Light Bright Formled 9 AUV User manual

Formled 9 AUV
Battery Headlights
User manual
V 1.0!

Light Bright
Formled 9 AUV
Contents
1. Introduction 3
2. Safety Instructions 4
3. Unpacking the device 6
4. Installation 6
5. DMX-Connection 7
6. Mounting the devices 8
7. Control panel 8
8. Operation of the menu 9
9. Use with Wireless Solution Radio 10
10. Emergency Mode 11
11. Channel assignment 11
12. Service and cleaning 12
13. Remote control 13
14. Information 14
15. Battery Notes 15
16. Correct disposal of this product 17
2

Light Bright
Formled 9 AUV
1. Introduction
ATTENTION: For your own safety, please read these operating
instructions carefully before the first use.
This headlight has left our company in best condition. To maintain this condition and to
ensure safe operation, it is absolutely necessary to observe the following safety instructions
and warnings, which are described in this operating manual.
The manufacturer does not accept any liability for damage caused by not following these
operating instructions or unauthorized changes to the device.
Please note that damages caused by manual changes to this device are not covered by the
warranty.
ATTENTION: This device is for professional use only! Protection class IP
65 -Protected against penetration of dust and water jets.
Light Bright does not authorize the use of your equipment in life support
systems. Life-support systems are systems whose purpose is to
maintain or stabilize life and whose defect or malfunction could result in
death or injury.
3

Light Bright
Formled 9 AUV
2. Safety Instructions
CAUTION: Disconnect the device from the power supply before opening
the device. Touching live parts (high voltage) can cause an electric
shock.
Make sure that the mains voltage to be connected is not higher than the voltage indicated on
the type plate. This device should only be operated with the power source specified on the
type plate.
If you are not sure what type of power supply you have, contact your dealer or your power
company.
Always disconnect the appliance from the power supply before cleaning, changing fuses or
replacing parts.
The mains plug must always be accessible after installation of the spotlight. Do not overload
the sockets or extension cords under any circumstances, as this could lead to fire or electric
shock. Do not place any objects on the power cord. Do not install the spotlight in such a way
that people can trip over the power cord or step on it. Make sure that the power cord can
never be crushed or damaged by sharp edges. Check the unit and the power cord from time
to time.
Always leave maintenance work to a qualified technician.
ATTENTION: This light corresponds to protection class I. Therefore this
light must be connected to a mains socket with earthing contact.
Never connect this device to a dimmable power source.
Some smoke and odor may be produced during initial operation. This is a normal procedure
and does not necessarily mean that the unit is defective.
The unit becomes hot during operation. Never touch the device with bare hands during
operation!
When replacing fuses, only use fuses of the same type with identical values. Have fuses
replaced only by a qualified technician.
ATTENTION: EYE DAMAGE! Do not look into the light source for a long
time during operation. This can be harmful to the eyes. Possibly
dangerous radiation.
4

Light Bright
Formled 9 AUV
If the device was exposed to strong temperature fluctuations (e.g. after transport), the device
must not be switched on immediately. The resulting condensation water can damage your
device. Leave the device switched off until it has reached room temperature.
Do not shake or bump the device. Avoid brute force during installation or operation.
When choosing the mounting location, make sure that the device is not exposed to extreme
heat, humidity or dust.
Ventilation openings and slits in the head and foot of the headlamp serve for ventilation. To
ensure reliable operation of the device and to protect it from overheating, these openings
must not be covered.
Never cover the front lens when the headlight is in use.
The openings should never be covered with fabrics or other objects so that the airways are
blocked.
This device must not be operated in an environment without sufficient ventilation.
The device may only be operated when the housing is closed and all screws are tightened.
The device must always be secured with an additional safety device.
Make sure that the area underneath the spotlight is clear during installation, conversion and
dismantling.
ATTENTION: The distance between the light emission and the
illuminated surface must be at least 2.0 meter.
The front lens must be replaced if it is visibly damaged so that its
function is impaired, e.g. by cracks or deep scratches!
To avoid damaging the internal parts of the lamp base, never let sunlight
shine directly into the front lens.
The maximum ambient temperature of 45°C must not be exceeded.
Do not operate the device until you have familiarized yourself with its functions. Prevent
operation by persons who are not qualified to use the device. Most damage is the result of
improper operation!
Please use the original packaging or specially adapted flight cases when transporting the
device.
5

