Lilin PIH-931D User manual

Keyboard Controller
PIH-931D/932T
INSTRUCTION MANUAL
MERIT LI-LIN ENT. CO., LTD
http://www.meritlilin.com 66-931CSE

All the safety and operating instructions should be read before the unit is operated.
The safety and operating instructions should be retained for future reference.
All warnings on the unit and in the operating instructions should be adhered to.
All operating and user instructions should be followed.
Only a qualified electrician should make electrical connections.
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
All cable runs must be within permissible distance.
This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight
of the unit.
IMPORTANT SAFEGUARDS
SAFETY PRECAUTIONS
1. Read Instructions
2. Retain Instructions
3. Head Warnings
4. Follow Instructions
5. Electrical Connections
6. Attachments
7. Cable Runs
8. Mounting
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT OPEN COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
to constitute a risk of electric shock to persons.
the literature accompanying the unit.
Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears
to have been damaged in shipment, replace it properly in its carton and notify the shipper.
Be sure to save:
1. The shipping carton and packaging material. They are the safest material in which to make future shipments
of the equipment.
2. This Installation and Operating Instruction.
If the unit ever needs repair service, the customer should contact our dealer or branch for authorization to
return and shipping instructions.
UNPACKING
SERVICE

PREFACE
1. Introduction
2. Specifications
3. Keyboard Layout
4. Keypad Panel
5. Joystick Operation (Pan/Tilt/Zoom Control)
6. Keyboard System Setting
7. Fast Dome Operation
8. Matrix and Receiver Operation
9. DVR Operation
10. Wiring Diagrams
11. Product Components
12. System Overview and Wiring
........................................................................................................
.....................................................................................................
..................................................................................................
......................................................................................................
...............................................................
.......................................................................................
.............................................................................................
................................................................................
....................................................................................................
................................................................................................
...........................................................................................
.................................................................................
1
2
2
3
4
6
6
9
11
13
16
16
17
Thank you for choosing PIH-931D/932T keyboard controller. For trouble free installation and optimum
performance please read this manual thoroughly before attempting installation or operation.
CONTENTS

INTRODUCTION
The PIH-931D/932T is a keyboard controller for a range of matrix switchers, dome cameras, DVR and
telemetry receivers. It allows operation all the functions of equipment and provides a simple operator
interface.
When matrix is present in the system, up to 8 keyboards can be used. However, one of the keyboards
must always be configured as the Master, having greater access to settings than the slaves.
Data is transmitted via screened, twisted pair cables, usually in serial configuration. (RS-485)
SPECIFICATIONS
Model No.
Joystick
Movement Speed Control
Data Communication
Connector
Control Mode
LCD Display
Keyboard Keypad
Input Voltage
Power Consumption
Operating Temperature
Dimension
Weight
PIH-931D
1350 g
RS-485 Standard
(Format N, 8, 1, Baud rate 9600bps)
RJ-45 / 8Pin
PTZ MATRIX DVR
20 Charactersx4Lines
DC 12V 10% / 250mA
3W
-5 ~ +60 (23 ~ 140 )
340(W) x 194(D) x 103(H) mm
Total 54 keys 0~9 Numeric Keys, CAM, MON,
MATRIX, DVR, PRESET, CLR, ENT, SET, ESC,
ALARM RESET, KEYLOCK, SEQ, AUTO PAN and
SHIFT Keys, Lens Control Keys, DVR control Keys,
Receiver Control Keys, Function Keys
3Axis (Pan/Tilt/Zoom)
Pan 8 Steps
Tilt 8 Steps
Zoom 16 Steps
PIH-932T
1300 g
2Axis (Pan/Tilt)
Pan 8 Steps
Tilt 8 Steps
2

