Light Symphony LS30034FOB User manual

SPECIFICATIONS
Battery 1 x RC2032
Frequency 434.075MHz
Range 300 meters line-of-sight
Safety Rating Extra Low Voltage
Physical 33 x 60 x 10mm
Ambient Temp. 0°C to +40°C
INTRODUCTION
The Light Symphony keyfob remote control provides simple
remote control over your garden lighting.
This manual provides a basic guide to its functions and assumes
your lighting is now installed and fully working. For more
detailed information on the setting up of the system please refer to
the instructions provided with Light Symphony’s other products.
Before using the keyfob please fit a CR2032 battery. The battery
is inserted by removing the 3 screws on the back of the unit and
sliding it into the holder ‘+’ side up.
Please read the section about “System Codes” to reduce the risk
of interference with neighbouring systems.
ISSUE 1.3
COPYRIGHT © PM INTERNATIONAL LTD 2012
KeyFob
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its
packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product
should be disposed of separately from regular household waste streams. It is your responsibility to dispose
of this and other electric and electronic equipment via designated collection facilities appointed by the
government or local authorities. Correct disposal and recycling will help prevent potential negative
consequences to the environment and human health. For more detailed information about the disposal of your old
equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
Changing The Key Fuctions
The keyfob is manufactured in two pre-set versions, as shown below.
4-Zone Master On/Off + 2 Zone
Model LS30034FOB Model LS30032FOB
However, it is possible to convert between these versions by replacing the keys with
the spare button-caps provided. After replacing the button-caps, the new mode must be
programmed by pressing and holding either the two left-hand or right-hand keys
together until the LED lights, as shown below;
OFF ON
1 2
1 2
3 4
(
Press and
hold to set
2-zone mode
OFF ON
1 2
Press and
hold to set
4-zone mode
1 2
3 4
)

KEY FUNCTIONS
1. INDICATOR
The LED indicator shows the handset is transmitting. It will blink blue
when an ON command is sent
2. GARDEN ON / OFF (LS30032FOB model only)
Press to switch all the garden lighting on or off.
3. AREA ON / OFF
Press keys 1 to 4 once to switch an area on (that has been
previously stored). Press keys 1 to 4 again to switch an Area off.
Note, the first press switches an area on, the second switches it off (toggle).
4. COLOUR CONROL
(only possible where suitable lighting is installed)
To change colour just press & hold an Area key.
MODEL MODEL
LS30034FOB LS30034FOB
ISSUE 1.3
COPYRIGHT © PM INTERNATIONAL LTD 2012
‘SYSTEM’ CODE
Light Symphony controllers use a ’System Code’ to prevent interference with
neighbouring systems. Lighting controllers will only respond if their System Code
matches the code set in the keyfob. The keyfob is factory preset to System Code 1.
It is highly advisable to change the System Code for each new project to reduce the
chance of interfering with neighbouring systems.
To select a new System Code from 1 to 32, press and hold the top two buttons together
for a few seconds, until the blue light stays on. Next click the top-left button to set the
new code, where each click is counted e.g. press 4 times to set System Code = 4.
After 5 seconds of not pressing any keys, the blue LED will blink the code back, to
confirm the value that’s been stored. e.g. 4 flashes confirms System Code = 4.
The keyfob’s System Code is automatically adopted by the lighting controllers
(receivers) when a lighting Area (Zone) is programmed.
NOTE: When commissioning a new system always set the Keyfob (or remote
control’s) System Code first. This ensures lighting controllers have a chance to learn
the code during commissioning.
The Keyfob will store the System Code permanently, even if the battery is removed or
runs down.
1 2
3 4
OFF ON
1 2
1
2
3
4 )
LED
1. Press & HOLD the top two
buttons together until blue LED
lights
)
2. Click top-left button 1- 32
times to set the new System Code.