Lightware UMX-TPS-TX100 Series User manual
UMX-TPS-TX120, -TX130, -TX140
WP-UMX-TPS-TX120-US Black, White
WP-UMX-TPS-TX130-US Black, White
FP-UMX-TPS-TX130-MKM
HDBaseTTM Multimedia Extender
User’s Manual
UMX-TPS-TX100 series – User's Manual 2
Important Safety Instructions
Class II apparatus construction.
The equipment should be operated only from the power source
indicated on the product.
To disconnect the equipment safely from power, remove the power
cord from the rear of the equipment, or from the power source. The
MAINS plug is used as the disconnect device, the disconnect device
shall remain readily operable.
There are no user-serviceable parts inside of the unit. Removal of the
cover will expose dangerous voltages. To avoid personal injury, do not
remove the cover. Do not operate the unit without the cover installed.
The appliance must be safely connected to multimedia systems.
Follow instructions described in this manual.
Ventilation
For the correct ventilation and to avoid overheating ensure enough
free space around the appliance. Do not cover the appliance, let the
ventilation holes free and never block or bypass the ventilators (if any).
WARNING
To prevent injury, the apparatus is recommended to securely attach to
The apparatus shall not be exposed to dripping or splashing and that
be placed on the apparatus.
Waste Electrical & Electronic Equipment
WEEE
This marking shown on the product or its literature,
indicates that it should not be disposed with other
household wastes at the end of its working life. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material
resources. Household users should contact either the
retailer where they purchased this product, or their local government
environmentally safe recycling. Business users should contact their
supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for
disposal.
Common Safety Symbols
Symbol Description
Direct current
Alternating current
Double insulation
Caution, possibility of eletric shock
Caution
UMX-TPS-TX100 series – User's Manual 3
Symbol Legend
The following symbols and markings are used in the document:
WARNING! Safety-related information which is highly
recommended to read and keep in every case!
ATTENTION! Useful information to perform a successful procedure;
it is recommended to read.
INFO: A notice which may contain additional information. Procedure
can be successful without reading it.
DEFINITION: The short description of a feature or a function.
TIPS AND TRICKS: Ideas which you may have not known yet but can
be useful.
Navigation Buttons
Go back to the previous page. If you clicked on a link peviously,
you can go back to the source page by the button.
Navigate to the Table Contents.
Step back one page.
Step forward to the next page.
Document Information
This User’s Manual applies to the following versions of the mentioned
Item Version
Lightware Device Controller (LDC) software 1.26.0b6
Lightware Device Updater (LDU) software 1.5.2b3
Controller rmware - UMX-TPS-TX100 series 1.1.1
Controller rmware - WP-UMX-TPS-TX100 series 1.2.0
Controller rmware - FP-UMX-TPS-TX130-MKM 1.3.0
Hardware 1.2
Document revision: 2.1
Release date: 13-11-2018
Editor: Judit Barsony
About Printing
Lightware Visual Engineering supports green technologies and
eco-friend mentality. Thus, this document is made for digital usage
primarily. If you need to print out few pages for any reason, follow the
recommended printing settings:
▪Page size: A4
▪Output size: Fit to page or Match page size
▪Orientation: Landscape
TIPS AND TRICKS: Thanks to the size of the original page, a border
around the content (gray on the second picture below) makes
possible to organize the pages better. After punching the printed
pages, they can be placed easily into a ring folder.
123
UMX-TPS-TX100 series – User's Manual 4
1. INTRODUCTION...................................................................................7
...................................................................................7
......................................................................7
....................................................................7
...............................................................................8
.......................................................................................8
.......................................................................9
...................................................................10
2. INSTALLATION................................................................................... 11
..............................11
................................................... 11
......................................................................... 11
.......................12
.........................12
.......................................................................13
........................................................... 13
.................................................................. 13
.......................................................................14
3. PRODUCT OVERVIEW ......................................................................15
.........................................15
...........................................16
...................................16
.....................................17
.....................................17
.......................................17
.............................................................18
.......................................................... 18
........................................................................ 18
............................................................................... 18
............................................................................. 18
................................................................... 18
............................................................................... 18
........................................................... 18
..................................................... 18
.................................... 19
........................................................................ 19
................................................................................. 19
.................................................................................... 19
............................... 19
...............................................................20
.............................................................................20
...........................................................................21
.........................................................................22
....................................................................... 22
..................................................... 22
...........................................................22
........................................................................23
....................................................................... 23
.............................................................. 23
.....................................................................24
............................................................................. 24
.................................................................................... 25
........................................................... 25
.............................................................................. 26
........................................................26
............ 26
........ 26
... 26
4. OPERATION .......................................................................................27
.......................................................................27
............................................................................ 27
............................................................................ 27
............................................................................... 27
....................................................................................... 27
................................................................................. 28
.......................................................... 28
.........................................................................28
.......................................................................................... 28
..................................................................................... 28
........................................................................................ 28
......................................................................................... 28
.................................................................29
........................................................................ 29
........................................................................ 29
..................................................................................... 29
................................................... 29
......................................................................29
............................................. 29
.................................................. 30
........................................................................ 30
.................................................................................... 30
................................................. 30
..........................................................30
5. SOFTWARE CONTROL - LIGHTWARE DEVICE CONTROLLER ....31
..................................................................31
.........................................................................31
..................32
........................................................................33
..........................................................34
....................................................................... 34
........................................................................ 34
....................................................................... 35
........................................................................ 35
........................................................................... 35
........................................................................... 36
........................................................................37
........................................................................... 37
............................................................................... 38
.................................................................................... 38
...................................................................................39
.............................................................................. 39
................................................................. 40
............................................................................... 40
........................................... 41
............................................................................41
............................................................................................. 41
................................................................................................ 42
........................................................................................... 42
................................................................................................. 43
...........................................................................44
.............................................................................. 45
.............................................................. 45
...................................................... 46
............................................................ 46
.............................................................. 46
............................................................... 46
..........................................................................47
............................................................................................ 47
......................................................................................... 48
.......................................................................................... 48
.................................................................................... 48
.......................................................................................... 49
.......................................49
....................................................................... 49
...................................... 50
.................................. 50
Table of Contents
UMX-TPS-TX100 series – User's Manual 5
Table of Contents
............................................................50
6. LW2 PROGRAMMER'S REFERENCE...............................................51
.........................................................51
.............................................................51
.......................................................................... 51
................................................................... 51
............................................... 52
.............................................................................. 52
........................................................................ 52
.................................................................................. 52
....................................................................... 52
.................................................. 52
.......................................................................... 52
..................................................................... 52
................................................. 52
......................................................................53
........................................................ 53
