Light4Me VENOM SPOT RING 200W User manual

1
VENOM SPOT RING 200W
INSTRUKCJA OBSŁUGI
USER MANUAL

2
1 SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do not
switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the
case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only
handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell or smell may arise. This is a normal process and does
not necessary mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with
wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced
by the manufacturer of his service agent or a similar qualified person in order to avoid a hazard.

3
2 UNPACKING
Thank you for choosing our LED 200W moving head light. For your own safety, please read this
manual before installing the device. This manual covers the important information on installa-
tion and applications. Please install and operate the fixture with following instructions. Mean-
while, please keep this manual well for future needs.
The LED 200W is made of a new type of high temperature strength of engineering plastic and
cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly fol-
lowing CE standards, complying with international standard DMX512 protocol. It’s available in-
dependently controlled and linkable with each other for operation. And it is applicable for large-
scale live performances, theater, studio, nightclubs and discos.
The 200W Moving head light which features high brightness and stability. Please carefully un-
pack it when you receive the fixture and check whether it is damaged during the transporta-
tion. And please check whether the following items are included inside the box:

4
3 FEATURES & SPECIFICATIONS
Features
·200W High Output White LED
·50,000 hours lifespan and low power consumption
·Beam Angle 15°, focus function
·High light output, LUX8000@5M at White light
·Temperature protect function, when the internal Temperature is up to 40° then the fans
begin to work, when the internal temperature is up to 70°and the brightness reduce half.
·Color Wheel: 7 colors +white, color fine tuning, rotation with variable direction and speed
·1 static Gobo Wheel: 8 gobos +white, wheel rotation and shake
·1 Rotation Gobo Wheel: 6 gobos +white, wheel rotation and shake
·Prism: 3-facet Prism, bi-directional rotatable at variable speeds
·High speed strobe effect with 1-25 flashers per second
·Internal program available
·19/17 DMX Channels USITT DMX-512
·DMX 512, master-slave and sound activated controllable or auto operation
·Colorful LCD display
·Efficient low noise fan cooling system
·PowerCon IN/OUT
·3-pin & 5-pin XLR connectors IN/OUT
·Two 1/4 turn fastening Omega Clamps
·IP 20 protection rating
Specifications
Input Voltage: AC90-260V 50/60Hz
Light Source: 200W High Output White LED with led round 24X0.5W RGB 3-in-1
Control Signal: DMX 512, master-slave and sound activated or auto operation
Control Channel: 19/17 DMX Channels USITT DMX-512
Power Consumption: 315W
Dimensions: 328(L)*220(W)*482(H)mm
Packing size: 365(L)*290(W)*600(H)mm
Net Weight: 13.50kg,Gross Weight: 15.50kg

5
4 PHOTOMETRIC DATA

6
5 OPERATION INSTRUCTIONS
∙The moving head is for spot effect for on-site decoration purpose.
∙Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So
make sure to operate the fixture until it is in normal temperature.
∙This light should be keep away from strong shaking during any transportation or move-
ment.
∙Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
∙Don’t expose the fixture in overheat, moisture or environment with too much dust when
installing it. And don’t lay any power cables on the floor. Or it might cause electronics
shock to the people.
∙Make sure the installation place is in good safety condition before installing the fixture.
∙Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture.
∙Make sure the lens are in good condition. It’s recommended to replace the units if there
are any damages or severe scratch.
∙Make sure the fixture is operated by qualified personnel who know the fixture before us-
ing.
∙Keep the original packages if any second shipments is needed.
∙Don’t try to change the fixtures without any instruction by the manufacturer or the ap-
pointed repairing agencies.
∙It is not in warranty range if there are any malfunctions from not following the user man-
ual to operate or any illegal operation, like shock short circuit, electronic shock, lamp
broke, etc.

7
6 INSTALLATIONS
Cautions: For added protection mount the fixtures in areas outside walking paths, seating ar-
eas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 items the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an ap-
propriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept
at least 0.5m (1.5ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental dam-
age and/or injury in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including amongst oth-
ers calculating working load limits, a fine knowledge of the installation material being used,
and periodic safety inspection of all installation material and the fixture. If you lack these qual-
ifications, do not attempt the installation yourself. Improper installation can result in bodily in-
jury.
Be sure to complete all rigging and installation procedures before connecting the main power
cord to the appropriate wall outlet.
Clamp Mounting: The LED moving head provides a unique mounting bracket assembly that
integrates the bottom of the base, and the safety cable rigging point in one unit (see the illus-
tration below). When mounting this fixture to truss be sure to secure an appropriately rated
clamp to the included omega bracket using a M10 screw fitted through the center hole of the
“omega bracket”. As an added safety measure be sure to attached at least one properly rated
safety cable to the fixture using on of the safety cable rigging point integrated in the base as-
sembly.

