Lincoln 3624 User manual

Used oil receiver
Model 3624
User guide
Read manual prior to installation or use
of this product. Keep manual nearby for
future reference. Failure to follow
instructions and safety precautions may
result in death or serious injury.
Danger
Date of issue October 2014
Form number 404087D
Section B4
Page 31D

Owner/operator
responsibility
It is the owner/operator responsibility to
properly use and maintain this equipment.
The instructions and warnings contained
in this manual shall be read and understood
by the owner/operator prior to operating this
equipment.
The owner/operator shall retain this
manual for future reference to important
warnings, operating and maintenance
instructions.
Safety
The standards listed below must be
observed to prevent injury to operators and
damage to the used oil receiver.
Inspection
Prior to operation or maintenance, a visual
inspection shall be made. Check for worn
parts, air leaks, damaged, loose or missing
parts.
Check tank operation by connecting air to
air nipple and closing ball valve. Verify that
there is sufficient air flow coming from
nozzle/hose assembly.
If the unit is damaged, badly worn or
operates abnormally, it should be removed
from service. Contact a factory authorized
service center for repair.
An annual tank/component inspection is
recommended to be performed by a factory
authorized service center.
Cleaning and
maintenance
The used oil receiver does not require any
special maintenance, other than normal
cleaning, which should be done with a damp
cloth (water and alcohol or normal detergent
for household appliances made out of
plastic).
• Read all labels on the used oil receiver
carefully, do not cover them and replace
them immediately if damaged.
• The used oil receiver must only be used
by authorized personnel trained in its use.
• Never leave unit unattended when oper-
ating or evacuating.
• Never use near open flame or heat
source.
• Always disconnect air supply after
emptying.
• Never use unit for handling highly volatile
fuels and fluids.
• Use only the nozzle assembly provided.
• Pay attention to other people in the vicin-
ity while the used oil receiver is operating,
especially children.
• Do not use the used oil receiver in an en-
vironment subject to explosion hazard.
• Do not use the used oil receiver as a
means of transport.
• Do not use acid solutions which could
damage the used oil receiver and/or injure
persons.
• The used oil receiver will remain in place
up to a maximum gradient of 0.5%,
before beginning to slide.
• If the used oil receiver malfunctions, con-
tact the dealer or send it to the nearest
service center.
• When replacing parts, always demand
original replacement parts from an
authorized Lincoln dealer or retailer.
Specifications
Tank capacity 105.7 qts. (100 l)
Top of sight tube 95 qts. (90 l)
Drain bowl capacity 17 qts. (16 l)
Height at highest
position
78.5 in. (199.39 cm)
Height at lowest
position
51.25 in. (130.,8 cm)
!Notice
This device dispenses fluid using
pressurized air, and complies with speci-
fications of Uniform Fire Code, Standard
Fire Prevention Code and National Fire
Protection Association, (NFiPA-30). It
does not comply with current provisions
of BOCA section F.5.3. Consult your local
fire marshall concerning code compli-
ance of this device.
!Notice
Do not use cleaning solutions that
can damage plastic containers.
!Notice
Regulator maintains pressure of
air to used oil receiver, no more than
7.5 psi (0,5 bar). Tampering with or
removing regulator will void warranty.
2

Operation
To position the oil drain bowl, loosen locking
ring, raise the drain bowl to the desired
position and retighten.
Level indicator shows the quantity of oil in
the tank.
31
28
20
10
13
17
10
28 4
31
!Notice
When draining the oil from the
vehicle, open valve (10) to allow the oil
to flow into the tank and open valve (28)
to allow air to vent as tank fills.
Emptying tank
1 Close ball valve (10).
2 Connect compressed air to air nipple (30)
open ball valve (28) allowing tank to
pressurize up to maximum pressure
7.25 psi (0,5 bar).
3 Fasten drain pipe (20) to the used oil
drum.
4 Open ball valve (31).
5 Once emptying is complete, disconnect
compressed air and close ball valve (31).
6 Re-open ball valve (10).
!Notice
Never fill tank over maximum
level given by level indicator (17).
Receiver full when level (17) is 1/8 in.
(3,175 mm) below fitting.
!Notice
The waste oil receiver is fitted
with a safety valve (13), calibrated to
14.5 psi (1 bar).
3