.................................................................................... 53
............................................................................... 53
..................................................................................... 53
................................................................................. 53
........................................... 54
...................................................................... 54
.................................................... 54
.................................................... 54
................................................ 55
......................................................... 55
.............................................................55
........................................................... 55
.......................................................................... 55
...................................................................... 55
............................................................... 56
.................................................................. 56
....................................................................56
........................................... 56
..............................................57
7. LW3 PROGRAMMERS’ REFERENCE...............................................58
.....................................................................................58
..........................................................................58
........... 58
.................................................................................. 58
............................................................................. 59
.............................................................................. 59
............................................................................... 59
.......................................................................................... 59
......................................................................................... 60
.................................................................................... 60
..................... 60
............................................. 60
......................................................................61
................................................................ 61
....................................................................... 61
................................................................ 61
.......................................................... 61
....................................................................... 61
............................................ 61
........................................................ 62
............. 62
....................................................................................... 62
.......................................................................... 62
...................................................................63
.................................................. 63
............................................ 64
.............................................. 64
.................................................................... 64
............................................. 64
........................................................ 65
.......................................................... 65
....................................................... 65
.......................................................................... 65
................................................................... 65
........................................................................ 66
..................................................................... 66
.................................................................................. 66
............................................................................. 66
.................................................................................. 66
............................................................................... 66
............................................................ 66
...................................................... 67
............................................................... 67
........................................................................ 67
......................................................... 67
............................................. 67
............................................... 68
........................................................ 68
....................................................................... 68
...................................................................69
.................................................. 69
............................................ 69
.............................................. 70
.................................................................... 70
............................................ 70
........................................................ 70
.......................................................... 71
....................................................... 71
....................................................................... 71
................................................................ 71
........................................................................ 71
..................................................................... 71
....................................................................... 72
................................................................... 72
.................................................................................. 72
............................................................................... 72
.............................................. 72
UMX-TPS-TX100 series – User's Manual 6
Table of Contents
.............................................................73
.................................................................... 73
................................................................. 73
...................................................................... 73
..................................................... 73
.................................................................. 73
.................................................. 73
.......................................................... 73
.......................................... 74
.......................................................74
.............................................................................. 74
.......................................................................... 74
................................................................................ 74
.............................................................................. 74
................................................................................... 74
................................................................. 75
............................................................ 75
....................................................75
................................................. 75
.................................... 75
.......................76
..................................................... 76
.............................................. 76
...................................... 77
............................................................. 77
.........................................................78
.................................................... 78
.............................................. 78
.................................................... 78
.....................................................................78
........................................................... 78
......................................... 78
........................ 79
............................................. 79
........................................... 79
.................................................... 79
.......................................... 79
..................................................... 79
.............................................80
8. FIRMWARE UPGRADE......................................................................83
.....................................83
....................................................................83
..................................................................83
................................................................84
............................................................... 84
.................................... 84
.........................................87
...88
9. TROUBLESHOOTING........................................................................89
10. TECHNOLOGIES..............................................................................91
.....................................................................91
............................................................... 91
...................................................... 91
...................................................................92
........................................... 92
................................................. 92
.....................................................93
11. APPENDIX ........................................................................................94
............................................................................94
........................................................96
............................................................96
.........................................................97
..............................................................98
................................................................ 98
......................................................... 99
........................................................... 99
......................................................................100
............................................................100
............................................................100
......................................................................... 100
......................................................................... 100
......................................................................... 101
...................................................................101
...............................................101
...................................................................102
..............................................................103
1. Introduction UMX-TPS-TX100 series – User's Manual 7
1
Introduction
chapter we would like to introduce the device highlighting the most important
features in the below listed sections:
Î
Î
Î
Î
Î
Î
Î
Model Denomination
UMX-TPS-TX140
HDBaseTTM TPS extender Number of outputs
Universal input interfaces -
analog and digital signals
are also accepted
Transmitter
Number of inputs
WP-UMX-TPS-TX130-US White
HDBaseTTM
TPS extender
Number
of
outputs
The device can
be mounted into
B225R outlet box
Universal input interfaces -
analog and digital signals
are also accepted
Transmitter Number
of inputs
Wallplate
The color
of the
enclosure
Description
This transmitter was designed to extend digital and analog video
signals (e.g. VGA, YPrPb, HDMI 1.4 and DP 1.1) and audio signals
(analog stereo audio from local inputs or embedded 7.1 HBR audio).
Video signals with HDCP encryption are also supported. Analog
signals (both audio and video) are converted to digital format and
the audio signals can be de-embedded from the video. Thus, many
Using the factory, custom or transparent EDID emulation the user
Management forces the required resolution from any video source
The unit offers bi-directional and transparent IR, RS-232 and Ethernet
transmission. Furthermore, the IR and RS-232 connection support
command injection, allowing it to send any IR or RS-232 control
command directly from the LAN connection.
Remote powering (Power over Ethernet) is available through a single
CAT cable, but local power supply can also be used. UMX-TPS
transmitter can be mounted on a rack shelf or used standalone
furniture. The transmitters are compatible with both the HDBaseTTM
extenders and matrix switchers.
Compatible Devices
The transmitter is compatible with other Lightware TPS receivers,
matrix TPS and TPS2 boards, 25G TPS2 boards, as well as third-party
HDBaseT extenders, displays, but not compatible with the phased out
TPS-90 extenders.
The transmitter is compatible
with any third-party HDBaseTTM
device.
HDBaseTTM and the HDBaseT Alliance logo are trademarks of the
HDBaseT Alliance.
FP-UMX-TPS-TX130-MKM
HDBaseTTM
TPS extender
Number
of
outputs
The device can
be mounted into
MK Cablelink Plus
Modular series
floorbox
Universal input interfaces -
analog and digital signals
are also accepted
Transmitter Number
of inputs
Floorplate
1. Introduction UMX-TPS-TX100 series – User's Manual 8
WP-UMX-TPS-TX100 series
FP-UMX-TPS-TX100 series
Optional Accessories
The following accessories can be purchased separately:
Safety & warranty info,
Safety and
Warranty
Info
Quick
Start
Guide
Safety and
Warranty
Info
Quick
Start
Guide
48V DC power adaptor
with interchangeable
plugs
box (B225R) for
mounting
Box Contents
UMX-TPS-TX100 series
* Only for UMX-TPS-TX130 and UMX-TPS-TX140 models.
** Only for UMX-TPS-TX140 model.
UMX-TPS-TX100
series transmitter
12V DC adaptor with
interchangeable plugs
Infrared emitter unit
Phoenix®Combicon
3-pole connector
Safety & warranty info,
Phoenix®Combicon
8-pole connector *
Phoenix®Combicon
5-pole connector **
Safety and
Warranty
Info
Quick
Start
Guide
Features
3D and 4K Support
High bandwidth allows extension of resolutions up to 4K
and even 3D sources and displays are supported.
Signal Transmission up to 170 m
Video and audio signal transmission (HDMI, Ethernet,
RS-232, and Infra-Red over a single CAT5e…CAT7e cable.