DVR ALARM
RESET
SEQ
MATRIX
123
456
789
0
ESC
MON PRESET
FOCUS
FAR
FOCUS
NEAR
F1 F2 F3
SET
F4
POWER
ALARM
R/T
AUTO
PAN
SHIFT
AUTO
FOCUS
AUTO
IRIS
06/02/15 12 00 00
PTZ MODE ID=000
SEARCH
CTRL2
180
CTRL1
C.SET
SPRAY
ICR
LIGHT
C.ESC
CAM
WIPER
LENS
KEYBOARD LAYOUT
LCD Display
Display the Keyboard system setup menu and operation information.
Joystick
3 Axis(Pan/Tilt/Zoom) / 2 Axis(Pan/Tilt)
Keypad Panel
There are 54 Keys which can control PTZ, MATRIX, DVR and Telemetry Receivers.
Power Indicator
Alarm Indicator
R/T Indicator
Data communicate indication.
Auto pan Indicator
SHIFT Indicator
Shift key status indication.
Auto focus Indicator
Auto iris Indicator
RJ-45 Connector
3

123
456
789
0
FOCUS
FAR
ALARM
RESET
F1 F2 F3 F4
ESC
SET
DVR MATRIX
MON PRESET
SEARCH
CTRL2
180
SEQ
FOCUS
NEAR
AUTO
PAN
SHIFT
AUTO
FOCUS
AUTO
IRIS
CTRL1
C.SET
SPRAY
ICR
LIGHT
C.ESC
CAM
WIPER
LENS
KEYPAD PANEL
SET key
Enter Setup Menu Mode.
ESC key
Use to exit from any function or programming.
ALARM RESET key
Reset alarms and video loss alarms.
(Keyboard Lock) key
Press key for 2 second to enter locking mode. Press
key again for 2 second to unlock the keypad.
Press key in PTZ mode, the keyboard will leave the control over cameras.
CAM key
Select a particular camera.
Or press SHIFT + CAM button to switch to PTZ(Fast Dome) control mode.
DVR key
Select a particular DVR.
Or press SHIFT + DVR button to switch to DVR control mode.
MATRIX key
Press SHIFT + MATRIX button to switch to Matrix control mode.
MON key
Select a particular monitor.
PRESET key
For recalling and storing preset positions.
FUNCTION keys
There are 4 function keys (F1, F2, F3 and F4) to execute different functions under different
operation modes.
Numeric keys
0~9 for entering camera, monitor, DVR number etc.
2009/01/01 12 00 00
KEYPAD LOCK
2009/01/01 12 00 00
PTZMODEID=XX
2009/01/01 12 00 00
PTZ MODE ID = 00
4

CLR key
Clear to setting data.
SPRAY / ICR key
The command key of spray to housing.
Manual IR Cut Filter Swap when keyboard connects to Fast Dome Camera).
Fast Dome Camera).
CTRL 1 / C.SET key
A spare control key when keyboard connects to PIH-820(Receiver) or Matrix.
OSD Setup Menu recall key when keyboard connects to Fast Dome Camera).
CTRL 2 / 180 key
A spare control key when keyboard connects to PIH-820(Receiver) or Matrix.
180 Horizontal Instant Flip key when keyboard connects to Fast Dome Camera.
SEARCH key
Perform date and time search based on recorded video data when keyboard connects to DVR.
SHIFT key
Press SHIFT key to switch and match other buttons to execute different functions.
AUTO PAN key
Put a Pan/Tilt head into auto pan mode or a Fast Dome Camera into auto tour mode.
SEQ key
Start an automatic switching sequence on a particular monitor.(Matrix)
(ZOOM IN / ZOOM OUT) keys
Adjust the zoom of the lens manually.
*
*
*
FOCUS FAR / FOCUS NEAR keys
Adjust the focus of the lens manually.
AUTO FOCUS key
Set the focus of the lens to automatic mode when connects to Fast Dome Camera.
(IRIS OPEN / IRIS CLOSE) keys
Open or close the iris of the lens manually.
AUTO IRIS key
Set the iris of the lens to automatic mode.
DVR Control keys
DVR operational keys including 4, 8, 9, 16 split display, record, playback, pause, stop, fast
forward and fast rewind.
ENT key
Used to enter or confirm data and programming.
WIPER / LENS key
The command key of housing wiper when keyboard connects to PIH-820 (Receiver).
Manual speed switch of Zoom, Focus and Iris when keyboard connects to Fast Dome Camera).
LIGHT / C.ESC key
Auxiliary lighting switch when keyboard connects to PIH-820 (Receiver).
OSD Setup Menu exit key when keyboard connects
*
*
5

