Lightcloud XDIM User manual

1(844) LIGHTCLOUD
1(844) 544-4825
WE’RE HERE TO HELP:
Welcome
Lightcloud
XDIM/LCB
Phase Dimmer

Hello
The Lightcloud Blue Phase Dimmer can be used to
control the wired standard lighting or wirelessly control
the Lightcloud Blue-enabled lighting, no Gateway or
Hub required. Easily use the up/down paddle to adjust
the dim level or turn lights on/off. Indicator lights
illuminate to reflect current brightness levels and online
status.
Product Features & Specifications
• Voltage: 120V
• Color: Matte White
• Dimming Protocol: Phase-cut
• Max Load (Dimming Capacity):
LED/CFL: 300W
INC/HAL/ELV: 500W
MLV: 400VA
• Warranty:
3-year, limited warranty
• Compatible with a broad
range of high-efficiency loads
• Power monitoring
(neutral wire is required)
• Neutral optional for
retrofit applications
• High/Low end adjustment

Safety Information
WE’RE HERE TO HELP:
1 (844) LIGHTCLOUD
1 [phone]
[email protected]
• To avoid risk of fire and electrical shock, products shall be installed
in accordance with electrical code and regulations.
• Cut off the power at the circuit breaker or fuse before installation.
• If you’re not clear about any content of the instructions, please
consult a licensed electrician.
• To avoid the risk of overheating and possible damage to the
equipment, do not use the product to control a receptacle,
motor-operated appliance or a transformer-supplied appliance.
• This product applies to compatible, dimmable incandescent,
magnetic low-voltage halogen, electronic low-voltage halogen,
CFL and LED products.
• When connecting multiple products with a single dimmer, do not
mix product types. All products shall be either dimmable LED, CFL
or incandescent products. Using the same type of products will
enhance dimmer performance.
• Switch to the leading edge control mode when an inductive load
(i.e., incandescent or magnetic low-voltage halogen) is used.
Switch to trailing edge control mode when a capacitive load
(i.e., electronic low-voltage halogen, CFL or LEDis used.

Parts Included and Tools Needed
1
Parts Included
Jumper Wire
(1 pcs)
Mounting
Screws (2 pcs)
Base Plate
(1 pcs)
5PIN Wiring
Terminal (2 pcs)
2PIN Wiring
Terminal (3 pcs) Connection Wire (5pcs)
Face Plate
(1 pcs)
Dimmer (1 pcs)
Tools Needed to Install the Dimmer
2
• 5mm Philips Screwdriver
• Electrical Tape
• Electrician Knife
• Test Pencil
• Pliers
• Ruler

Basic Operation
1
Replaceable Control Component
• Control Component can detach from
Power/Communication Component.
Power/Communication Component
Control Component

• White indicator light will remain on for 3 seconds. The timeout
and brightness of the indicator lights can be adjusted in the
Lightcloud Blue app.
Basic Operation (cont’d)
Functional Parts
Power Indicator
Power
Indicator
Power Cut
Off Switch
Brightness
Indicator
Off/Down
Paddle
On/Up Paddle
Switch
Reset
Switch
Status
Indicator
• Short Press: Within 0.5 seconds
• Long Press: Over 0.5 seconds
• Double Press: Within 1 second
2
2a

• Turn light off: When the light is on, short press the
Off/Down Paddle once
• Quickly adjust to the lowest dim level: When the light is on
or off, press the Off/Down Paddle 2 times
• Gradually decrease brightness: When the light is on, press
and hold the Off/Down Paddle, the brightness gradually
decreases, until you release it until the brightness reaches
0% or until you release it to stop the brightness change
• Turn light on: When the light is off, short press the On/Up
Paddle once
• Continuously increase brightness: When the light is on,
short press the On/Up Paddle, the brightness increases
until the brightness reaches 100%
• Gradually increase brightness: When the light is on, press
and hold the On/Up Paddle, the brightness will gradually
increase until the brightness reaches the minimum level or
until the On/Up is released
• Quickly adjust brightness: When the light is on or off, press
the On/Up Paddle for 2 consecutive times
Basic Operation (cont’d)
On/Up Paddle
Off/Down Paddle
2c
2b
• F: Forward Phase Control (leading edge control mode)
• A: Auto detect control mode
• R: Reverse Phase Control (training edge control mode)
Switch
2d
Note: after dip switch, please power off and then power on again.

Basic Operation (cont’d) Basic Operation (cont’d)
Brightness Indicator
2h
LED 11
LED 10
LED 9
LED 8
LED 7
LED 6
LED 5
LED 4
LED 3
LED 2
LED 1
Power
Indicator
Brightness
Indicator
• Flash red (1s on/ 1s off): Device is not provisioned
• Steady green: Device is provisioned
2e
Status Indicator Light
2f
• Push in to connect to line voltage
• Pull out to disconnect light voltage
Power Cut Off Switch
2g
• Restoring factory settings: Press and hold the reset switch
until the status indicator light blinks red. The dimmer is now
reset and ready to be paired. (The dimmer is waiting to be
added to the Lightcloud Blue network)
Reset Switch
Note: When pairing to the Lightcloud Blue APP, Bluetooth must
be enabled on the mobile device.

Basic Operation (cont’d)
Multi-Gang Installation Derating
5
Single-Gang
Rating
500W ELV
400VA MLV
400W ELV
300VA MLV
300W ELV
200VA MLV
300 W CFL/LED/
Electronic
self-ballasted
300 W CFL/LED/
Electronic
self-ballasted
300 W CFL/LED/
Electronic
self-ballasted
120 Vac,
60 Hz,
500 W Tungsten
Double-Gang
Rating
Triple-Gang
Rating
120 Vac,
60 Hz,
400 W Tungsten
120 Vac,
60 Hz,
300 W Tungsten
Note: Brightness Indicator lights will stay illuminated while circuit it powered on.
No.
1
2
3
4
Brightness Level
Brightness Level 1
Brightness Level 2
Brightness Level 3
Brightness Level 4
5
Brightness Level 56
7
8
9
10
Brightness Indicator
LED 2
LED 2~LED 3
Brightness Level 9 LED 2~LED 10
LED 2~LED 4
Brightness Level 8 LED 2~LED 9
LED 2~LED 5
LED 2~LED 6
Brightness Level 6 LED 2~LED 7
Brightness Level 10 LED 2~LED 11
Brightness Level 7 LED 2~LED 8

Installing your Lightcloud Blue Device
1Turn off Power
OFF
OFF
WARNING
• Place the wall switch in the off position
If the XDIM dimmer is currently installed, it can be converted
to a XDIM/LCB dimmer, no rewiring required.
2Remove Existing Switch
Remove Existing Switch
Replacing the XDIM dimmer Control
Component
• Remove existing wall panel and switch mounting screws.
• Carefully pull switch from wall box, identify and remove
the wires attached to the switch, then remove the switch.
• Do not remove the wires from the wall at this time.
(for new installations where an existing switch does not
exist, skip this step.)
• Turn off the main power at the breaker
panel or remove the fuse from the fuse box
2a
2b
• Remove the face plate to access the Power Cut Off Switch.
• Pull the Power Cut Off Switch out and remove the XDIM
Control Component.
• Replace it with the Operation Paddle Assembly for the
XDIM/LCB.
• Push in the Power Cut Off Switch.
• Skip to Controlling your Lightcloud Blue Device to continue.