Analog audio and video signals are converted to digital
before being sent to the output.
Deep Color Support and Conversion
It is possible to transmit the highest quality 36-bit video
streams for perfect color reproduction.
Pixel Accurate Reclocking
Each output has a clean, jitter free signal, eliminating
signal instability and distortion caused by long cables or
on the digital video inputs can be disabled when non-
protected content is extended.
Built-in Event Manager
The Event Manager tool takes care of all the necessary
Hence, in a less complex environment, there is no need
to invest in additional control solutions, which makes the
receiver the best choice for numerous applications.
Autoselect Function for Video Inputs
The Autoselect feature can sense the port status on the
video input ports and select automatically one of them.
Priority number can be set for each input port and the
feature allows to set various modes for the automatic
input selection (First detect, Last detect, Priority mode).
FP-UMX-TPS-TX130
transmitter
Phoenix®Combicon
3-pole connector
series transmitter
Fixing screws for
mounting (4 pcs.
6-32 x 1”, oval head) 2
Phoenix®Combicon
3-pole connector
Fixing screws
for mounting
(4 pcs. 3.9x 22mm,
1
1
For white models
series.
2 For black models of
series.
1. Introduction UMX-TPS-TX100 series – User's Manual 9
Breakaway Audio/Video Switching
audio and video separately by de-embedding and
audio can be de-embedded from the incoming HDMI
stream, then at output a different audio can be embedded
into the video signal from a different source, or audio can
be routed to a separate output port.
Remote Power
The transmitters are PoE-compatible and can be powered
locally by the supplied power adaptor, or remotely via
the TPS connection (through the CATx cable) with a
compatible power source equipment.
TPS Cable Diagnostic Tool
The TPS Cable Diagnostics Tool within the LDC software
will help you identify potential twisted pair cable issues
in your TPS-capable (HDBaseT compliant) system. It
provides a real-time overview of the estimated cable
lengths and the quality of the link.
IR
Infrared (IR) is a wireless technology used for device
communication over short ranges. IR communication
has major limitations because it requires line-of-sight,
has a short transmission range and is unable to penetrate
walls. Infrared is commonly used for remote control
based applications. Third-party control systems may
send IR control commands to endpoints turning them on
and off or switching their inputs. IR capable extenders
can carry the IR signal via CAT cable to greater distances
along with other data.
RS-232 Bi-directional RS-232 Pass-through
AV systems can also contain serial port controllers and
controlled devices. Serial port pass-through supports
any unit that works with standard RS-232.
GPIO Control Port *
7 GPIO pins operating at TTL digital signal levels and can
* Only for UMX-TPS-TX130 and UMX-TPS-TX140 models.
Model Comparison
The available models have different features depending on their design. The following table contains the most important differences between the models:
Video ports Audio ports Interface ports
HDMI
input VGA input DVI-I
input DP input Jack 3.5
input Phoenix Ethernet Infra RS-232 GPIO
UMX-TPS-TX120 - - - -
UMX-TPS-TX130 --
UMX-TPS-TX140
WP-UMX-TPS-TX120-US Black - - - -
WP-UMX-TPS-TX120-US White - - - -
WP-UMX-TPS-TX130-US Black - - -
WP-UMX-TPS-TX130-US White - - -
FP-UMX-TPS-TX130-MKM - - -
1. Introduction UMX-TPS-TX100 series – User's Manual 10
Typical Application
Standalone Application Diagram - UMX-TPS-TX140
Integrated System Diagram - UMX-TPS-TX140
PIN: 2.1mm GPIO
RS-232
TXRX
AUDIO2 IN
DVI-I IN
IR IN IR OUT
LIVE
RS-232
SRVC
LINK
12V 1A DC
Touch panel Button panel
PC
DVI
VGA
analog
audio
IR
Ethernet
switch
UMX-TPS-TX140
Blu-ray player
MAC
RS-232
Laptop
12V DC power
adaptor
12V DC
power
adaptor
IR emitter
WiFi
access
IR
RS-232
HDMI
TPS connection
CATx up to 170m
HDMI-TPS-RX97
IR detector
HD Projector
HDMI
DP
Internet LAN
LAN
LAN
Remote control
Sn:
Madein EU, Hungary
RoHS
Ethernet 10/100
Bidirectional IR
Bidirectional RS-232
HDMI, 3D, 4K supported
HHDDMMII--TTPPSS--RRXX9977
Sn:
TTPPSS LLoonngg DDiissttaannccee RReecceeiivveerr
PIN:2mm
12V1A DC
For best performance use AWG23CAT6 or CAT7 SFTP cable
Device can be remote powered over TPS link with PoE
(IEEE 802.3af)
TPSIN PoE
( )
RS-232
HDMI
HDMI
CATx
(up to 170 m)
CATx
(up to 170 m)
LAN
LAN
HDMI
audio
audio
MX-TPS-IB-S
12V3A
DCIN
8CH TPS INPUT BOARD 12Vpower on TPS connector. Only use with compatible devices!
TPS IN 1 TPSIN 2 TPSIN3 TPSIN 4 TPSIN 5 TPS IN 6 TPSIN 7 TPSIN8
AV Receiver
Speaker
HDMI-TPS-RX97
Local monitor
Laptop
Projector
Ethernet
switch
MX-FR17
8CHINPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-IB-A
IN1 IN2 IN 3 IN4 IN 5 IN6 IN 7 IN8
MX-TPS-OB-S
12V4A
DCIN
8CH TPS OUTPUT BOARD WITH DIGITAL AUDIO 12Vpoweron TPS connector. Only use with compatible devices!