JOYSTICK OPERATION (Pan/Tilt/Zoom Control)
1. The joystick can be used to control the Fast Dome Camera's left, right, up and down movements.
2 Axis
2. The joystick can be used to control Fast Dome Camera's zoom in and zoom out function.
Stick turn counter-clockwise to zoom out.
Stick turn clockwise to zoom in.
3 Axis
KEYBOARD SYSTEM SETTING
Press SHIFT + SET button to activate the Keyboard system setup menu. Tilt the joystick up or down
to select the menu setup page. Press the 1~11 button to set the number of the desired sub setup item.
Press the ESC button to exit the sub setup item or keyboard system setup menu.
MENU SETUP 1/4
1. KEYBOARD ID
2. SYSTEM MODE
3. PROTOCOL
MENU SETUP 3/4
7. DATE FORMAT
8. DISPLAY
9. TRANSMISSION
MENU SETUP 2/4
4. TONE
5. DATE/TIME
6. SUMMER/TIME
MENU SETUP 4/4
10. INFORMATION
11. BAUD RATE
6
1. KEYBOARD ID
When use multi-keyboard or under MATRIX control mode, have
to setup Keyboard ID.
Press the 1~8 button to set the Keyboard ID number.
KEYBOARD ID SETUP
Select (1-8) for ID
ID=1

With one keyboard, it will be compelled to be the master control and the ID number = 1.
With muti-keyboard, the ID number can not be repeated. The first one will be compelled to be
the master controller and the ID number = 1.
The maximum number of keyboard connections is according to the system mode 8 in PTZ/
Matrix mode, 4 in DVR mode.
2. SYSTEM MODE
Select the system operation mode of the Keyboard controller by
tilting the Joystick left or right to change the operation mode.
(PTZ DVR MATRIX)
3. PROTOCOL
Select the protocol of the operation mode, press the 1~3 button
to select the operation mode.
Press the 1 button to set the protocol type for PTZ mode,
press the 1~5 button to select protocol type.
Press the 1 button to select the protocol for the MLP1
(PIH-7625 etc.)
Press the 2 button to select the protocol for the MLP2
(PIH-7622/35; SP203x/212x etc.)
Push the joystick down to select the next page
Press the 3 button to select the protocol for the MLP2
(PIH-7625T)
Press the 4 button to select the protocol for the PELCO-D
Press the 5 button to select the protocol for the PELCO-P
Push the joystick down to select the next page
Press the 6 button to select the protocol for the PANASONIC SDII CONVENTIONAL
Press the 7 button to select the protocol for the PANASONIC SDII (WV-CS850/860)
Press the 8 button to select the protocol for the PANASONIC SDIII (WV-CS950)
Note: If select the protocol for the PELCO-D/P or PANASONIC CONVENTIONAL / WV-CS850/860
/ WV-CS950, need going to the eleventh item of menu setup to select the transmission speed
(BAUD RATE).
Press the 2 button to set the protocol for DVR mode.
Press the 1 button to select the protocol for PDR-2160.
Press the 3 button to set the protocol for MATRIX mode.
Press the 1 button to select the protocol for PIH-816/832/
864.
Note Once the setup is completed, the display will return back
to previous setup screen. The setup data will be saved on
EEPROM.
ÖÖ
*
*
*
*
*
*
*
*
*
*
SYSTEM MODE SETUP
Move L/R Select Mode
PTZ MODE
PROTOCOL SETUP
1. PTZ
2. DVR
3. MATRIX
PTZ MODE
1. MLP1 (PIH-7625 etc.)
2. MLP2 (PIH-7622/35/
SP203x/212x etc.)
PTZ MODE
3. MLP2 (PIH-7625T)
4. PELCO-D
5. PELCO-P
DVR MODE
1. PDR-2160
MATRIX MODE
1. PIH-816/832/864
7
PTZ MODE
6. SDII CONVENTIONAL
7. SDII (WV-CS850/860)
8. SDIII (WV-CS950)