1
2
3
4
5
6
7
12
13
14
15
16
17
18
19
20
21
22
5.02 in. (127,5 mm)
8*
9
10
11
Ø 17.52 in.
(Ø 445 mm)
23
24
25
26
27
28
29
30
28
31
32
33
34*
4

Service parts
Item no. Description Part number Qty Item no. Description Part number Qty
1 Warning label 247130 1 18 Rear wheel set 274462 2
2 Cover bushing 274446 1 19 Axle 274459 1
3 O-ring 274471 4 20 Drain hose 274007 1
4 Ring nut kit 273995 1 21 Name plate 274106 1
5 Elastic ring 274470 1 22 Operating instructions 274105 1
6 Screen 273988 1 23 Upper o-ring 275508 1
7 Operating label 274021 1 24 Pipe 273994 1
8 Logo label 412877* 1 25 Drain cap 274454 1
9 Kit, funnel and bushing 275296 1 26 Upper connection 274458 1
10 Ball valve 273992 1 27 Fitting 274474 2
11 Ring nut kit 276284 1 28 Ball valve 274451 2
12 Cap 274448 1 29 Fitting, level hose 274449 1
13 Safety valve 274447 1 30 Air nipple 11659 1
14 Regulator 274005 1 31 Ball valve 274008 1
15 Ta n k 274460 1 32 Elbow 274009 1
16 Warning label 420036 1 33 Lower connection 274456 1
17 Level hose 274000 1 34 Caster wheel set 274453* 2
*Indicates change
5

Lincoln industrial
standard warranty
Standard limited warranty
Lincoln warrants the equipment manufac-
tured and supplied by Lincoln to be free
from defects in material and workmanship
for a period of one (1) year following the
date of purchase, excluding there from any
special, extended, or limited warranty pub-
lished by Lincoln. If equipment is deter-
mined to be defective during this warranty
period, it will be repaired or replaced, within
Lincoln’s sole discretion, without charge.
This warranty is conditioned upon the
determination of a Lincoln authorized rep-
resentative that the equipment is defective.
To obtain repair or replacement, you must
ship the equipment, transportation charges
prepaid, with proof of purchase to a Lincoln
Authorized Warranty and Service Center
within the warranty period.
This warranty is extended to the original
retail purchaser only. This warranty does not
apply to equipment damaged from accident,
overload, abuse, misuse, negligence, faulty
installation or abrasive or corrosive material,
equipment that has been altered, or equip-
ment repaired by anyone not authorized by
Lincoln. This warranty applies only to equip-
ment installed, operated and maintained in
strict accordance with the written specifica-
tions and recommendations provided by
Lincoln or its authorized field personnel.
This warranty is exclusive and is in lieu
of any other warranties, express or
implied, including, but not limited to, the
warranty of merchantability or warranty
of fitness for a particular purpose. War-
ranty on items sold by Lincoln, but not
manufactured by Lincoln are subject to
the warranty consideration, if any, of
their manufacturer (such as hoses,
hydraulic and electric motors, electrical
controllers, etc.) Assistance in making
such warranty claims can be offered as
required.
In no event shall Lincoln be liable for inci-
dental or consequential damages. Lincoln’s
liability for any claim for loss or damages
arising out of the sale, resale or use of any
Lincoln equipment shall in no event exceed
the purchase price. Some jurisdictions do
not allow the exclusion or limitation of inci-
dental or consequential damages, therefore
the above limitation or exclusion may not
apply to you.
This warranty gives you specific legal
rights. You may also have other rights that
vary by jurisdiction.
Customers not located in the Western
Hemisphere or East Asia: Please contact
Lincoln GmbH and Co. Kg, Walldorf,
Germany, for your warranty rights.
Special limited warranties
Special limited 2 year warranty
SL-V series, single injectors – 85772,
85782, and replacement injectors –
85771, 85781
Lincoln warrants the SL-V Injector series to
be free from defects in material and work-
manship for two (2) years following the date
of purchase. If an injector model (single or
replacement) is determined to be defective
by Lincoln, in its sole discretion, during this
warranty period, it will be repaired or
replaced, at Lincoln’s discretion, without
charge.
Special limited 5 year warranty
series 20, 25, 40 bare pumps, pmv bare
pumps, heavy duty and 94000 series bare
reels
Lincoln warrants series 20, 25, 40 bare
pumps, PMV bare pumps, heavy duty
(82206), mini bench (81133, 81323), and
all 94000 LFR series (single arm and dual
arm) bare reels to be free from defects in
material and workmanship for five (5) years
following the date of purchase. If equipment
is determined by Lincoln, in its sole discre-
tion, to be defective during the first year of
the warranty period, it will be repaired or
replaced at Lincoln’s discretion, without
charge. In years two (2) and three (3), the
warranty on this equipment is limited to re-
pair with Lincoln paying parts and labor
only. In years four (4) and five (5), the war-
ranty on this equipment is limited to repair
with Lincoln paying for parts only.
Special limited 5 year warranty
limited oil meters, limited fluid control
valves, aod (air-operated diaphragm
pumps)
Lincoln warrants the 712 series control
valves, 912 series lube meters, electronic
lube meters (980, 981, 982 series), our
universal inline digital meters (812/813
series), and our AOD pump offering to be
free from defects in material and workman-
ship for five (5) years following the date of
purchase. If either is determined to be
defective by Lincoln, in its sole discretion,
during the warranty period, they will be
repaired or replaced, at Lincoln’s discretion,
without charge.
Special DEF (diesel exhaust fluid) limited
warranty
DEF products are warranted to be free from
defects in material and workmanship for a
period of one (1) year following the date of
purchase. The following exceptions to the
standard warranty period are in effect:
• 85700-30/85700-50 DEF hose reels
(bare reel only),
277251/277252 AC DEF pumps, and
277256 and 277257 DEF meters are
warranted for two (2) years from date of
purchase.
• 85623 DEF AOD
(air operated diaphragm) pumps
are covered under the standard five (5)
year AOD pump warranty.
If either is determined to be defective by
Lincoln, in its sole discretion, during the
warranty period, they will be repaired or
replaced, at Lincoln’s discretion, without
charge.
Lincoln Industrial contact information
To find Lincoln Industrial’s nearest service
center call the following number;
customer service 314-679-4200
(international number 01-314-679-4200)
or you may also use our website
www.lincolnindustrial.com
6