Light Bright
Formled 9 AUV
3. Unpacking the device
Contents of the package: The spotlight, a Powercon True1 connection cable and an IR
remote control.
Open the packaging carefully on the top side and check the headlight and accessories for
possible transport damage. These should be reported immediately to the transport company.
4. Installation
The device comes with a ready made-up Powercon True1 connection cable. Please use only
the supplied cable or a cable of the same type assembled by a specialist. The connection of
the device to the power supply must also be carried out by an authorized specialist.
Connection in Germany/Europe:
Connected loads: voltage 100-240 V, frequency 50 - 60 Hz, power max. 110 VA
The electrical safety as well as the function of the device is only guaranteed if it is connected
to a properly installed protective conductor system. It is very important that this basic safety
requirement is present. In case of doubt, have the electrical installation checked by a
specialist. The manufacturer cannot be held responsible for damage caused by a missing or
interrupted protective conductor (e.g. electric shock)! Only use the device in a completely
assembled state so that no electrical components can be touched. (danger 100-240 V)
If you have observed the listed points, you can plug in the devices or have them connected to
the mains by a specialist.
ATTENTION: The spotlight may light up immediately if standalone
operation is activated or a DMX signal is applied!
Conductor color
Function
Symbol
Brown
Phase
„L“
Blue
Neutral conductor
„N"
Yellow/green
Protective earth
„PE“ ⏚
6

Light Bright
Formled 9 AUV
5. DMX-Connection
The DMX cabling (signal lines) should be done with a 2-wire cable with shielding. We
recommend a DMX cable with 110 Ohm, 2x0,22mm2or 4x0,22mm2. The plugs and sockets
are 3-pin XLR-connectors, which can be purchased in specialized shops.
Pin assignment:
Pin1 = Ground / Shielding
Pin2 = DMX -
Pin3 = DMX +
The spotlight has a DMX-in and DMX-out connection. Now connect the DMX output of your
controller to the first spotlight (Controller DMX-Out -> Spotlight DMX-In). Then connect the
first spotlight with the second spotlight and so on. In some cases it is advisable to plug in a
so called end plug/end resistor (XLR plug with a resistor of 120 Ohm between pin 2 and pin
3). Whether or not an end plug is required depends on various factors, including the cable
lengths used and the number of units. However, as long as there are no problems in the DMX
line, it is not necessary.
7

Light Bright
Formled 9 AUV
6. Mounting the devices
The spotlight can either be positioned or suspended from a truss system. Horizontal
mounting to the truss is also possible.
If you place the unit on the floor, you may only operate the unit on a hard surface, since the
air inlets must remain free!
To hang the unit on a truss system, use only approved carrying and holding devices such as
superclamps or clamps.
Make sure that the truss system on which you mount the device complies with safety
regulations. When using a truss system, always secure the headlamp with a safety device
that complies with the national regulations. Use the safety eyelet on the device for this
purpose.
7. Control panel
The spotlight has a display to show the set parameters and four buttons to adjust them. This
control panel allows you to adjust all the parameters of the spotlight according to your needs.
8