4. TONE
Keypad tone and Alarm tone ON/OFF control.
Keypad Tone
Press the 1 button to turn on or turn off the buzzer for keypad
tone.
Note Keypad tone ON, when properly operation of keyboard controller, it will send out bi-bi sound
to confirm. If wrongful usage, it will send out bi-bi-bi sound to respond.
However, keypad tone OFF, there is no "bi" sound respond.
S: Start time setting.
E: End time setting.
CORRECT: Correct setting the daylight saving start time.
ENT: Next page.
ESC: Complete the SUMMER/TIME setup.
Note: The setup date format is YY/MM/DD.
Press the 2 button to turn off the daylight saving time setting.
Press the 3 button to clear the daylight saving time setting.
7
Alarm Tone
Press the 2 button to turn on or turn off the siren speaker for alarm tone.
5. DATE / TIME
Date and Time setting, press a number on number pad to enter
the date and time, used the Joystick left or right to move the
cursor position and press the ESC button to finish the setup.
Note The setup Date format is YY/MM/DD.
6. SUMMER/TIME
Daylight saving time function setting.
Press the 1 button to set the daylight saving time setting.
To push the joystick left or right to move the cursor position,
and the press the number key to set the date and time. Then,
press the ENT to next page, or press ESC to complete the
setup.
. DATE FORMAT
Select the Date display format, press the 1~3 button to select
the display format.
8. DISPLAY
Setup Time display ON/OFF.
Time display
Press the 1 button to turn on or turn off the time display on
the LCD.
9. TRANSMISSION
Continue
Press the 1 button to set as continued transmission mode
(per 100 millisecond transmits Protocol once).
TONE SETUP
Press Digit ON/OFF
1. Keypad tone : ON
2. Alarm tone : ON
DATE / TIME SETUP
09/01/01 12 00 00
SUMMER/TIME SETUP
1. ON
2. OFF
3. CLEAR
S: 09/04/05 05:00:00
E: 09/10/25 23:59:00
CORRECT: 06:00:00
PAGE1 ENT: S ESC: C
DATE FORMAT
1. YYYY/MM/DD
2. MM/DD/YYYY
3. DD/MM/YYYY
DISPLAY SETUP
Press Digit ON/OFF
1. Time Display : ON
TRANSMISSION SETUP
1. Continue
2. One shoot
8

One shoot
Press the 2 button to set as single transmission mode. Only when press button, then transmits
the protocol.
10. INFORMATION
Product mode, Joystick type and System version information
display.
11. BAUD RATE
Transmission speed setting.
Press the 1 button to set the baud rate: 9600bps
Press the 2 button to set the baud rate: 4800bps
Press the 3 button to set the baud rate: 2400bps
Push the joystick down to select the next page
Press the 4 button to set the baud rate: 19200 bps
SYSTEM INFORMATION
Product :
Joystick 3 axis
Version : 1.3.0
BAUD RATE SETUP
1. 9600
2. 4800
3. 2400
FAST DOME OPERATIONS
Switch to PTZ Control Mode
Press SHIFT + CAM button to set the keyboard
controller to the PTZ operation mode.
Function keys
F1 To set the speed that Fast Dome Camera travels between preset positions.
F2 To set the dwell time of preset position.
F3 To store the preset data and the save data will be show in the LCD.
F4 To set the preset groups.
SHIFT + F1 180 Horizontal Instant Flip. (Same as key)
SHIFT + F2 Manual speed switch of Zoom, Focus and Iris. (Same as key)
SHIFT + F3 IR Cut Filter Swap. (Same as key)
Menu Setup Using Joystick
Press the SET button to activate the Fast Dome Camera setup menu.
ESC
Move cursor up
1. Decrease a digit
2. Move cursor left
Enter a submenu
Move cursor down
1. Increase a digit
2. Move cursor right
ESC/Exit a setup menu
Call Camera
Enter a number from 1~256 using the number pad and press
the CAM button to select the camera.
Example Call camera #12.
Note The number entered will be show on LCD panel in the format of PTZ mode
ID=XXX.
CAM
SHIFT
2009/01/01 12 00 00
PTZ MODE ID=000
CTRL2
180
SPRAY
ICR
WIPER
LENS
12CAM
2009/01/01 12 00 00
PTZ MODE ID=xxx
MLP2 9600
9
BAUD RATE SETUP
4. 19200