8
Regardless of the rigging option you choose for your LED moving head, always be sure to se-
cure your fixture with a safety cable. The fixture providers a built-in rigging point for a safety
cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging
point for the safety cable and never secure a safety cable to a carrying handle.

9
7 DMX-512 CONTROL CONNECTIONS
Connect the provided XLR cable to the female 3-pin XLR & 5-pin XLR output of your controller
and the other side to the male 3-pin XLR & 5-pin XLR input of the moving head. You can chain
multiple moving head together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram below.
For installations where the DMX cable has to run a long distance or is in an electrically noisy
environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps
in preventing corruption of the digital control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3, which is then
plugged into the output XLR socket of the last fixture in the chain. Please see illustrations be-
low.
.

10
8 MENU OPERATIONS
MENU
Address Set [Set Address Numbers]
[DMX]
Run Mode [AUTO] Auto 1- Auto 4
[SOUND]
[MANUAL] Manual Test Function and Operation
Pan reverse
Tilt reverse
Display
Screen Reverse
Setup [Advanced Setting] Channel (19/17CH Select)
Sensitivity (01-100)
Motor zero
Reset
Factory Set
Ver V1
System Information DMX Address
Temperature

11
9 DMX CHANNELS
19/17 channel mode sheet
17CH
19CH
Function
Channel
Value
Description
CH1
CH1
Pan
0-255
0-540°
CH2
CH2
Pan fine
0-255
Pan Fine
CH3
CH3
Tilt
0-255
0-270°
CH4
CH4
Tilt Fine
0-255
Tilt Fine
CH5
CH5
X, Y speed
0-255
From fast to slow
CH6
CH6
LED Dimmer
0-255
From dark to bright
CH7
CH7
LED Strobe
0-7
Turn on
8-250
Strobe from slow to fast
251-255
Turn on
CH8
CH8
7 color +
White
0-15
White Lighting
16-31
Color 1
32-47
Color 2
48-63
Color 3
64-79
Color 4
80-95
Color 5
96-111
Color 6
112-127
Color 7
128-191
CW from slow to fast
192-255
CCW from slow to fast
CH9
CH9
Color effect
0-10
No function
11-209
Color fine tuning
210-255
Color shake from fast to slow
CH10
CH10
8 Static Gobos
+White
0-6
Open
7-13
Gobo 1

12
14-20
Gobo 2
21-27
Gobo 3
28-34
Gobo 4
35-41
Gobo 5
42-48
Gobo 6
49-55
Gobo 7
56-63
Gobo 8
64-70
Gobo 8 shake speed from slow to fast
71-77
Gobo 7 shake speed from slow to fast
78-84
Gobo 6 shake speed from slow to fast
85-91
Gobo 5 shake speed from slow to fast
92-98
Gobo 4 shake speed from slow to fast
99-105
Gobo 3 shake speed from slow to fast
106-112
Gobo 2 shake speed from slow to fast
113-119
Gobo 1 shake speed from slow to fast
120-127
Open
128-191
Gobo Rotate CW slow to fast
192-255
Gobo Rotate CCW slow to fast
CH11
CH11
6 rotation
gobos +White
0-15
open
16-31
Gobo1
32-47
Gobo2
48-63
Gobo3
64-79
Gobo4
80-95
Gobo5
96-127
Gobo6
128-191
Gobo Rotate CW slow to fast
192-255
Gobo Rotate CCW slow to fast
CH12
CH12
Gobo Rotation
0-15
open
16-95
Gobo Fine 0-180
96-135
Gobo Rotating 0-90

