TECH EU-R-8z User manual
user’s manual
EU-R-8z
user’s manual
EU-R-8z
SERWIS
32-652 Bulowice,
ul. Skotnica 120
Tel. +48 33 8759380, +48 33 3300018
+48 33 8751920, +48 33 8704700
Monday - Friday
7:00 - 16:00
Saturday
9:00 - 12:00
TECH STEROWNIKI
Spółka z ograniczoną odpowiedzialnością SP.k.
Biała Droga 31
34-122 Wieprz
WARRANTY CARD
TECH company ensures to the Buyer proper operation of the device for the period of 24 months from the date of sale. The Guarantor
undertakes to repair the device free of charge if the defects occurred through the manufacturer’s fault. The device should be delivered to its
amendments of the Civil Code (Journal of Laws of 5 September 2002).
CAUTION! THE TEMPERATURE SENSOR CANNOT BE IMMERSED IN ANY LIQUID (OIL ETC). THIS MAY RESULT IN DAMAGING THE CONTROLLER
AND LOSS OF WARRANTY! THE ACCEPTABLE RELATIVE HUMIDITY OF THE CONTROLLER’S ENVIRONMENT IS 5÷85% REL.H. WITHOUT THE STEAM
CONDENSATION EFFECT.
THE DEVICE IS NOT INTENDED TO BE OPERATED BY CHILDREN.
Activities related to setting and regulation of the controller parameters described in the Instruction Manual and parts wearing out during normal
operation, such as fuses, are not covered by warranty repairs. The warranty does not cover damages arising as a result of improper operation or
protective seals. Removing a seal results in the loss of Warranty.
the equipment through the fault of the client or not subject to Warranty), or if the device defect occurred for reasons lying beyond the device.
VAT invoice, etc.). The Warranty Card is the only basis for repair free of charge. The complaint repair time is 14 days. When the Warranty Card is lost
or damaged, the manufacturer does not issue a duplicate.
...................................... ......................................
seller’s stamp date of sale
Safety
carefully. Not obeying the rules included in this manual may lead to personal injuries
or controller damage. The user’s manual should be stored in a safe place for further
reference. In order to avoid accidents and errors it should be ensured that every person
using the device has familiarized themselves with the principle of operation as well
place, make sure that the user’s manual is there with the device so that any potential
user has access to essential information about the device. The manufacturer does not
accept responsibility for any injuries or damage resulting from negligence; therefore,
users are obliged to take the necessary safety measures listed in this manual to protect
their lives and property.
WARNING
Wearecommittedtoprotectingtheenvironment.Manufacturing
electronic devices imposes an obligation of providing for
environmentally safe disposal of used electronic components
and devices. Hence, we have been entered into a register
kept by the Inspection For Environmental Protection. The
crossed-out bin symbol on a product means that the
product may not be disposed of to household waste
containers. Recycling of wastes helps to protect the
environment. The user is obliged to transfer their used
equipment to a collection point where all electric and
electronic components will be recycled.
Technical data
Range of room temperature settings...........................................5-35C
Power supply ................................................................................6V
Power consumption.....................................................................0,7W
Accuracy of measurement.......................................................+/-0,5C
Frequency..............................................................................868MHz
Description
controller.
EU-R-8z room regulators are installed in the heating zones. Temperature
thermostatic valves (by opening them when the room temperature is
too low and closing them when the pre-set room temperature has been
reached).
Current temperature is shown on LED display. The user may also change
the preset temperature permanently or for a limited period of time
directly from the sensor.
Controller equipment:
LED display
built-in temperature sensor
wall-mountable cover
light sensor
Installation
WARNING
Risk of fatal electric shock from touching live connections.
and prevent it from being accidentally switched on.
WARNING
Incorrect connection of the wires may damage the regulator!
How to register the room regulator in a
particular zone
Each room regulator should be registered in one zone. Enter EU-L-8
zone (Zone/Registration/Sensor)- after pressing the Registration icon,
press the communication button in a room regulator placed on the back
of the sensor.If the registration process has been completed successfully,
EU-L-8 controller display shows an appropriate message whereas the
room sensor display shows “Scs”. In case of errors in the registration
process, the room sensor display shows “Err”.
The following rules must be kept in mind:
- once registered, the sensor cannot be unregistered, but only switched
the submenu of a given zone.
- if the user attempts to assign a sensor to the zone to which other sensor
is replaced by the second one.
- if the user attempts to assign a sensor which has already been assigned
registered in the new one.
It is possible to set individual pre-set temperature value and weekly
schedule for each
Sensors) and via www.emodul.eu (using ST-507 or WiFi RS). The pre-set
temperature may also be adjusted directly from the room sensor using
PLUS and MINUS button.
How to change the pre-set temperature
The pre-set zone temperature may be adjusted directly from R-8z room
sensor using PLUS and MINUS buttons.
During controller inactivity, the main screen displays current zone
temperature. After pressing PLUS or MINUS, the current temperature is
PLUS and MINUS the user may adjust the preset temperature value.
After setting desired value wait for 3 seconds – after this time the display
Time settings may be adjusted:
- permanently – press PLUS button until Con appears on the screen
(the pre-set value will apply all the time regardless of schedule settings)
number of hours appears on the screen e.g. 01h (the pre-set value will
apply)
apply, press MINUS until the screen displays OFF.
EU Declaration of Conformity
Wieprz, is compliant with:
Directive 2014/53/EU of the European parliament and of the Council of 16 April 2014. on the harmonisation of the laws of the Member States
relating to the making available on the market of radio equipment;
Directive 2009/125/EC establishing a framework for the setting of ecodesign requirements for energy-related products;
the regulation by the Ministry of Economy of May 8, 2013 ‘concerning the essential requirements as regards the restriction of the use of certain
hazardous substances in electrical and electronic equipment’, implementing provisions of ROHS directive 2011/65/EU
.
For compliance assessment, harmonized standards were used:
PN-EN 60730-2-9 :2011 par. 3.1a Safety of use
ETSI EN 301 489-1 V2.1.1 (2017-02) par.3.1b Electromagnetic compatibility
ETSI EN 301 489-3 V2.1.1 (2017-03) par.3.1 b Electromagnetic compatibility
Wieprz, 06.12.2018
230V 50Hz
Power
Supply
6V DC
Table of contents
Other TECH Controllers manuals
TECH
TECH ST-77 Assembly instructions
TECH
TECH ST-81 User manual
TECH
TECH ST-408N User manual
TECH
TECH ST-22 User manual
TECH
TECH EU-R-8b User manual
TECH
TECH Sinum WSS-22 User manual
TECH
TECH ST-26 Assembly instructions
TECH
TECH ST-2640 User manual
TECH
TECH EU-21DHW User manual
TECH
TECH SINUM PS-10 230 User manual
