bolt (UB) goes
through the upper holes in
the Backboard.
Only hand tighten the Nuts (RH) now.
STEP 1B
RE RE RE
Slide the Carriage Bolt (RE) into
the crimped slot in each Back-
board channel.
RH
RH
Bend the Backboard Brackets out
so the lower holes go over the Car-
riage Bolts.
Do not overtighten these
Nuts.
LB RB
Completely tighten the Nuts (RH) from
Step 1A.
To finish the assembly, turn to Page 6
STEP 1C
RE
1/2” Wrench
HD9136B
(2)
AB

5
AD
RG
RF
RH
STEP 1A
RC
RG
RF
RH
Required for this page:
HD9136B
(2)
(2)
(4)
(2)
RC
AH
OPTION 2 THIS OPTION IS FOR ASSEMBLY WITHOUT A U-BOLT.
1/2” Wrench
NOTE: The Backboard Brackets shown are Lifetime Products®models
and are for illustration purposes only. If using Brackets other than
the Lifetime Products®models shown here, refer to the instructions
provided with the Brackets.
Lay the Backboard (AB) on a
table or bench.
The 5/16” x 5” Hex Bolts (RG)
go through the upper holes in the
Backboard.
Only hand tighten the Nuts (RH) now.
RE (2)
RE
RE
STEP 1B Slide the Carriage Bolt (RE)
into the crimped slot in each
Backboard channel.
RH RH
STEP 1C
RE
To finish the assembly, turn to Page 6
Bend the Backboard Brackets
out so the lower holes go over
the Carriage Bolts. Do not overtighten these
Nuts (RH).
Completely tighten the Nuts
(RH) from Step 1A.
AB

6
Required For This Page:
1/2” Wrench
3Turn the Backboard over so it faces up.
RI
JN
JN
45
RH RH
AI
Slide the Compression
Springs (RI) onto the legs
of the U-Bolt or Hex Bolts.
6Tighten the Nylock Flange Nuts
(RH) until the Rim is under the
desired tension.
7
RA
AE
RH (2)
RA (4)
HD9136B
Screwdriver
If the unit with the U-Bolt includes
Jam Nuts (pictured actual size
below) they are to be secured onto the ends
of the U-Bolt or Hex Bolts here.
JN
RD (2) Fasten the Rim Cover Plate (AE)
to the Rim (AA) using the #7 x
3/8” Screws (RA).
1/2” Socket
Wrench
Use the 1/2” socket head from the
socket head wrench to press one
Push Nut (RD) onto one end of the Axle
(RJ).
2
RD
RJ
Note: The Push Nut should rest about 1/4” from the end
of the Axle. If the Push Nut slips on too far, continue
sliding it to the other end of the Axle to remove it and try
again.
RD
RJ
AH
AA
RJ
Slide the end of the Axle (RJ) through the Rim (AA) and the Rim Pivot Bracket (AH). Press the
Push Nut (RD) onto the end of the Axle. Use the 1/2” socket head to secure the Push Nut if
needed.

7
8
HH00700
Required for This Page:
FROM THIS POINT ON FOLLOW THE INSTRUCTIONS PROVIDED WITH THE POLE OR
MOUNTING UNIT.
NOTE: FAILURE TO PROVIDE ADEQUATE SUPPORT BEHIND THE BACKBOARD WILL VOID THE PRODUCT WARRANTY. FOLLOW ALL ASSEMBLY INSTRUCTIONS CAREFULLY.
FA
Electric Drill
(10)
AF
Remove the plastic film from the Backboard.
The lip of the Frame Pad overlaps the front of the Backboard.
AF AG
FA
FA
Use an electric drill to insert the Screws.
Attach the Bottom Frame Pad (AG) first.
Align the small line in the back of the Bottom Frame Pad with the seam in the Backboard frame.
AF
AG
AB
AB
Rear view

8
ACCESSORIES AVAILABLE FOR MORE BASKETBALL FUN!
PRODUCT DESCRIPTION MODEL #
Universal Extension Bracket 9594
Intermediate Size Basketball 594201
Ideal for mounting Backboard and Rim
sets to a pole, wall or roof. (Backboard
and Rim not included.)
Universal Extension Bracket #9594
To place orders, use a Master Card or Visa and call our Cus-
tomer Service Department or send check or money order to:
LIFETIME PRODUCTS, INC.
P.O. BOX 160010
BLDG. D-11, FREEPORT CENTER
CLEARFIELD, UT 84016-0010
Call the Customer Service Department
at the number on Page One for prices
and shipping costs.
If mounting the Backboard to a roof mount, wall
mount or existing pole mount that does not have
an extension provided, you must use a Mounting
Bracket Kit designed for this purpose. Lifetime
Products, Inc.®offers a Universal Extension
Bracket, Model #9594, through our Customer
Service Department. Figures A, B and C show the
Bracket mounted to a roof mount, a wall mount
and an existing pole mount. Please see below for
ordering information.
FIGURE C, EXISTING POLE MOUNTFIGURE B, WALL MOUNTFIGURE A, ROOF MOUNT
ROOF MOUNT, WALL MOUNT, EXISTING POLE MOUNT

9
LIFETIME BASKETBALL EQUIPMENT
5-YEAR LIMITED FACTORY WARRANTY
THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE.
1. Lifetime basketball systems are warranted to the original purchaser to be free from defects in material or workmanship for a period of
five years from the date of original retail purchase. The word “defects” is defined as imperfections that impair the use of the product.
Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper
installation, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other
event beyond the control of the manufacturer.
2. This warranty is nontransferable and is expressly limited to the repair or replacement of defective basketball equipment. If the equipment
is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser. Shipping
charges to and from the factory are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal,
installation or replacement of the basketball system or its components are not covered under this warranty.
3. This warranty does not cover scratching or scuffing of the product that may result from normal usage. In addition, defects resulting from
intentional damage, negligence, unreasonable use or hanging from the net or rim will void this warranty.
4. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest
degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this
product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
5. This product is not intended for institutional or commercial use; Lifetime Products, Inc. does not assume any liability for such use. Institutional
or commercial use will void the warranty.
6. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability or fitness for use. Neither
Lifetime Products, Inc., nor any representative assumes any other liability in connection with this product.
ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT.
REPORT PRODUCT DEFECTS IN WRITING TO:
Lifetime Products, Inc., PO Box 160010 Clearfield, UT 84016-0010
or call [phone] M-F 8 a.m. to 5 p.m. MST.
Please include your dated sales receipt and photographs of damaged parts.
To Register Your Product, Visit Our Website at www.lifetime.com
7