LightwaveRF JSJS LW826 User manual

On/O/Stop Switch
Operation Manual
Model No: JSJS LW826
OVERVIEW:
connect
LightwaveRF
IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE AND FOR GUIDANCE ON
THE ASSOCIATION OF REMOTE HANDSETS. FOR
HELP AND SETUP GUIDANCE PLEASE VISIT
www.lightwaverf.com
It is important to install this product in accordance
with the tting instructions below. Failure to do so
may render your guarantee void.
OnOStop

SETUP:
The functions illustrated here relate to the operation
of the LightwaveRF Inline Relay. For information
regarding how to pair the On/O/Stop Switch to the
relay, please refer to the setup instructions for that
individual device.
IMPORTANT: The On/O/Stop Switch is only
designed to work with the Inline Relay.
NOTE: If the RF range between the transmitter and
receiver is too great to achieve reliable operation, the
LightwaveRF Connect SIGNAL BOOSTER may be used
in conjunction with this product to increase the
signal strength over greater distances.
OPERATION :
‘ON’ Button - Press once to switch on paired relays.
‘OFF’ Button - Press once to switch opaired relays
‘STOP’ Button - Press once to set paired relays to the
‘stop’ position.
The On/O/Stop Switch is designed to operate the
LightwaveRF Inline Relay. The‘Stop’ function makes it
particularly useful in the operation of curtains and
automatic doors.

Changing the Remote Battery
1. Locate one of the two small slots cut into the
bottom edge of the ‘stop’ and ‘o’ keys on the
On/O/Stop Switch.
2. Using a small screwdriver, gently insert into the slot
and prise oone of the keys.
3. The battery holder is located under the keys.
4. Carefully Replace the CR2032 Coin Cell battery
5. Gently replace the keys and press down until a
‘click’sound is heard.
NOTE:
t$POOFDUDPSSFDUMZBOETFDVSFMZ
t%POPUSFDIBSHF
t,FFQBXBZGSPNDIJMESFO
t%POPUTXBMMPX*GTXBMMPXFETFFLNFEJDBMBEWJDF
immediately)
t1MFBTFEJTQPTFPGVTFECBUUFSJFTSFTQPOTJCMZ

Birmingham Science Park Aston
Faraday Wharf
Holt Street
Birmingham
B7 4BB
Tel: [phone]
Email: [e-mail]
SPECIFICATION
RF frequency: 433.92 MHz
Battery: CR 2032 Battery

*www.mr-resistor.co.uk/item.aspx?i=10031
LightwaveRF dimmer switches use trailing edge technology.
Lighting Compatibility Information
If you are going to use LightwaveRF equipment in your house, please read the
information below to ensure you will get the most out of your hardware.
Loading
Our one and two gang dimmers can handle a maximum of 250W of load on each gang of
the switch. The three and four gang switches have a maximum load of 210W on each gang.
If you exceed this load, the switches may overheat and cease to work correctly.
Each gang requires a minimum load to function. This is generally 40w but can be lower with
some lamps. This is generally the case with LEDs where a load of 14W can be enough to
have the switch operating.
Bulbs
LightwaveRF switches can be used with standard incandescent bulbs, halogen bulbs
(including low energy halogens) and dimmable LED bulbs (see below).
Fluorescent tube lighting, including CFL bulbs cannot be used with LightwaveRF equipment.
This includes the LightwaveRF CFR bulb.
LEDs
As there is no standard set for LEDs at present, we cannot state that every dimmable LED
will work with LightwaveRF equipment. Even if exceeding the minimum load, certain LEDs
will not function on their own. In these situations wiring a dummy load* in parallel across
the circuit will correct the issue.
The following LEDs have been tested and do work when at least 2 lamps are in a circuit:
•AuraLED AL-GU10 PRO 5W
•AuraLED AU-GU10 5x1W
•Auralux AU-5W LED Globe 5x1W
•IstoriaLED G9 DL Flood
•IstoriaLED G9 WW Flood
•TCP Dimmable Energy Saver LED 5W
•Truelux 230-5W-DIM
•Toshiba LDRC0627MU1EUD 6.5W 270lm LED
Please check www.lightwaverf.com for up-to-date information on compatibility.