This page left intentionally blank.
7

® SKF is a registered trademark of the SKF Group.
® Lincoln is a registered trademark of Lincoln Industrial Corp.
© SKF Group 2014
The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permis-
sion is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be
accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
SKF PUB LS/I4 15243 EN.R1 · October 2014 · Form 404087D
Seals Bearings and
housings
Lubrication
systems
Mechatronics Services
The Power of Knowledge Engineering
Combining products, people, and application-
specific knowledge, SKF delivers innovative
solutions to equipment manufacturers and pro-
duction facilities in every major industry world-
wide. Having expert ise in multiple competence
areas supports SKF Life Cycle Management, a
proven approach to improv ing equipment reliabil-
ity, optimizing operational and energy efficiency
and reducing total cost of ownership.
These competence areas include bearings and
units, seals, lubrication systems, mecha tronics,
and awide range of services, from 3-D computer
modelling to cloud-based condition monitoring
and asset management services.
SKF’s global footprint provides SKF customers
with uniform quality standards and worldwide
product availability. Our local presence provides
direct access to the experience, knowledge and
ingenuity of SKF people.
SKF BeyondZero is more than our climate strategy
for a sustainable environment: it is our mantra; a
way of thinking, innovating and acting.
For us, SKF BeyondZero means that we will
reduce the negative environmental impact from
our own operations and at the same time, increase
the positive environmental contri bution by offering
our customers the SKF BeyondZero portfolio of
products and services with enhanced envir on-
mental performance characteristics.
For inclusion in the SKF BeyondZero portfolio,
aproduct, service or solution must deliver signifi-
cant environmental benefits without serious
envir onmental trade-offs.
lincolnindustrial.com skf.com/lubrication