Lifetime ACTION GRIP 91330 User manual

TOOLS REQUIRED TABLE OF CONTENTS
BEFORE ASSEMBLY:
• Decide with what to fill the base
(sand is recommended)
• At least 2 people recommended for setup
Pour le français, voir la page 2. Para el español, ver la página 3.
ASSEMBLY INSTRUCTIONS
Model Number: 91330
Product ID:
Icon Legend.........................................................4
Warnings & Notices..............................................5
Pole Assembly......................................................6
Pole-to-Base Assembly.......................................11
Backboard-to-Rim Assembly...............................15
Backboard-to-Pole Assembly..............................19
Parts Identifier...................................................i-iv
Handle Assembly................................................24
Final Assembly...................................................31
Maintenance.....................................................37
Warning Sticker..................................................38
Registration......................................................39
Warranty..........................................................40
(x2)
(x1)
(x1)
(x1)
(x1)
(x1)
(x1)
(x1)
1/2" (≈13mm), 7/16" (≈12mm),
9/16" (≈15mm), 3/4" (≈19mm)
3/16" (≈5mm)
(included)
375 lb (≈170 kg)
1/2" (≈13mm)
(x2)
(x1)
(x1)
ACTION GRIP™
BASKETBALL SYSTEM
MODEL 91330
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
CONTACT LIFETIME CUSTOMER SERVICE:
Dial 1-800-225-3865
QUESTIONS?
For Customer Service in Mainland Europe
and the United Kingdom,
E-mail:[email protected]
Live Chat:
www.lifetime.com/customerservice/home
(Click on “LIVE CHAT” tab)

2
• Indicates the parts required for a section.
• Indicates no parts are required for a section.
• Indicates special heed should be taken when reading.
• Indicates the hardware to be used for a section.
• Indicates the tools to be used for a section.
• Indicates the number of adults required to perform a specific step, e.g., 2, 3, 4, etc.
• Indicates a specifc step is harder to perform.
• Indicates no hardware required for a specific page or section.
• Indicates to use/not use an electric drill for a specific step.
ICON LEGEND
• Indicates the use of a centerlock nut. A nut with this marking will require some eort to tighten. This
hardware was designed with this feature in order to prevent loosening later.
“$#@*%!”
THIS STEP CAN BE DIFFICULT

3
WARNINGS & NOTICES
Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing
material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware
identifier and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the
risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
• If using a ladder during assembly, use extreme caution.
• Two capable adults are recommended for this operation.
• Check base daily for leakage. Leaks will cause system to fall.
• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.
• Minimum operational height is 6 ft 6 in (1,98m) to the bottom of the backboard.
SAFETY INSTRUCTIONS
!
!

4
POLE
1
BCO
Metal parts
1
Scrap wood
ALL (x1)
Warning sticker
ADS (x2)
ABZ (x2)
ABB (x2)
AAF (x2)
ABE (x2)
ABR (x2)
CIH (x2)
ALH (x1)
ALF (x1)
• The bottom pole (ALE) has been designed with
an indent at one end.
9/16" (≈14 mm)
(x2) (x1)
(x1)
(x1)
ALE (x1)

5
• Secure the pole bracket (ALL) to the middle pole (ALF) with the hardware as indicated.
1.1
ALF
ABE
ABE ABR
ABR
Warning sticker
AAF
AAF
Large holes
Small holes
AAF (x2)
ABE (x2)
ABR (x2)
9/16"
(≈14 mm)
(x2)
ABB (x2)
ABB
ABB
ALL

6
• Align the hole in the bottom of the top pole (ALH)
with the slot in the top of the middle pole (ALF).
• Strike the end of the pole assembly on a piece of
scrap wood or cardboard 5–6 times.
1.2 1.3
• The screw only helps to keep the poles
aligned and should be flush with
the washer, but will spin freely once
inserted.
1.2
ADS (x1)
1.3
CIH (x1)
ALH
ALF
ADS
ALH
ALF
CIH
• Do not strike your feet with the pole sections,
as serious injury may occur.
6x
WARNING
The poles must be seated together! Even if the
poles cover the slots before seating, they must be
struck on a hard surface five to six times! Failure
to seat the poles correctly could allow the poles to
separate during use, which could lead to serious
personal injuries or property damage.
!

7
• Secure the middle pole to the bottom pole (ALE) using
the same method as step 1.2.
1.5
ALF
ALE
ADS
ALF
ALE
CIH
• The lip on the bottom pole should be on the
opposite side of the pole assembly as the pole
bracket (ALL).
ADS (x1) CIH (x1)
• Continue seating the poles until the length of the
assembly is no longer than 83 1/2" (≈212 cm).
1.21.4
83 1/2"
(≈212cm)
• The screw only helps to keep the
poles aligned and should be flush
with the washer, but will spin
freely once inserted.

8
• Again, strike the end of the pole assembly on
a piece of scrap wood or cardboard 5–6 times.
Ensure the slots in the poles are covered before
continuing with the assembly.
1.6
ABZ (x2)
• THE SCREWS (ABZ) ARE DESIGNED TO DRILL INTO THE
METAL OF THE UNDERLYING POLE.
For ease of installation, chuck the self-drilling screws directly
into the drill, or use a 3/8" (≈10 mm) hex driver.
ALH
ALF
ALE
ABZ
ABZ
• Secure the poles with self-drilling screws (ABZ).
1.7
6x
• Do not strike your feet with
the pole sections, as serious
injury may occur.
WARNING
The poles must be seated together! Even if the
poles cover the slots before seating, they must be
struck on a hard surface five to six times! Failure
to seat the poles correctly could allow the poles to
separate during use, which could lead to serious
personal injuries or property damage.
!

9
POLE-TO-BASE
2
Metal parts
Plastic parts
BCQ
AAE (x2)
BTS (x1)
ABD (x4) AAO (x2)
EEO (x2)
AMU (x2)
AJM (x1)
(x2) (x1)
3/16 in/po (≈5 mm)
(x2)
AJD (x1)
ALI (x2)
AJN (x1)
DRZ (x1)
1/2 in/po (≈13 mm)

10
• Screw the base cap (AJN) onto the base (AJM) as indicated.
2.1
• If you have trouble with this section, scan the code below to view a video on on its assembly.
• Make sure the rubber gasket is inside the base cap.
Rubber gasket
http://go.lifetime.com/actiongripsection2
AJM
AJN
AJN