13
136-155
Gobo Rotating 0-180
156-175
Gobo Rotating 0-360
176-215
Gobo self-rotating CW from slow to fast
216-255
Gobo self-rotating CCW rotating from slow
to fast
CH13
CH13
Focus
0-255
Gobo hazy to clear
CH14
CH14
Prism
0-63
Open
64-255
Prism In
CH15
CH15
Prism Rotation
0-15
Stop
16-135
Rotate CW slow > fast
136-255
Rotate CCW slow > fast
CH16
LED round ef-
fect
0-25
No function
26-30
Red
31-35
Green
36-40
Blue
41-45
Full color
46-50
Gradual change
51-55
Strobe
56-60
Effect 1
61-65
Effect 2
66-70
Effect 3
71-75
Effect 4
76-80
Effect 5
81-85
Effect 6
86-90
Effect 7
91-95
Effect 8
96-100
Effect 9
101-105
Effect 10
106-110
Effect 11
111-115
Effect 12

14
116-120
Effect 13
121-125
Effect 14
126-130
Effect 15
131-135
Effect 16
136-140
Effect 17
141-145
Effect 18
146-150
Effect 19
151-155
Effect 20
156-160
Effect 21
161-165
Effect 22
166-170
Effect 23
171-175
Effect 24
176-180
Effect 25
181-185
Effect 26
186-190
Effect 27
191-195
Effect 28
196-200
Effect 29
201-205
Effect 30
206-210
Effect 31
211-215
Effect 32
216-220
Effect 33
221-225
Effect 34
226-230
Effect 35
231-235
Effect 36
236-240
Effect 37
241-245
Effect 38
246-250
Effect 39
251-255
Effect 40
CH17
LED round
speed
0-128
Speed CCW from fast to slow
129-255
Speed CW from slow to fast

15
CH16
CH18
self-setting
Program
0-7
No action
8-131
Auto mode
132-255
Sound mode
CH17
CH19
Reset
0-249
No function
250-253
Reset
254-255
No function
10 MAINTENANCE AND CLEANING
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be tightly connected and
must not be corroded.
2) There must not be any deformations on the housing, color lenses, fixations and installation
spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4) The electric power supply cables must not show any damage, material fatigue or sedi-
ments.
Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a regular clean-
ing to the lights.
1) Clean the inside and outside lens each week to avoid the weakness of the lights due to accu-
mulation of dust.
2) Clean the fan each week.

16
3) A detailed electric check by approved electrical engineer each three month, make sure that the
circuit contacts are in good condition, prevent the poor contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use
alcohol solvents.
There are no serviceable parts inside the device. Please refer to the instructions under “Instal-
lation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
WARNING! THE DEVICE MUST NOT BE DISPOSED OF WITH HOUSEHOLD WASTE.
This symbol indicates that this product must not be disposed of with household waste,
according to the EU and your national law. In order to prevent potential damage to the
environment or health, the used product must be recycled. In accordance with current
legislation, unusable electrical and electronic devices must be collected separately at the desig-
nated facilities for recycling, acting on the basis of applicable environmental standards.
Information about used electrical and electronic equipment
The main goal of European and national law regulations is to reduce the amount of waste pro-
duced from used electrical and electronic equipment, to ensure an appropriate level of collec-
tion, recovery and recycling of used equipment, and to increase public awareness of its harm-
fulness to the environment, at each stage of use of electrical and electronic equipment. There-
fore, it should be pointed out that households play a key role in contributing to reuse and recov-
ery, including recycling of used equipment. The user of electrical and electronic equipment –
intended for households – is obliged to return it to authorized collector after its use. However,
it should be remembered that products classified as electrical or electronic equipment should
be disposed of at authorized collection points.