Light Bright
Formled 9 AUV
8. Operation of the menu
9
1. Level
2. Level
3. Level
Remark
Choose Pattern
1. Static Color
R: XXX
Manual control: Red 0 - 255
G: XXX
Manual control: Green 0 - 255
B: XXX
Manual control: Blue 0 - 255
W: XXX
Manual control: White 0 - 255
A: XXX
Manual control: Amber 0 - 255
P: XXX
Manual control: White 0 - 255
Strobe: XXX
Manual control: Strobe 0 - 20
2. Macro Color
Macro Color
< XXX >
Select Macro Color 1 - 16
3. Show Mode
1. AUTO SP: XXX
Auto effect: Speed 1 - 20
2. FADE SP: XXX
Fade effect: Speed 1 - 20
3. SNAP SP: XXX
Snap effect: Speed 1 - 20
4. R-STRO SP: XXX
Red + Strobe effect: Speed 1 - 20
5. G-STRO SP: XXX
Green + Strobe effect: Speed 1 - 20
6. B-STRO SP: XXX
Blue + Strobe effect: Speed 1 - 20
7. A-STRO SP: XXX
Amber + Strobe effect: Speed 1 - 20
4. Sound Mode
No function
Actually there´s no Sound Function
Reserved for several updates
5. User Colors
R: XXX
Manual control: Red 0 - 255
G: XXX
Manual control: Green 0 - 255
B: XXX
Manual control: Blue 0 - 255
W: XXX
Manual control: White 0 - 255
A: XXX
Manual control: Amber 0 - 255
P: XXX
Manual control: White 0 - 255
Bank X/16
Choose User Bank 0 - 16
6. User Run
1. Static Color
Static Color Run
Colors from 5. User Colors
2. Auto Mode
Automatic Run: Speed: 0 - 20
User Settings
1. Channel
DMX512 Channel
< XX -Ch >
DMX Channel Mode select. 7 Ch or 11Ch.
DMX Channels could be looked up at the DMX Chart
2. DMX Adress
DMX Address
< XXX >
Set up the DMX Adress, don´t confirm it
3. Slave Mode
Run
(Slave Mode)
Slave mode: Fixtures do the same as the first Fixture

Light Bright
Formled 9 AUV
9. Use with Wireless Solution Radio
To connect the device to a Wireless Solution Transmitter, make sure RF 2.4 Setting and RF 2.4
Frequency are set to on. After entering the address, stay in this menu item and press the "Pair" button
on your Wireless Solution transmitter.
ATTENTION: To ensure that none of the devices connected in signal series is in master-slave mode,
disconnect the device from the power supply briefly. Thus the device remains on the already paired
frequency and is ready to play.
10
System Settings
1.White Balance
R: XXX
Manual correction: Red 0 - 255. Normal 255
G: XXX
Manual correction: Green 0 - 255. Normal 255
B: XXX
Manual correction: Blue 0 - 255. Normal 255
W: XXX
Manual correction: White 0 - 255. Normal 255
A: XXX
Manual correction: Amber 0 - 255. Normal 255
P: XXX
Manual correction: UV 0 - 255. Normal 255
2. Show Battery
Show Battery
(Yes) /No?
Set up if the Battery is shown in Display or not
3. Display Sleep
Display Sleep
Open
5Sec
10Sec
15Sec
Set up how long the Display is on
4. Dimmer Option
1. Normal
2. Dimmer - 1
3. Dimmer - 2
4. Dimmer - 3
Set up the Dimmer curve
5. Auto Power
Auto Power
(Off) /On?
Set up if auto switch to Battery if the Power is lost
6. IRC Setting
IRC Setting
(Yes) /No?
Choose if the IRC Remote is used or not
7. RF 2.4 Setting
RF 2.4 Setting
(Yes) /No?
Choose if th RF 2.4 is on or off
8. RF 2.4 FREQ
Reciever Pairing
Yes/ (No) ?
Choose if Reciever Pairing is on or off
9. Power Setting
Power Setting
1. High
2. Medium
3. Low
Choose the LED Power Mode
10. Emergency Lamp
Emergency Lamp
Yes/ (No) ?
Choose if the Emergency Mode is on or off
11. DMX Hold
DMX Hold
(Yes) /No?
Choose if the DMX Hold is on or off
Information
Led Temp:
XX.X°C
Display LED Temperature
Work Hours:
161 H
Display Work Hours
Software Version
V. 1. 06
Hardware version
OLED90 6in1
Display Software and Hardware Version
Power on
Display if powered on Accu or Cable

Light Bright
Formled 9 AUV
In addition, the IRC function should be switched offduring wireless operation and the
wireless function should be switched offduring wireless operation, otherwise the headlight
will flicker.
10. Emergency Mode
The Light Bright FormLED 9 has a distinct Emergency Mode, which can be switched on and off in the
device settings (see p. 8.) The Emergency (Light) Mode automatically switches the spotlight to white in
full brightness in case of a power failure. This allows you to take precautions in case of a power failure
and illuminate legal escape and rescue routes. Your staging area will not get dark in this case. Often
event locations and similar facilities also require sufficient emergency lighting for escape and rescue
routes, e.g. by means of battery-powered spotlights.
Attention: In case of a power failure at the device, but continuous DMX - connection to a controller,
the device starts flickering.
11. Channel assignment
Channel
Value
Function
7
11
1
Dimmer
0-255
0-100% Intensity
2
Shutter effect
0-9
Open
10-255
Shutter effect (slow-fast)
1
3
Red
0-255
0-100% Red
2
4
Green
0-255
0-100% Green
3
5
Blue
0-255
0-100% Blue
4
6
White
0-255
0-100% White
5
7
Amber
0-255
0-100% Amber
6
8
UV
0-255
0-100% UV
Macro
0-9
No function
10-29
Color Macro, select color with CH10
30-49
Jump effect, control speed with CH10
Channel
7
11
11