TPSOUT 1 TPSOUT 2 TPSOUT 3 TPS OUT 4 TPSOUT 5 TPSOUT 6 TPS OUT 7 TPSOUT 8
S/PDIF I/O 1 S/PDIFI/O 2 S/PDIF I/O 3 S/PDIFI/O 4 S/PDIFI/O 5 S/PDIF I/O 6 S/PDIFI/O 7 S/PDIF I/O 8
8CHOUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-OB-A
OUT1 OUT2 OUT 3 OUT 4 OUT5 OUT 6 OUT7 OUT8
HDMI
LAN
12V DC
power
adaptor UMX-TPS-TX140
PC or MAC
PIN: 2.1mm GPIO
RS-232
TXRX
AUDIO2 IN
DVI-I IN
IRIN IR OUT
LIVE
RS-232
SRVC
LINK
12V 1A DC
Ethernet
Sn:
Madein EU, Hungary
RoHS
Ethernet 10/100
Bidirectional IR
Bidirectional RS-232
HDMI, 3D, 4K supported
HHDDMMII--TTPPSS--RRXX9977
Sn:
TTPPSS LLoonngg DDiissttaannccee RReecceeiivveerr
PIN:2mm
12V1A DC
Forbest performance use AWG23 CAT6 or CAT7 SFTP cable
Devicecan be remote powered over TPS link with PoE
(IEEE802.3af)
TPSIN PoE
( )
Standalone Application Diagram - WP-UMX-TPS-TX130-US
WP-UMX-TPS-TX130-US
VIDEO
SELECT
ETHERNET
INPUT STATUS
VIDEO AUDIO
O
RESET
IR
VGA
DP
HDMI
Autoselect
AUDIO
SELECT SHOW
ME
2DP IN 3
AUDIO
DP
HDMI
TPSLink
analog
audio
Laptop
Ethernet
switch
MAC
WP-UMX-TPS-
TX130-US Blu-ray
player
12V DC power
adaptor
12V DC
power
adaptor
WiFi
access
RS-232
HDMI
TPS connection
CATx up to 170m
HDMI-TPS-RX97
IR
DP
HD Projector
Internet
LAN
LAN
LAN
HDMI
VGA
Sn:
Made in EU, Hungary
RoHS
Ethernet 10/100
Bidirectional IR
Bidirectional RS-232
HDMI, 3D, 4K supported
HHDDMMII--TTPPSS--RRXX9977
Sn:
TTPPSS LLoonngg DDiissttaannccee RReecceeiivveerr
PIN:2mm
12V 1A DC
For best performance use AWG23CAT6 or CAT7 SFTP cable
Device can be remote powered over TPS link with PoE
(IEEE 802.3af)
TPSIN PoE
( )
2. Installation UMX-TPS-TX100 series – User's Manual 11
2
Installation
The chapter is about the installation of the device and connecting to other
appliances, presenting also the mounting options and further assembly steps
Î
Î
Î
Î
Î
Mounting Options - UMX-TPS-TX100 series
To mount the transmitter Lightware supplies optional accessories for
different usage. There are two kinds of mounting kits with similar
on the bottom side; see the bottom view in the Mechanical Drawings
section. Fasten the device by the screws enclosed to the accessory:
Under-desk double mounting kit
1U high rack shelf
The Under-desk double mounting kit makes easy to mount a single
mounting holes for fastening two half-rack or four quarter-rack sized
units. Pocket-sized devices can also be fastened on the shelf. To order
INFO: The transmitter is half-rack sized.
Under-desk Double Mounting Kit
The UD-kit double makes it easy to mount a single transmitter on any
VIDEO AUDIO
DVI-AVideo
Autoselect
HDCP
Audio2
DVI-D
DP
DVI-D
DP
SHOW
ME
AUDIO
SELECTINPUT STATUS
VIDEO
SELECT
HDMI HDMI
VGA Audio1 RESET
AUDIO1 IN HDMI IN DP INVGAIN
INFO: The chipboard screws are not supplied with the mounting kit.
Allows rack mounting for half-rack, quarter-rack and pocket sized
units.
1U high rack shelf provides mounting holes for fastening two half-rack
or four quarter-rack sized units. Pocket sized devices can also be
fastened on the self.
Standard rack installation
ATTENTION!
ears to the rack rail. Choose properly sized screws for mounting.
Keep minimum two threads left after the nut screw.
VIDEO AUDIO
DVI-AVideo
Autoselect
HDCP
Audio2
DVI-D
DP
DVI-D
DP
SHOW
ME
AUDIO
SELECTINPUT STATUS
VIDEO
SELECT
HDMI HDMI
VGA Audio1 RESET
AUDIO1 IN HDMIIN DP INVGA IN
VIDEO AUDIO
DVI-AVideo
Autoselect
HDCP
Audio2
DVI-D
DP
DVI-D
DP
SHOW
ME
AUDIO
SELECTINPUT STATUS
VIDEO
SELECT
HDMI HDMI
VGA Audio1 RESET
AUDIO1 IN HDMIIN DP INVGA IN
UUMMXX--TTPPSS--TTXX114400
Universal TPS Transmitter
INPUT STATUSLED FUNCTIONS
Blinking: Selected input has no signal
Continuous ON: Signal present on active input
AUDIO SELECT:
VIDEO SELECT:
Made in EU, Hungary
RoHS
Sn:
Rear LED functions Port legend
LIVE Video only
Audio only
Video with embedded audio
RS-232
SRVC
Fast blinking (0.5 sec): Firmware upgrade mode
Continuous ON: Powered but no operation
OFF: No power
OFF: Pass-through mode
Blinking (1 sec): Normal operation
Blinking: Command injection mode
ON: Control mode
Reserved
OFF: No TPS link
TPS link
Blinking: Low power mode
ON: TPS link good
DVI-DHDMI DPVGA
Autoselect DVI-A
HDMI emb. DP emb.Audio1
Audio2 DVI-D emb.
For best performance use AWG23
CAT6 or CAT7SFTP cable
Device can be remote powered over TPS link with PoE
(IEEE 802.3af)
2
UUMMXX--TTPPSS--TTXX114400
Universal TPS Transmitter
INPUT STATUSLED FUNCTIONS
Blinking: Selected input has no signal
Continuous ON: Signal present on active input
AUDIO SELECT:
VIDEO SELECT:
Made in EU, Hungary
RoHS
Sn:
Rear LED functions Port legend
LIVE Video only
Audio only
Video with embedded audio
RS-232
SRVC
Fast blinking (0.5 sec): Firmware upgrade mode
Continuous ON: Powered but no operation
OFF: No power
OFF: Pass-through mode
Blinking (1 sec): Normal operation
Blinking: Command injection mode
ON: Control mode
Reserved
OFF: No TPS link
TPS link
Blinking: Low power mode
ON: TPS link good
DVI-DHDMI DPVGA
Autoselect DVI-A
HDMI emb. DP emb.Audio1
Audio2 DVI-D emb.
For best performance use AWG23
CAT6 or CAT7SFTP cable
Device can be remote powered over TPS link with PoE
(IEEE 802.3af)
2
VIDEO AUDIO
DVI-A Video
Autoselect
HDCP
Audio2
DVI-D
DP
DVI-D
DP
SHOW
ME
AUDIO
SELECTINPUT STATUS
VIDEO
SELECT
HDMI HDMI
VGA Audio1
RESET
AUDIO1 IN HDMI IN DP IN
VGA IN
VIDEO AUDIO
DVI-A Video
Autoselect
HDCP
Audio2
DVI-D
DP
DVI-D
DP
SHOW
ME
AUDIO
SELECTINPUT STATUS
VIDEO
SELECT
HDMI HDMI
VGA Audio1
RESET
AUDIO1 IN HDMI IN DP IN
VGA IN
2. Installation UMX-TPS-TX100 series – User's Manual 12
Mounting Options - FP-UMX-TPS-TX130-MKM
FP-UMX-TPS-TX130-MKM bracket is supplied with the product.
Modular series).
Step 1.
the device into the frame.