Leave the control over cameras
If no operations from keyboard over 2 minutes, the keyboard
will automatically leave the control over cameras.
Setting Preset Position
Enter a number from 1~128 using the number pad and press the PRESET button to select the
preset position.
Use the joystick to movement the Fast Dome Camera to monitor the desired area.
Enter a number from 1~255 and press the F1 button to set the
Speed value.
Enter a number from 1~255 and press the F2 button to set the
Dwell value.
Press the 1 button and press the F3 button to save the preset
data.
Example Set preset #1.
Select the preset position.
Use the joystick to movement the Fast Dome
Camera to monitor the desired area.
Set the Speed value.
Set the Dwell value.
Save the preset data.
Note Enter a number 9 0 1 1 and press CLR button can clear all preset position data.
Call Preset Position
Enter a number form 1~128 using the number pad and press
the PRESET button to call the preset position.
Example Call preset #1.
Note The preset position data will be show on the LCD panel.
Setting Preset Group
The first 16 preset positions of each Fast Dome Camera are separated into 4 groups.
Preset group must be set for the auto pan reference.
Group 1 includes 1st, 2nd, 3rd and 4th preset positions.
Group 2 includes 5th, 6th, 7th and 8th preset positions.
Group 3 includes 9th, 10th, 11th and 12th preset positions.
Group 4 includes 13th, 14th, 15th and 16th preset positions.
Example 1. To set Group 1
Press the 1 button and press the F4 button to
setting.
2. To set Group 2, 3 and 4
Press the 2, 3, 4 buttons and press the F4 button
to setting.
2009/01/01 12 00 00
PTZ MODE ID=00
2009/01/01 12 00 00
PTZ MODE ID=001
SAVE PRESET 001
DWELL=003 SPEED=255
1PRESET
25 5 F1
3F2
F3
1
1PRESET
2009/01/01 12 00 00
PTZ MODE ID=001
CALL PRESET 001
DWELL=003 SPEED=255
1F4
2009/01/01 12 00 00
PTZ MODE ID=001
PRESET GROUP
SET= 1
2009/01/01 12 00 00
PTZ MODE ID=001
PRESET GROUP
SET= 2+3+4
234
10

PTZ & Lens Control
Pan left
Zoom in
Pan right
Zoom out
FOCUS
FAR
FOCUS
NEAR
Tilt up Tilt down
Zoom in Zoom out
Focus far Focus near
Iris close Iris open
Pan/Tilt/Zoom display information
"Pan_L=000~007" The camera pan left and movement of speed.
"Pan_R=000~007" The camera pan right and movement of speed.
"Pan_U=000~007" The camera tilt up and movement of speed.
"Pan_D=000~007" The camera tilt down and movement of speed.
"Zoom_I =000~015" The camera zoom in and movement of speed.
"Zoom_O=000~015" The camera zoom out and movement of speed.
Note The higher movement values the faster speed.
Alarm Information
When alarm altering, alarm indicator will be blinking and
*
*
*
*
*
*
activate siren speaker (Alarm tone: ON)
at same time. LCD can show 6 alarm information in sequence, the 7th alarm information will
replace 1st alarm information.
Alarm information will not be cleared automatic, and need to press ALARM RESET button to clear
the data.
Note For setting Fast Dome Camera other features or functions, please refer to Fast Dome
Camera Instruction manual.
2009/01/01 12 00 00
PTZ MODE ID=001
Pan_L=000 Tilt_U=007
Zoom_I=015
2009/01/01 12 00 00
PTZ MODE ID=001
ID=001 Alarm No=001
ID=001 Alarm No=002
Matrix and Receiver Operations
Switch to MATRIX Control Mode
Press SHIFT + MATRIX button to set the keyboard controller
to the Matrix operation mode.
MATRIX
SHIFT
2009/01/01 12 00 00
MATRIX MODE
11