17
POLSKI
1. INSTRUKCJE BEZPIECZEŃSTWA
UWAGA
PROSIMY ZACHOWAĆ OSTROŻNOŚĆ PODCZAS PRACY. PRZY DOTYKANIU PRZEWODÓW MOŻNA
DOZNAĆ PORAŻENIA PRĄDEM.
Urządzenie opuściło fabrykę w dobrym stanie. W celu utrzymania tego stanu, należy stosować
się do ostrzeżeń i informacji zawartych w tej instrukcji.
WAŻNE
USZKODZENIA SPOWODOWANE ZIGNOROWANIEM INSTRUKCJI I UŻYTKOWANIEM PRODUKTU
NIEZGODNIE Z PRZEZNACZENIEM POWODUJĄ UTRATĘ GWARANCJI. PRODUCENT NIE PONOSI
ODPOWIEDZIALNOŚCI ZA SZKODY Z TYM ZWIĄZANE.
Jeśli urządzenie zostało narażone na zmiany temperatury, nie należy włączać go bezpośrednio
po przeniesieniu do pomieszczenia. Nagromadzenie wilgoci może spowodować uszkodzenia
produktu. Należy odczekać aż głowica osiągnie temperaturę pokojową.
Zasilanie urządzenia musi być uziemione, wszelkie połączenia elektryczne muszą być wykonane
przez wykwalifikowaną osobę. Przed podłączeniem należy upewnić się, że napięcie jest zgodne
z zalecanym.
Upewnij się, że przewód zasilający nie jest uszkodzony, w przeciwnym razie należy go wymienić
na nowy.
Zawsze odłączaj głowicę z zasilania jeśli urządzenie nie jest używane lub jest czyszczone. Nigdy
nie odłączaj z prądu ciągnąc za przewód.
Podczas pierwszego użycia może pojawić się odrobina dymu i zapachu spalenizny, jest to nor-
malny efekt. Nie należy się tym przejmować, po kilku użyciach powinien ustąpić.
Nie należy generować projekcji na materiały palne.
Urządzenie nie może być umieszczane na materiałach palnych, takich jak dywany, kartony, itp.
Należy zachować minimum 50cm odległości od ściany, aby zapewnić odpowiedni przepływ po-
wietrza. Upewnij się również, że otwory wentylacyjne nie są zablokowane.
Jeśli zauważysz uszkodzenie obudowy lub przewodu zasilającego należy skontaktować się
z serwisem, nie należy użytkować produktu.

18
2. WYPAKOWYWANIE
Dziękujemy za wybór naszej głowicy. Dla własnego bezpieczeństwa zapoznaj się z instrukcją
przed użyciem. Zawiera ona ważne informacje na temat bezpieczeństwa instalacji i użytkowania.
Instrukcję należy zachować dla przyszłych potrzeb.
Venom Spot Ring został wykonany z wysokiej jakości nowoczesnego i odpornego za wysokie
temperatury plastiku oraz aluminium. Urządzenie zostało zaprojektowane by spełniać stan-
dardy CE oraz współpracować z protokołem DMXX512. Urządzenia można używać pojedynczo
lub w większej ilości. Oświetlenie to bardzo dobrze się sprawdza w wystąpieniach scenicznych,
teatrach, studiach, klubach i dyskotekach.
Po otrzymaniu przesyłki prosimy o szczegółowe sprawdzenie zawartości, czy nie została
uszkodzona I jest kompletna:
1. Głowica
2. Przewód DMX
3. Przewód zasilający PowerCon
4. Uchwyt montażowy
5. Instrukcja obsługi

19
3 CECHY I SPECYFIKACJA
CECHY
·200W biała dioda LED
·50 000 godzin żywotności diody i niskie zużycie energii
·Kąt świecenia 15o, zmotoryzowany focus
·Wysoka wydajność świetlna, 8000LUX@5M przy białym świetle
·Funkcja ochrony przed przegrzaniem, kiedy temperatura osiąga 40oC wentylatory zaczynają
pracować, przy temperaturze 70oC moc promienia zmniejsza się o połowę
·Koło kolorów: 7 kolorów
·
+biały, rotacja w obydwu kierunkach o różnych prędkościach
·Koło statycznych: 8 gobo + open, gobo scroll, gobo shake
·Koło obrotowych gobo: 6 gobo + open, gobo scroll, gobo shake
·Pryzma: 3-ramienna obrotowa
·Stroboskop o dużej częstotliwości 1-25 błysków na sekundę
·Wbudowane programy
·19/17 kanałów DMX
·Tryby pracy: auto, sound, master/slave, DMX512
·Kolorowy wyświetlacz LCD
·Cichy system chłodzenia
·POWERCON IN/OUT
·Uchwyty szybkiego montażu
·Stopień ochrony IP20
SPECYFIKACJA
Zasilanie: AC90-260V 50/60Hz
Źródło światła: główne - 200W biała dioda LED, ring - 24X0,5W RGB 3-w-1
Tryby pracy: DMX 512, master/slave, sound, auto
Kanały DMX: 19/17 DMX
Zużycie energii: 315W
Wymiary: 328(długość)*220(szerokość)*482(wysokość)mm
Waga: 13.50kg, Waga brutto: 15.50kg

20
4 DANE FOTOMETRYCZNE