Tab
Fixing screw
Handle
F
P-UMX-TPS-TX130-MKM
F
P-UMX-TPS-TX130-MKM
bracket
53.4
77 217
FP-UMX-TPS-TX-130-MKM supplied with bracket
Mounting Options - WP-UMX-TPS-TX100 series
The transmitter can be easily mounted into an industrial standard
for the details.
Step 1. Insert the extender into the B225R outlet box and position it to get the
holes aligned.
Step 2. Fasten the front side of the extender to the B225R outlet box by
B225R outlet box
Step 2. Move the handles towards the frame. Align the tab on the
assembly with the slot in the frame.
Step 3.
frame.
Fixing screw
Front side of the
extender
100.6
109.2
70.6
B225R
outlet box
2. Installation UMX-TPS-TX100 series – User's Manual 13
Connecting Steps
WP-UMX-TPS-TX100 series
VGA laptop HDMI laptop
Power
EthernetPower adaptor
WP-UMX-TPS-TX100 series
transmitter
MacBook
HDMIVGA DPAudio
Relay box
LAN
RS-232
CATx
Compatible
receiver or
input board
WWPP--UUMMXX--TTPPSS--TTXX113300--UUSS
VIDEO
Autoselect
HDMI
INPUT STATUS
SHOW
ME
DP
VGA
AUDIO
TPSLINK
HDMI
DP
AUDIO
AUDIO
SELECT
IR
VIDEO
SELECT
RESET
Ethernet
AUDIO IN HDMI IN
VGA IN DP IN
CATx
Connect the transmitter and a compatible receiver or the matrix input board by a CATx cable
via the TPS connectors.
HDMI
DP
VGA
DisplayPort cables.
Audio
Optionally connect an asymmetric audio device with unbalanced audio signal (e.g. a
VGA laptop) to the 2.5" TRS (jack) audio input port.
LAN
Optionally connect the transmitter to a LAN network in order to control the device.
RS-232
Power
See powering options in the next section.
UMX-TPS-TX100 series
VGA laptop HDMI laptop
Power GPIO IR
EthernetPower adaptor Infrared
UMX-TPS-TX100 series
transmitter
PC MacBook Media player
HDMI DVI
VGA DP
Audio Audio
Relay box
LAN
RS-232
VIDEO AUDIO
DVI-A Video
Autoselect
HDCP
Audio2
DVI-D
DP
DVI-D
DP
SHOW
ME
AUDIO
SELECTINPUT STATUS
VIDEO
SELECT
HDMI HDMI
VGA Audio1 RESET
AUDIO1 IN HDMI IN DP INVGA IN
CATx
Compatible
receiver or
input board
Touch panel
CATx
Connect the the transmitter and a compatible receiver or the matrix input board by a CATx cable via
the TPS connectors.
HDMI
DVI
DP
VGA
cables.
Audio
Optionally connect an asymmetric audio device with unbalanced audio signal (e.g. a VGA laptop)
to the 2.5" TRS (jack) audio input port.
Audio
Optionally connect a symmetric audio device with balanced audio signal (e.g. a media player) to
the 5-pole Phoenix audio input port. See the wiring guide for the connector in the Audio Cable
section.
IR
Optionally for Infrared control:
- Connect the IR emitter to the IR OUT port of the device.
- Connect the IR detector to the IR IN port of the device.
LAN
Optionally connect the transmitter to a LAN network in order to control the device.
RS-232
GPIO
Power
See powering options in the next section.
2. Installation UMX-TPS-TX100 series – User's Manual 14
Powering Options
MX-TPS-IB-S
12V3A
DC IN
8CH TPS INPUT BOARD 12Vpower on TPS connector. Only use with compatible devices!
TPS IN 1 TPSIN 2 TPSIN 3 TPSIN 4 TPS IN 5 TPS IN 6 TPSIN 7 TPSIN 8
8CHINPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-IB-A
IN1 IN 2 IN3 IN4 IN 5 IN 6 IN 7
IN8
MX-TPS2-OB-S
48V5A
DC IN
8CH TPS OUTPUT BOARD WITH DIGITAL AUDIO 12Vpower on TPS connector. Only use with compatible devices!
TPSOUT 1 TPS OUT 2 TPS OUT 3 TPSOUT 4 TPS OUT 5 TPS OUT 6 TPS OUT 7 TPS OUT 8
S/PDIF I/O 1 S/PDIFI/O2 S/PDIFI/O 3 S/PDIFI/O4 S/PDIFI/O5 S/PDIFI/O 6 S/PDIFI/O7 S/PDIFI/O 8
8CHOUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-OB-A
OUT1 OUT2 OUT3 OUT 4
OUT5
MX-FR17
CATx
(TPS)
External
power supply
Power send
WP-UMX-TPS-TX130-US
VIDEO
SELECT
ETHERNET
INPUTSTATUS
VIDEO AUDIO
O
RESET
IR
VGA
DP
HDMI
Autoselect
AUDIO
SELECT SHOW
ME
2DPIN 3
AUDIO
DP
HDMI
TPSLink
TPS-PI-1P1
48DC IN
Typical:0.7A
Max:1.5A
- +
Max:2.5A
PIN:2mm
CATx
(TPS)
Power
send
48V DC
Power
adaptor
WP-UMX-TPS-TX130-US
VIDEO
SELECT
ETHERNET
INPUTSTATUS
VIDEO AUDIO
O
RESET
IR
VGA
DP
HDMI
Autoselect
AUDIO
SELECT SHOW
ME
2DPIN 3
AUDIO
DP
HDMI
TPSLink
48V DC
Power
adaptor
WP-UMX-TPS-TX130-US
VIDEO
SELECT
ETHERNET
INPUTSTATUS
VIDEO AUDIO
O
RESET
IR
VGA
DP
HDMI
Autoselect
AUDIO
SELECT SHOW
ME
2DPIN 3
AUDIO
DP
HDMI
TPSLink
ABC
MX-TPS-IB-S
12V3A
DC IN
8CH TPS INPUT BOARD 12Vpower on TPS connector. Only use with compatible devices!
TPS IN 1 TPSIN 2 TPSIN 3 TPSIN 4 TPS IN 5 TPSIN 6 TPSIN 7 TPSIN 8
8CHINPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-IB-A
IN1 IN 2 IN 3 IN 4 IN 5 IN 6 IN 7
IN8
MX-TPS2-OB-S
48V5A
DC IN
8CH TPS OUTPUT BOARD WITH DIGITAL AUDIO 12Vpower on TPS connector. Only use with compatible devices!
TPSOUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4 TPS OUT 5 TPS OUT 6 TPSOUT 7 TPS OUT 8
S/PDIF I/O 1 S/PDIFI/O2 S/PDIFI/O 3 S/PDIFI/O4 S/PDIFI/O5 S/PDIF I/O 6 S/PDIF I/O 7 S/PDIFI/O 8
8CHOUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-OB-A
OUT1 OUT2 OUT3 OUT 4
OUT5
TPS-PI-1P1
48DC IN
Typical:0.7A
Max:1.5A
- +
Max:2.5A
PIN:2mm
CATx
(TPS)
Power
send
External
power supply
PIN: 2.1mm GPIO
RS-232
TXRX
AUDIO2 IN
DVI-I IN
IRIN IR OUT
LIVE
RS-232
SRVC
LINK
12V 1A DC
12V DC power
adaptor
PIN: 2.1mm GPIO
RS-232
TXRX
AUDIO2 IN
DVI-I IN
IRIN IR OUT
LIVE
RS-232
SRVC
LINK
12V 1A DC
PIN: 2.1mm GPIO
RS-232
TXRX
AUDIO2 IN
DVI-I IN
IRIN IR OUT
LIVE
RS-232
SRVC
LINK
12V 1A DC
CATx
(TPS)
Power
send
MX-FR17
A
Using local PSU
power socket.
B
Using PoE with connecting a transmitter: connect the TPS OUT (PoE) port of the transmitter to the
TPS+PoE port of the TPS-PI-1P1 power injector by a CATx cable, and connect the TPS input port of
the compatible receiver to the TPS port of the TPS-PI-1P1 by a CATx cable.
C
Using PoE with connecting a matrix or an input board: connect the TPS OUT (PoE) port of the
transmitter to the PoE-compatible TPS input port of the matrix or input board by a CATx cable.
ATTENTION! In case of connecting the transmitter to an input board of the matrix always connect an
external PSU to the board. For the detailed information please read the user's manual of the matrix.
ATTENTION! The Ethernet port does not support PoE. Only the TPS port support PoE function.
3. Product Overview UMX-TPS-TX100 series – User's Manual 15
3
Product Overview
output ports and connectors:
Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Front View - UMX-TPS-TX100 series
UMX-TPS-TX120
UMX-TPS-TX130
UMX-TPS-TX140
1VGA input D-SUB connector for analog video signal.
2Audio1 input 3.5 mm Jack connector for asymmetric analog audio input signal.
3 HDMI connector for DVI video or HDMI video and audio.
4DisplayPort input
5Input Status LEDs LEDs give feedback about the current status of the unit and input signals.
See the details in the Front Panel LEDs section.
6Video Select button Button for switching between video sources. See the details in the Video
Select Button section.
7Reset button Pushing the button reboots the unit.
8Audio Select button Button for switching between audio sources. See the details in the Audio
Select Button section.
9Show Me button
(bootload) mode, DHCP settings, restore factory default settings,
condition launching in Event Manager).
1 2 3
5
76 8 9
1 2 3
5
76 8 9
1 2 3
5
76 8 94
3. Product Overview UMX-TPS-TX100 series – User's Manual 16
Rear View - UMX-TPS-TX100 series
UMX-TPS-TX120
UMX-TPS-TX130
UMX-TPS-TX140
112V DC input 12V DC input for local powering. For more details see the Locking 12V DC
Connection section or see all the available Powering Options.
2RS-232
connector
3-pole Phoenix connector for controlling the device with LDC or third-party control
systems, or third-party device control. Pin assignment can be found in the RS-232
Connector section.
3GPIO
assignment can be found in the section.
4Ethernet
Controller (LDC), or upgrading it using Lightware Device Updater (LDU). Any third-
party control system can use this port to control the device.
5TPS OUT
Locking RJ45 connector for HDBaseTTM signal transmission. Maximum CATx
cable distances can be found in the Maximum Extension Distances section.
6Status LEDs The LEDs give feedback about the actual state of the device. See the details in the
Rear Panel LEDs section.
7IR IN and
OUT
receiver (IR IN) and transmitter (IR OUT) connection. Pin assignments can be
found in the IR Connector section.
8Audio2 input 5-pole Phoenix connector for balanced analog audio input. Pin assignment can
be found in the Analog Stereo Audio (Phoenix) section.
9DVI-I input
the DVI-I Connector section.
2
7
4 5 6
1
2 3
7
9
45 6
1
2 3
7
8 9
45 6
1
Front View - WP-UMX-TPS-TX100 series
WP-UMX-TPS-TX120-US WP-UMX-TPS-TX130-US
1Input Status LEDs LEDs give feedback about the current status of the unit and input signals.
See the details in the Front Panel LEDs section.
2Audio Select button Button for switching between audio sources. See the details in the Audio
Select Button section.
3Video Select button Button for switching between video sources. See the details in the Video
Select Button section.
4Ethernet
Device Controller (LDC), or upgrading it using Lightware Device Updater
(LDU). Any third-party control system can use this port to control the
device.
5VGA input D-SUB connector for analog video signal.
6Audio input 3.5 mm Jack connector for asymmetric analog audio input signal.
7Show Me button
(bootload) mode, DHCP settings, restore factory default settings,
condition launching in Event Manager).
8Reset button Pushing the button reboots the unit.
9IR detector IR Detector can sense IR light which can be forwarded to the receiver
side or use for controlling functions.
q HDMI connector for DVI video or HDMI video and audio.
wDisplayPort input
1
3
4
5
2 7
8
9
6q
1
3
4
5
2 7
8
9
6w
q
3. Product Overview UMX-TPS-TX100 series – User's Manual 17
Rear View - WP-UMX-TPS-TX100 series
WP-UMX-TPS-TX120-US and WP-UMX-TPS-TX130-US
1RS-232
connector
3-pole Phoenix connector for controlling
the device with LDC or third-party control
systems, or third-party device control. Pin
assignment can be found in the RS-232
Connector section.
2TPS output
Locking RJ45 connector for HDBaseTTM
signal transmission. Maximum CATx cable
distances can be found in the Maximum
Extension Distances section.
348V DC input Power the device remotely by a PoE-
compatible power injector (TPS-PI-1P1).
If the device has to be powered by a local
adaptor (PSU-48VP1), connect the output
to the 2-pole Phoenix connector on the rear
of the wall plate. See more details about
powering options in the 48V DC Connection
section or see all the available Powering
Options.
2
3
1
Front View - FP-UMX-TPS-TX130-MKM
1Input Status
LEDs
LEDs give feedback about the current status of
the unit and input signals. See the details in the
Front Panel LEDs section.
2Audio Select
button
Button for switching between audio sources. See
the details in the Audio Select Button section.
3Video Select
button
Button for switching between video sources. See
the details in the Video Select Button section.
4Ethernet
device using Lightware Device Controller (LDC),
or upgrading it using Lightware Device Updater
(LDU). Any third-party control system can use
this port to control the device.
5VGA input D-SUB connector for analog video signal.
6Audio input 3.5 mm Jack connector for asymmetric analog
audio input signal.
