Linear Lb60z-1 User manual

LB60Z-1

Radio Frequency Controlled

Smart LED Light Bulb

NOTE: This unit must be “included in the Network” only where it will be permanently installed. The proper operation of this node in the mesh

network is dependent on it knowing its location with respect to other nodes.You cannot “test bench” conﬁgure this bulb, then install.

LB60Z-1 SMART LED LIGHT BULB

Linear’s family of LinearLinc®Z-Wave®certiﬁed wireless lighting products

(smart LED bulbs, switches, dimmers, outlets, and plug-in modules) and

security devices (alert sounder, passive infrared sensor and door/window

transmitter) bring a new level of intelligent wireless capability to commercial

and residential environments.

The Z-Wave wireless protocol is an international wireless standard for remote

home automation, security and other applications. Embedded in each device,

the Z-Wave smart chip enables two-way RF communication among hundreds

of Z-Wave enabled devices, allowing products and services from multiple

manufacturers to work seamlessly.

The LB60Z-1 Smart LED Light Bulb is simple to set up and provides longer

life and more energy efﬁciency than incandescent or ﬂorescent light bulbs. The

bulb is instant on, without the warm-up delay common in CFL bulbs.

LinearLinc Z-Wave products are easy to install, and allow dealers to create an

integrated wireless network with nearly limitless expansion and interoperability

with security, energy management, home entertainment, appliances, and more.

As part of a Z-Wave network, the LB60Z-1 will also act as a wireless repeater to

insure that commands intended for another device in the network are received.

This is useful when the device would otherwise be out of the radio range of the

wireless controller.

For indoor use only. Retain instructions for future use.

INSTALLATION

1. At the selected location, turn the power to the light bulb socket OFF.

2. Screw the Smart LED Light Bulb into the lamp socket.

For “Inclusion” to (adding to) a network:

Refer to your Controller operating instructions to add this bulb under the

command of the Wireless Controller.

1. With your controller in Inclusion Mode, turn the power to the light bulb

socket ON.

2. You should see an indication on your Controller that the “device was

included” in the network. The Smart LED Light Bulb will ﬂash twice.

3. The device will appear in the list of Switches. It should display multi-level

switch / Linear.

If the Controller/Gateway shows the inclusion failed, repeat Steps 1-3.

✓NOTE: If you have trouble adding the LB60Z-1 to a group it may be that the Home

ID and Node ID were not cleared from it after testing.You must ﬁrst “RESET UNIT” to

remove it from the network. Although adding it to a group includes it in the network,

removing it from a group does not remove it from the network. If removed from a

group, it functions as a repeater (only). “RESET UNIT” removes it completely from

the network.

To Reset Unit (If Required)

To reset the bulb and clear all network information, follow these steps:

1. Use the wall switch to turn the power to the bulb ON then OFF four times

within four seconds.

2. The Smart LED Light Bulb will ﬂash twice when the reset occurs.

Before repeating the steps above, try moving the Smart LED Light Bulb to

a socket in the same room as the Controller/Gateway in case the preferred

socket is out of range initially.

Repeat Steps 1-3 above until the Smart LED Light Bulb is added to the

network. Once the bulb has been successfully added to the network, move it

to the preferred location.

For “Exclusion” from (removing from) a network:

The Smart LED Light Bulb can be excluded from the network by the Controller/

Gateway. Refer to the Controller operating instructions for details.

1. Set the Controller into “exclusion” mode, and following its instruction to

delete the LB60Z-1 from the Controller.

2. Reset the bulb by using the wall switch to turn the power to the bulb ON. The

Smart LED Light Bulb will ﬂash twice to conﬁrm the exclusion.

750 Lumens

Equivalent

to a 60 Watt

incandescent

light bulb

Z-Wave®is a registered trademark of Sigma Designs

BASIC OPERATION

Remote Control Operation

The Smart LED Light Bulb can be controlled ON / OFF/ BRIGHT / DIM through

wireless signals from the Z-Wave remote controller or through a gateway via an

application on a smart phone, tablet, or PC.

Once the Smart LED Light Bulb has been added to the network,depending on

the functions supported by your controller, it can be assigned to a Group or

Scene and operate when the ALL ON or ALL OFF command is received from

the Controller. It can also be set in Association with another Z-Wave device to

perform a speciﬁc duty.