Function Keys
F1 Turn on/off the on-screen display (time, date and camera number).
F2 Display the list of last 10 alarms or video loss alarms information on the monitor.
F3 Adjust the position of the on-screen display.
F4 Set the P/T/Z preset position groups.
KEYBOARD ID Setting
Under MATRIX mode, need to setup keyboard ID. (Please refer to keyboard system setup)
Prompt " "
Matrix System can only be controlled and operated when
" " sign is displayed.
Enter a number form 1~16 using the number pad and press
MON button to select the monitor and the " " control sign
appear on the monitor signaling the system is ready for
setup or operation.
The " " control sign will disappear automatically when
there isn't any operation or setting for 5 minutes.
Menu Setup Mode
Press the SET button under " " control sign to activate the Matrix setup menu.
MON 01 <H>
CAM 01>CAMERA01
<
01/01/09
17:28:01
Control Sign
ESC
Save and Exit menu ESC/Exit a submenu
Use the 0~9 numeric keys to set the number of the
desired submenu or setup data.
9
0
Call Monitor
Enter a number form 1~16 using the number pad and press the MON button to select the monitor.
Example Call monitor #2
Note The number entered will be show on the Monitor.
Call Camera
Enter a number form 1~64 using the number pad under " " control sign and press the CAM button
to select the camera.
Example Call camera #12
PTZ Control via Matrix
To control PTZ camera in matrix, perform call camera in the preset monitor.
Once a camera of a monitor gets controlled, the following PTZ operations can be performed.
2MON
12CAM
12

Pan left
Zoom in
Pan right
Zoom out
FOCUS
FAR
FOCUS
NEAR
Tilt up Tilt down
Zoom in Zoom out
Focus far Focus near
Iris close Iris open
Auto pan
AUTO
PAN CTRL2
180
CTRL1
C.SET
SPRAY
ICR
WIPER
LENS
LIGHT
C.ESC
180 Reverse
Camera Menu Setup Camera Menu Esc
Lens Speed Swap IR Cut Filter Swap
Note To enter Fast Dome setup menu under Matrix control mode, must press key after " "
control sign, and press key to exit setup mode.
Alarm Information
If alarm is trigged under matrix control mode, keyboard controller will not respond the alarm
information. The alarm information will only show on monitor of matrix.
Note For setting Matrix other features or functions, please refer to PIH-816/832/864 Instruction
manual.
CTRL1
C.SET
LIGHT
C.ESC
DVR OPERATIONS
There are four main DVR features including multiplexer, menu setup, PTZ control and playback
controllable by the keyboard controller.
Switch to DVR Control Mode
Press the SHIFT button and the DVR button to set the
keyboard controller to the DVR operation mode.
DVR Multiplexer Features
Control DVR
Enter a number from 1~255 using the number pad and press
DVR button to select the DVR.
Example Control DVR #12
Note The number entered will be shown on the LCD panel in the format of DVR MODE ID=xxx.
DVR
2009/01/01 12 00 00
DVR MODE ID=000
DVR
SHIFT
12
2009/01/01 12 00 00
DVR MODE ID=xxx
13