7Show Me
button
Special functions can be reached using this
DHCP settings, restore factory default settings,
condition launching in Event Manager).
8Reset button Pushing the button reboots the unit.
3
1
3
4
q
2
8
9
6w
7
5
9IR detector IR Detector can sense IR light which can
be forwarded to the receiver side or use for
controlling functions.
q HDMI connector for DVI video or HDMI video
and audio.
wDisplayPort
input
video signal.
Rear View - FP-UMX-TPS-TX130-MKM
1TPS output
Locking RJ45 connector for HDBaseTTM signal
transmission. Maximum CATx cable distances
can be found in the Maximum Extension
Distances section.
2RS-232
connector
3-pole Phoenix connector for controlling the
device with LDC or third-party control systems,
or third-party device control. Pin assignment
can be found in the RS-232 Connector section.
348V DC
input
Power the device remotely by a PoE-compatible
power injector (TPS-PI-1P1). If the device has
to be powered by a local adaptor (PSU-48VP1),
connect the output to the 2-pole Phoenix
more details about powering options in the
48V DC Connection section or see all the
available Powering Options.
1 2 3
3. Product Overview UMX-TPS-TX100 series – User's Manual 18
Electrical Connections
Locking 12V DC Connection
Locking DC connector
UMX-TPS-TX100 series transmitters are built with locking 12V DC
connector. Do not forget to turn the plug clockwise direction before
disconnecting the power adaptor.
WARNING! Always use the supplied 12V power adaptor. Warranty
void if damage occurs due to use of a different power source.
48V DC Connection
Phoenix connector for 48V DC 1A power connection.
Pin nr. Signal
1 +
2 -
2-pole Phoenix connector and plug pin assignments
VGA Connector
The transmitter provides a standard 15-pole
D-SUB female connector for connecting VGA
devices. Always use high-quality VGA cable for
connecting sources and displays; using a VGA cable where all the pins
are wired (including the DDC channel's wires) is highly recommended.
The extender provides standard 19 pole HDMI connector
for input. Always use high quality HDMI cable for
connecting sources and displays.
DisplayPort Connector
provide standard 20-pole DisplayPort connector for input.
Always use high quality DP cable for connecting DisplayPort devices.
12V
1A
DC
12V
1A
DC
PIN: 2.1mm
PIN: 2.1mm
21
DVI-I Connector
UMX-TPS-TX130 and UMX-TPS-TX140 transmitters provide a standard
29-pole DVI-I connector for input where digital and analog pins are
connected internally. Hence users can use the connector receiving
DVI-A (analog video) and DVI-D signals (digital video and digital audio)
as well.
ATTENTION! Only one (DVI-A or DVI-D) mode is available at a time.
You can use the Video Select button to choose the input source.
Always use high quality DVI cable for connecting DVI devices.
The following drawing and table show the pinout of DVI-I connector
and the position of analog and digital signal pins.
Pin Signal Pin Signal
1TMDS Data2- 16 Hot Plug Detect
2TMDS Data2+ 17 TMDS Data0-
3TMDS Data2 Shield 18 TMDS Data0+
4not connected 19 TMDS Data0 Shield
5not connected 20 not connected
6DDC Clock 21 not connected
7DDC Data 22 TMDS Clock Shield
8Analog Vertical Sync 23 TMDS Clock+
9TMDS Data1- 24 TMDS Clock-
10 TMDS Data1+ C1 Analog Red
11 TMDS Data1 Shield C2 Analog Green
12 not connected C3 Analog Blue
13 not connected C4 Analog Horizontal Sync
14 +5V Power C5 GND
15 GND (for +5V)
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
C1 C2
C4C3
C5
17 18 19 20 21 22 23 24
The connector is used for receiving unbalanced analog audio
phone jack, phone plug and mini-jack plug.
Pin nr. Signal
1 Left
2 Right
3 Ground
Jack audio plug pin assignments
Audio
Interface section.
5-pole Phoenix connector is used for balanced analog
audio input in the UMX-TPS-TX140 transmitter.
Unbalanced audio signals can be connected as well. See more details
about the balanced and unbalanced input port wiring in the Audio
section.
Pin nr. Signal
1 Left+
2 Left-
3 Ground
4 Right-
5 Right+
Analog audio connector and plug pin assignments
Compatible Plug Type
Phoenix®
Audio Interface section.
1 2 3
1 2 3 4 5
3. Product Overview UMX-TPS-TX100 series – User's Manual 19
The extender provides standard RJ45 connectors for TPS IN and
LAN ports. Always use high quality Ethernet cable for connecting
transmitters and receivers. Maximum CATx cable distances can be
found in the Maximum Extension Distances section.
18 81 18
LAN connector TPS connector of
UMX-TPS-TX100
series transmitters
TPS connector of
WP-UMX-TPS-TX100
series transmitters
Wiring of TPS and LAN Cables
Lightware recommends the termination of LAN cables on the basis of
Pin assignments of RJ45 connector types
TPS Interface
section.
1
8
Top
8
1
Bottom Side
Pin Color and name Color and name
1
2green solid orange solid
3
4blue solid blue solid
5
6orange solid green solid
7
8brown solid brown solid
RS-232 Connector
The extender contains a 3-pole Phoenix connector which is
used for RS-232 serial connection.
Pin nr. Signal
1 Ground
2 TX data
3 RX data
RS-232 connector pin assignments
Compatible Plug Type
Phoenix®
Serial Interface section.
IR Connector
IR detector and IR emitter can be connected to the
UMX-TPS-TX100 series extenders with TRS (Tip, Ring, and
Sleeve) connectors. They are also known as (3,5 mm or approx.
assignments are the following for the detector and the emitter:
1 2 3
1 2-3
1 Tip Signal (active low) 1 Tip +5V
2 Ring GND 2 Ring Signal (active low)
3 Sleeve +5V 3 Sleeve
INFO: Ring pole of the emitter is optional. If your IR emitter has
three-pole TRS plug, then the Ring and the Sleeve are the same
signal (Output - ).
IR Interface section.
IR Detector
on front panel of the wallplate. The sensor is used for receiving IR
signals from remote control or other IR emitter devices.
IR Interface section.
1 2 3
UMX-TPS-TX130 and UMX-TPS-TX140
transmitters contain a 8-pole Phoenix connector
with seven GPIO pins, which operates at TTL
digital signal levels and can be set to high or low
level (Push-Pull). The direction of the pins can be
input or output (adjustable). Voltage ranges for
GPIO inputs are the following:
Input
voltage [V]
Output
voltage
[V]
Max. current
[mA]
Logical low level 0 - 0.8 0 - 0.5V 30
Logical high level 2 - 5 4.5 - 5V 18
INFO: The maximum total current for the seven GPIO pins is 180 mA.