Manual Operation

The Smart LED Light Bulb can be manually operated using the wall switch while

keeping it on-line with the Z-Wave network.

To manually turn the Smart LED Light Bulb ON:

Flip the wall switch OFF then ON. Be sure the switch is ON when ﬁnished.

To manually turn the Smart LED Light Bulb OFF:

Flip the wall switch OFF then ON twice within two seconds. Be sure the switch

is ON when ﬁnished.

CONFIGURATION

The LB60Z-1 supports the Conﬁguration command. The LB60Z-1 can be

conﬁgured to operate slightly differently than how it works when you ﬁrst install

it. Using the Conﬁguration command you can conﬁgure the following:

Parameter 1: Dim Level Memory

By default, the LB60Z-1 bulb will go to full brightness when turned on. To have

the bulb turn on to the last dim level setting, set parameter 1 to 1.

• Parameter No: 1

• Length: 1 Byte

• Valid Values = 0 (default) or 1.

• When the value = 0, the bulb will be full brightness when turned on.

• When the value = 1, the bulb will turn on to the last dim level setting.

Z-Wave Plus Features

The LB60Z-1 contains a Z-Wave 500 Series Module that supports Z-Wave Plus

features. A Z-Wave certiﬁed portable or stationary controller can communicate

with the Z-Wave 500 Series Module.

Depending on the capability of the controller or gateway software, the following

operations can be performed with the Smart LED Light Bulb. Refer to the

controller or gateway manual for details.

• Turn the bulb ON and OFF.

• Dim the bulb.

• Add (Include) or Delete (Exclude) the Smart LED Light Bulb.

• Assign the Smart LED Light Bulb to a specific Group/Scene and/or to include

the bulb as part of ALL ON or ALL OFF system commands.

• Over-the-air firmware update by the gateway or static controller.

• Lifeline function which automatically notifies the associated modules and the

network that a manually reset device is no longer in the network, thus, the

corresponding association becomes invalid.

INTEROPERABILITY WITH Z-WAVE DEVICES

A Z-Wave network can integrate devices of various classes of products, and

these devices can be made by different manufacturers. The LinearLinc Smart

LED Light Bulb has Z-Wave certiﬁcation which guarantees interoperability.

ASSOCIATION

The LB60Z-1 supports one Group with ﬁve Nodes for lifeline communication.

Group 1 must be assigned the Node ID of the controller to which unsolicited

notiﬁcations from the LB60Z-1 will be sent.The Z-Wave controller should set this

association automatically after inclusion. You can associate up to ﬁve Z-Wave

devices to Group 1. Lifeline association only supports the “manual reset” event.

For instructions on how to “set lifeline association” please refer to your wireless

controller instructions.

SPECIFICATIONS

Power Supply 120 VAC, 60 Hz

Brightness 750 lumens (Equivalent to 60 Watt

incandescent light bulb)

Power Consumption 9 Watts

Color Temperature 2700K

Bulb Lifetime 25,000 hour (equivalent 22.8 years based

on 3 hours/day)

Radio Frequency 908.4 MHz / 916 MHz

Wireless Range Up to 130 feet line of sight between the

Z-Wave Controller and/or the closest

Z-Wave Repeater

Normal Operating Temp 77°F (25°C)

Repeater Ye s

REGULATORY INFORMATION

The LB60Z-1 is certiﬁed to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions.

FCC ID: EF400126 IC #: 1078A-00126

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any interference received, including interference

received that may cause undesired operation.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician to help.

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment

IC Notice

This Class B digital apparatus complies with Canadian ICES-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme

aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. This warranty

extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels.

Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the

nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for

consequential damages arising out of or in connection with use or performance of this product or other indirect

damages with respect to loss of property, revenue, or proﬁt, or cost of removal, installation, or reinstallation.

All implied warranties, including implied warranties for merchantability and implied warranties for ﬁtness, are valid only

until Warranty Expiration Date as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties

express or implied. All products returned for warranty service require a Return Product Authorization Number (RPA#).

Contact Linear Returns at 1-855-546-3279 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and ﬁll an important need in portable wireless signaling.

However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices.

As such, they have limited transmitter power and therefore limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that

occur on or near their operating frequencies, regardless of code settings.

• Changes or modifications to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer,

and these facts should be communicated to the ultimate users.

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.linearcorp.com