Call Camera
After a DVR gets controlled, enter a number from 1~16 using the number pad and press the
CAM button to select the camera.
Example Call camera #8 of DVR #12
Direct to access a camera of a particular DVR
Enter the camera's ID (1~4080) and press CAM button. Then camera ID gets resolved
(divided by 16) to its DVR by keyboard controller.
Example 1. Call camera #17
Enter camera number 17 and press the CAM
button. (DVR #2's first camera).
2. Call camera #128
Enter camera number 128 and press the
CAM button. (DVR #8's camera #16)
Window-Division Mode
To perform window division feature of a DVR, press the following window
division buttons.
16 window-division.
9 window-division.
8 window-division.
4 window-division.
DVR Sequential Display
Press SEQ button to display camera's full screen in a sequence with specific time period.
DVR Menu Setup
After a DVR gets controlled, press the SET button to activate the DVR's setup menu.
*
7
1CAM
8
2
1CAM
8
0CAM
DVR
12
2009/01/01 12 00 00
DVR MODE ID=002
CAM=001
CALL CAMERA 017
2009/01/01 12 00 00
DVR MODE ID=008
CAM=016
CALL CAMERA 128
ESC
Move cursor up
Enter a submenu
Move cursor down
ESC/Exit a submenu
Enter a submenu ESC/Exit a submenu
Decrease a digit Increase a digit
DVR Playback
To perform DVR playback feature, press PLAY button or SEARCH button.
PLAY button can invoke playback menu. Use 3D joystick to move menu cursor and perform
playback feature.
SEARCH button can invoke time search feature of the DVR. Use 3D joystick to move menu
cursor.
*
*
14

Move cursor down
1. Enter a submenu in playback menu
2. Fast forward video in playback mode ESC/Exit a submenu
Decrease a digit Increase a digit
1. ESC/Exit a submenu in playback
menu
2. Fast reverse video in playback mode
Video Playback Operations
Pause
Press PAUSE button during playing video can pause the video in pause mode.
Play
Replay the video after Pause, Fast Forward or Fast Rewind.
Fast Forward
Fast forward the playback video.
Fast Rewind
Fast rewind the playback video.
Stop
Stop the playback video and return to playback menu.
Record / Stop Record
Perform DVR record or stop DVR recording operation.
Note Select various split display modes on live and playback monitoring.
*
*
*
*
*
*
PTZ Control via DVR
To control PTZ camera in live monitoring mode, press ENTER button to gain camera control
sequentially in window-division mode or perform call camera in full screen mode.
Once a camera of a DVR gets controlled, the following PTZ operations can be performed.
Pan left
Zoom in
Pan right
Zoom out
FOCUS
FAR
FOCUS
NEAR
Tilt up Tilt down
Zoom in Zoom out
Focus far Focus near
Iris close Iris open
Auto pan
AUTO
PAN
Recall a Preset
To recall a preset point of a PTZ device , please number key and followed by PRESET key.
Example Recall 16 preset of camera #21
Note For setting PTZ presets, other features or functions, please refer to DVR Instruction Manual.
PRESET
1
26
CAM
1
15

Keyboard Controller
PIH-931D/932T
INSTRUCTION MANUAL
WIRING DIAGRAM
Connecting Keyboard Controller and Connector Box.
RJ-45 and Connector Box Pin Assignment.
18
27
36
45
12345678
RJ-45
Connector Box
Terminal
1
2
3
4
5
6
7
8
Name
DC +12V input
GND
RS-485 +
RS-485 + OUT
RS-485 + IN
RS-485 -
RS-485 - OUT
RS-485 - IN
DVR
Link Keyboard
PTZ or Matrix
PTZ or Matrix
DVR
Link Keyboard
12345678
18
27
36
45
RJ-45 Cable
Twin Pair Cable
DVR
Twin Pair Cable
Twin Pair Cable
Link Keyboard
PTZ
(Fast Dome Camera)
DC12V Adaptor
Keyboard Controller
Power Adaptor
Connector Box RJ-45 Connection Cable
User's Instruction Manual
16
PRODUCT COMPONENTS