Pin nr. Level and
direction
1
2
3
4
5
6
7
Ground
GPIO connector and plug pin assignments
Compatible plug type
Phoenix®
GPIO Interface section.
1 2 3 4 5 6 7 8
3. Product Overview UMX-TPS-TX100 series – User's Manual 20
TPS Extender Concept
digital conversion and audio embedding functions. The devices receive analog (VGA, DVI-A) and digital (DP,
Ethernet, RS-232, and Infrared signals. Analog audio signals can be received via the 3.5” TRS (jack) and the
5-pole Phoenix connectors.
The device can be controlled via Ethernet, RS-232 or Infrared and is able to control third-party devices via the
RS-232, Ethernet, Infrared interfaces.
The summary of the interfaces of UMX-TPS-TX100 series transmitters
The summary of the interfaces of WP- and FP -UMX-TPS-TX100 series transmitters
1Only for UMX-TPS-TX140 model.
2Only for UMX-TPS-TX130 and UMX-TPS-TX140 models.
TPS
INPUT OUTPUT
VGA
HDMI
DP
1
DVI-D
2
DVI-A
2
Analog audio
HDMI / DVI
Ethernet
RS-232
Infrared
+ Ethernet
+ RS-232
+ Infrared
+ GPIO
2
VIDEO AUDIO
DVI-A Video
Autoselect
HDCP
Audio2
DVI-D
DP
DVI-D
DP
SHOW
ME
AUDIO
SELECTINPUT STATUS
VIDEO
SELECT
HDMI HDMI
VGA Audio1 RESET
AUDIO1 IN HDMI IN DP INVGA IN
TPS
INPUT OUTPUT
VGA
HDMI
DP
3
Analog audio
HDMI / DVI
Ethernet
RS-232
Infrared
+ Ethernet
+ RS-232
+ Infrared
WWPP--UUMMXX--TTPPSS--TTXX113300--UUSS
VIDEO
Autoselect
HDMI
INPUT STATUS
SHOW
ME
DP
VGA
AUDIO
TPSLINK
HDMI
DP
AUDIO
AUDIO
SELECT
IR
VIDEO
SELECT
RESET
Ethernet
AUDIO IN HDMI IN
VGA IN DP IN
33
VIDEO
Autoselect
HDMI
INPUT STATUS
SHOW
ME
DP
VGA
AUDIO
TPS LINK
HDMI
DP
AUDIO
AUDIO
SELECT
IR
VIDEO
SELECT
RESET
Ethernet
FP-UMX-TPS-TX130-MKM
AUDIO IN HDMI IN
VGA IN DP IN
2 3
VIDEO
Autoselect
HDMI
INPUT STATUS
SHOW
ME
DP
VGA
AUDIO
TPS LINK
HDMI
DP
AUDIO
AUDIO
SELECT
IR
VIDEO
SELECT
RESET
Ethernet
FP-UMX-TPS-TX130-MKM
AUDIO IN HDMI IN
VGA IN DP IN
2
VIDEO
Autoselect
HDMI
INPUT STATUS
SHOW
ME
DP
VGA
AUDIO
TPS LINK
HDMI
DP
AUDIO
AUDIO
SELECT
IR
VIDEO
SELECT
RESET
Ethernet
FP-UMX-TPS-TX130-MKM
AUDIO IN HDMI IN
VGA IN DP IN
2
or
only difference in the size of the enclosure.
TPS Interface
The device is built with TPS (Twisted Pair Single) interface which are using HDBaseTTM technology. It means
the unit transmits video, audio, Ethernet, RS-232, and Infrared signals via a single CATx cable.
TPS Interface Working Modes
The TPS working mode between the transmitter and the receiver is determined by the mode set in them.
▪Auto: The TPS mode is determined automatically.
▪HDBaseT: Ideal for high resolution signals up to 4K.
▪Long reach: Ideal for big distances up to 1080p@60Hz with extended cable lengths.
▪LPPF1*: Only RS-232 communication is transmitted (@ 9600 baud).
▪LPPF2*: Only RS-232 (@ 9600 baud) and Ethernet communication are transmitted.
* LPPF: Low Power Partial Functionality.
Selected mode on RX side
LPPF1 LPPF2 Long reach Auto
Selected mode
on TX side
LPPF1 LPPF1 LPPF1 LPPF1 LPPF1 LPPF1
LPPF2 LPPF1 LPPF2 LPPF2 LPPF2 LPPF2
LPPF1 LPPF2 HDBaseT Long reach HDBaseT
Long reach LPPF1 LPPF2 Long reach Long reach Long reach
Auto LPPF1 LPPF2 HDBaseT Long reach HDBaseT **
automatically. Long reach mode is not available when both sides are set to Auto mode.
are set to Auto mode, the source side is the initiator. It will negotiate each state transition with its sink side
partner.
in automatic mode. In this case, the mode transition negotiation is initiated by the host-managed device and
the auto-mode device follows through. The allowed cable lengths and resolutions are listed in the Maximum
Extension Distances section.
Other manuals for UMX-TPS-TX100 Series
1
This manual suits for next models
10
Table of contents
Other Lightware Extender manuals
Lightware
Lightware MODEX-OPTS-TX User manual
Lightware
Lightware HDMI20-OPTC series User manual
Lightware
Lightware WP-UMX-TPS-TX120-US Black User manual
Lightware
Lightware DP-OPT-TX150 User manual
Lightware
Lightware Modex-Tx User manual
Lightware
Lightware HDMI-TPS-TX97 User manual
Lightware
Lightware DVI-OPT-RX220-Pro User manual
Lightware
Lightware MODEX-F15-OPTS-TX User manual
Lightware
Lightware HDBaseT HDMI-TPS-RX110AY User manual
Lightware
Lightware HDMI-TPS-TX95 User manual
Lightware
Lightware VINX-110-HDMI-DEC User manual
Lightware
Lightware HDMI-TPS-RX220AK User manual
Lightware
Lightware HDMI-TPS-TX226 User manual
Lightware
Lightware UBEX-PRO20-HDMI-F100 User manual
Lightware
Lightware HDMI-TPS-TX210 User manual
Lightware
Lightware HDBaseT HDMI-TPS-RX110AY User manual
Lightware
Lightware HDMI20-OPTC-TX220-Pro User manual
Lightware
Lightware UMX-TP-TX100R User manual
Lightware
Lightware DVI-HDCP-TPS-TX95 User manual
Lightware
Lightware DP-OPT-TX100 User manual
Popular Extender manuals by other brands
Vanco
Vanco PulseAudio PAEXARC1 manual
Lowara
Lowara GM Series Installation and operating instructions
Cooper Wheelock
Cooper Wheelock Series SPB Installation, testing, operation and maintenance manual
TP-Link
TP-Link TL-WPA8730 quick start guide
NetComm
NetComm NP560 Specifications
Texas Instruments
Texas Instruments DAC121S101EVM user guide