Light Bright
Formled 9 AUV
12. Service and cleaning
ATTENTION: Always disconnect the device from the voltage source
before opening it!
You can clean the spotlight with a brush/cleaning cloth and a vacuum cleaner or compressor
(low speed only).
Take care not to bend or damage any parts during cleaning. Always carry out a function test
after cleaning is complete.
Please use only clean cleaning cloths or brushes and cleaning agents without alcohol to
clean your device. We recommend regular cleaning at least every three months.
Pay attention to damage to the device, parts of the device and the connection cables. If you
notice any damage, DO NOT use the device and take it to an authorized dealer to exclude
dangers by using defective devices and to repair your device professionally.
9
50-69
Fade effect, control speed with CH10
70-89
Ramp Down effect, control speed with CH10
90-109
Red + white strobe, control strobe speed with CH10
110-129
Green + white strobe, control strobe speed with CH10
130-149
Blue + white strobe, control strobe speed with CH10
150-169
Amber+ white strobe, control strobe speed with CH10
170-189
UV + white strobe, control strobe speed with CH10
190-229
Auto Rainbow
230-255
Rainbow Stop
10
Control
0-255
Color selection/ speed control (slow-fast) CH9
7
11
Dimmer Mode
0-19
Linear Dimmer (Normal)
20-39
TV Dimmer Mode (slow)
40-59
Theater Dimmer Mode (slower)
60-255
Architectural Dimmer Mode (slow speed)
Value
Function
Channel
7
11
12

Light Bright
Formled 9 AUV
13. Remote control
Point the infrared remote control in line of sight directly at the infrared sensor installed on the
front of the spotlight. The maximum range is about 8 meters. The remote control functions
are deactivated in DMX and slave mode. Battery for the IR remote control = CR2025.
Blackout
The blackout button is used to turn off all LEDs, regardless of which mode of operation is activated by
the remote control. Pressing the blackout button again will reactivate the previously selected operating
mode.
Auto
"Auto programs 1-6, program selection with +/-.program speed with speed; +/-.brightness with %;
+/-.
Sound
No function
Strobe
Stroboscope, speed with +/-.
Speed
Speed of the auto and fade programs.
Sensitivity
No function
%
Brightness adjustment with +/-.
Fade
Fade programs Auto 1-5, settings as for "Auto".
Manual
Manual color mixing with the keys R/G/B/A/UV/W and +/-.
0-9
Direct selection of color presets 1-9.
13

Light Bright
Formled 9 AUV
14. Information
This device complies with the CE directive:
•in terms of the directive: 2014/35/EU Low Voltage Directive, (Directive
2014/35/EU of the European Parliament and of the Council of 26.02.2014 on the
approximation of the laws of the Member States relating to electrical equipment designed
for use within certain voltage limits)
•in terms of the directive: 2014/30/EU Electromagnetic Compatibility (Directive 2014/30/EU
of the European Parliament and of the Council of 26.02.2014 on the approximation of the
laws of the Member States relating to electromagnetic compatibility)
The device complies with IP65 and is therefore protected against dust and water jets from
any angle according to DIN EN 60529 as of 02.2020.(Germany)
To guarantee the protection against splashing water according to protection class IP65 for
the DMX sockets, the special DMX input and output sockets must be closed correctly with
the IP65 special XLR plugs or the rubber sealing caps must be used for closing. The power
sockets POWER IN and POWER OUT are splash-proof according to IP65 when correctly
plugged in, also when the rubber sealing caps are used correctly.
During operation, it is mandatory to connect the device to a power supply system equipped
with a powerful grounding (Class 1 device according to EN 60598-1). Furthermore, it is
recommended to protect the supply line of the equipment from indirect contact and/or short
circuits with correctly dimensioned residual current circuit breakers.
Only use the device if the room temperature is below 45°C.
Before starting any maintenance on the unit, it must cool down for at least 10 minutes after
disconnection from the power supply to minimize the risk of damage to the electronic
components. For maintenance or repair work on the chips, the device must cool down for at
least another 20 minutes to prevent burning.
14