SYSTEM OVERVIEW
PTZ (Fast Dome Camera) System Block
Matrix System Block
MATRIX
PIH-864
CAM 1 CAM 2 CAM 64
RS-485
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
Keyboard 1 Keyboard 2 Keyboard 8
Monitor 1 Monitor 2 Monitor 16
MATRIX
RS-485
DVR System Block
HDD USBREC AL POWER
REW
BACKUP ESC MENU
JOG SHUTTLE
67
910
11 12 13 14 15
5
3
1 42 8
16
FF
REC
HDD USBREC AL POWER
REW
BACKUP ESC MENU
JOG SHUTTLE
67
910
11 12 13 14 15
5
3
1 42 8
16
FF
REC
HDD USBREC AL POWER
REW
BACKUP ESC MENU
JOG SHUTTLE
67
910
11 12 13 14 15
5
3
14
28
16
FF
REC
CAM 1 CAM 1 CAM 1CAM 16 CAM 16 CAM 16
VIDEO
VIDEO
Monitor 1 Monitor 2 Monitor 16
RS-485 RS-485 RS-485
VIDEO VIDEO VIDEO
VIDEO VIDEO VIDEO
RS-485 RS-485
DVR 1 DVR 2 DVR 16
RS-485
VIDEO
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
Keyboard 1
(ID = 1)
CAM 1 CAM 2 CAM 256
RS-485
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
Keyboard 2
(ID = 2)
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
Keyboard 8
(ID = 8)
POWER
ALARM
R/T
06/02/15 12 00 00
PTZMODE ID=000
POWER
ALARM
R/T
06/02/15 12 00 00
PTZMODE ID=000
POWER
ALARM
R/T
06/02/15 12 00 00
PTZMODE ID=000
POWER
ALARM
R/T
06/02/15 12 00 00
PTZMODE ID=000
Keyboard 1
(ID = 1)
Keyboard 2
(ID = 2)
Keyboard 3
(ID = 3)
Keyboard 4
(ID = 4)
RS-485
17

PTZ (Fast Dome Camera) System Wiring
Matrix and PTZ (Fast Dome Camera) System Wiring
VIDEO INVIDEO IN
RS232
RECEIVER
KEY BOARD
VIDEO OUT
VIDEO OUT
ALARM IN AALARM IN A
ALARM IN BALARM IN B
AC INAC IN
1
2
3
4
5 10
9
8
7
6
15
14
12
13
11 16
17
18
19
20 3025
2924
2823
2722
2621
50454035
49443934
48433833
47423732
46413631 51 56 61
52 57 62
53 58 63
54 59 64
55 60
1
2
3
4 8
7
6
5
10
9
11
12 16
15
14
13
AUTO
12345678
DOWN
UP
LEFT
RIGHT
COMMON
L
N
VIDEO
OUT
VIDEO
OUT
AC
INPUT
AC
OUTPUT 2
AC
OUTPUT 1
AUX 2
AUX 1
WIPER
SPRAY
LIGHT
PAN/TILT
LNE LNE LNE
LNE
SL
FH
HW
IRIS
FOCUS
ZOOM
+
-
GND
+
-
TXD
IN
TXD
OUT
12V GND
-4V -9V
4V
9V
230 (117) V
24V
COM
PC
TXDO+
TXDO-
RS-485
RS-485
RS-232
RS-485
POWER
ALARM
R/T
06/02/15 12 00 00
PTZMODE ID=000
18
27
36
45
GND
DC-12V
POWER
ALARM
R/T
06/02/15 12 00 00
PTZMODE ID=000
18
27
36
45
GND
DC-12V
CAM
Receiver
MATRIX
Keyboard
Controller
Keyboard
Controller
AC
SWITCHING
POWER
24Vac
90~260Vac
()
CAM
VIDEO
Monitor
ADAPTOR
Keyboard 1
RS-485
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
18
27
36
45
AC
GND
DC-12V
ADAPTOR
Keyboard 2
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
18
27
36
45
AC
ADAPTOR
Keyboard 8
POWER
ALARM
R/T
06/02/15 12 00 00
PTZ MODE ID=000
18
27
36
45
AC
18
TXDI+
TXDI-
TXDO-
TXDO+
GND
TXDI+
TXDI-
TXDO-
TXDO+
GND