Light Bright
Formled 9 AUV
15. Battery Notes
1. Keep the battery poles away from conductive objects such as keys, jewelry or other
materials. Otherwise, the battery may be short-circuited, resulting in injury or burns.
2. Never change the polarity of the battery contacts.
3. Keep the battery away from excessive heat and direct sunlight. Do not place it on or in
heating devices such as microwaves, ovens or radiators. Batteries may explode if
overheated.
4. Do not attempt to modify or revise the battery, insert foreign objects into the battery, or
immerse the battery in or contact with water or other liquids. Failure to do so may result in
fire, explosion or other dangerous situation.
5. If battery acid leaks, make sure that it does not get on the skin or into the eyes. If it does,
rinse immediately with clean water and consult a doctor.
6. If any deformation, color change or overheating of batteries occurs during charging or
storage, stop using the device immediately and remove the battery. If you continue to use
the device, battery acid may leak or cause fire or explosion.
7. Do not throw batteries into fire as they may explode. Damaged batteries can also
explode.
8. Dispose of used batteries in accordance with local regulations. Improper use of the
battery can lead to fire, explosion or other dangerous situations.
9. Do not let children or pets chew, suck or suck on the battery. Doing so may cause
damage or explosion.
10. Do not smash or puncture the battery or subject it to high pressure. Doing so may cause
a short circuit or overheating.
11. Do not drop the device or the battery. If the device or battery is dropped, especially onto
a hard surface, it may be damaged.
12. If the standby time of the device is significantly reduced, replace the battery.
13. If the device has a built-in, non-removable battery, do not attempt to remove the battery
as this may damage the device. To replace the battery, take the device to an authorized
service center.
14. As soon as the spotlight is correctly connected to the mains, the internal battery is
charged, which means that the battery is also charged when the spotlight is in operation.
15

Light Bright
Formled 9 AUV
15. The battery charge status is shown in the display both when the device is switched on
and in standby mode.
16. The charging time from 0% charge status to 100% charge status is about 4 hours.
17. The battery runtime at Full On (RGBWAUV to 100%) is about 3 hours, when using single
colors and color change programs the runtime is correspondingly much longer. The
battery life can be extended to up to 24 hours by the power settings with correspondingly
reduced brightness.
18. After about 300 charging cycles (0% - 100%) the battery capacity is still about 70% of the
nominal capacity. The battery may only be replaced with original accessories by an
authorized service center.
19. Do not charge the battery at ambient temperatures below 0°C and above 40°C. This also
means that the battery of the spotlight must be fully charged (100%) if the spotlight is to
be operated on the mains at an ambient temperature below 0°C (ambient temperature in
operation -15°C to 40°C).
20. Fully recharge the battery immediately after discharge. Batteries that are not fully charged
lose capacity and life.
21. Only store the headlight with a fully charged battery.
22. If the spotlight is not used for an extended period of time, fully charge the battery every 6
months.
23. To prolong the life of the battery, it is recommended to recharge the battery as soon as
possible and not to operate it until the energy of the battery is completely used up.
24. The battery life may be shorter than expected when operating in cold environments.
25. Store the headlight in a cool and dry place to allow for optimal storage conditions for the
battery.
16

Light Bright
Formled 9 AUV
16. Correct disposal of this product
(Valid in the European Union and other European countries with waste
separation) This symbol on the product or related documents indicates that
the product must not be disposed of with normal household waste at the end
of its life in order to prevent damage to the environment or personal injury from
uncontrolled waste disposal. Please dispose of this product separately from other waste and
recycle it to promote sustainable economic cycles. As a private customer, you can obtain
information on environmentally friendly disposal options from the retailer from whom the
product was purchased or from the relevant regional authorities. As a commercial user,
please contact your supplier and check any contractually agreed conditions for the disposal
of the equipment. This product must not be disposed of together with other commercial
waste.
17