liniLED Diffuse G4 User manual

LED strip manual
liniLED® Diuse G4
V231019
BEND RADIUS
R
150 mm
F
FROST
RESISTANT
RoHS IP68+
GLOW WIRE
850 °C
24
V DC
SEA WATER
RESISTANT
IP69K UV RESISTANT SWIMMING POOL
ENVIRONMENT
CRI
80+
IK08 CLEANING AGENTS
RESISTANT
SWIMMING POOL
SUBMERSIBLE
MAC
ADAM
2
S D C M
5
System

2
Manual | liniLED® Diuse
liniLED® Diuse G4
Technical notes 3
Technical specications 4
Product drawings 4
Maximum cable length 5
Product care and handling 6
Connectors 7
Installation 8
Power and connection diagram 10
Symbols 11

Manual | liniLED® Diuse 3
Read the instructions and safety precautions before installation, usage and storage of the products to secure safety of the user and reliability of the product.
- Hand over the instructions to the end user and those responsible for installation and usage.
- Triolight B.V. cannot be held responsible for improper handling, product installation, usage or storage.
Handling
- Handle with care.
- The product may not be modied or converted otherwise than prescribed.
- Products are transported in proper packaging. Products should remain packed until installation.
- Take ESD (Electrostatic Discharge) protection measures when handling liniLED® products.
- The products and their components may not be exposed to mechanical, static loads and other tension/compression other than from the product itself.
Installation
- Attention: The power has to be switched o the main power supply or the connection before installation. Not doing so may damage the product.
- Use a suitable LED power supply/driver: 24 V DC constant voltage. Do not drive the product on other voltages than described in their datasheet/products
specications.
- Installation has to be done by a certied professional with knowledge of electrical circuits or a specialised maintenance person known with valid directives.
- General and local construction-, safety- and installation regulations should be respected.
- Use only supplied parts, accessories and required tools as prescribed in the installation manual to guarantee a safe installation and use of the product.
- Products may solely be installed in the areas according to their prescribed IP-rating, IK-rating, temperature range and chemical resistances.
- The LED strip should be installed on an adequate cooling body for proper heat dissipation to ensure smooth operation and long lifetime.
- Do not fasten anything to the product. The same applies when hanging.
- Do not install the product in the following cases:
- Damage is visible on the product or its cables.
- The inside of the product is moistened or dirty.
- The product or its cables have been modied. This could lead to an electrical shock or a short circuit may occur.
- Children may not play unsupervised with electrical products as they cannot judge the dangers in dealing with electrical circuits correctly.
- Use proper mounting surfaces when installing in environments with large variations in temperature and operating lengths more than 2 metres. This should
absorb the stress of any dierence in expansion.
Operation and use
Solely use the product when it’s working correctly. If not, switch the power o immediately and ask an electrical specialist for advice in the following cases:
- Damage is visible on the product and/or the product does not function.
- The product is overheating and/or smoke or steam rises from the product.
- Crackling sounds are noticeable.
Repairs on the installation may only be performed by qualied electricians. Product repairs may solely be done by Triolight B.V.
Cleaning and maintenance
- Attention: Disconnect the power before maintenance and cleaning.
- Dust and dirt accumulated over time should be removed from the light emitting surface to assure optimal functioning of the product.
- Paints, solvents and corrosive cleaning chemicals may not contact and thus aect the product.
Environment and waste
- Exterior decorative lighting should only be used after sunset.
- This product may not be treated as household waste. Dispose of the material through the waste recycling of electrical and electronic equipment.
Warranty
This product comes with a 2 year warranty. Warranty void if:
- The installation guide has not been consulted (installation mistake).
- The installation is not done by a certied installer.
- Local rules and guidelines are not respected.
- The invoice cannot be shown and/or has been altered.
- Damage is caused by negligence, abnormal use or improper handling, use, maintenance and/or cleaning of the product.
Technical notes

4
Manual | liniLED® Diuse
Technical specications
Product drawings
12
18
33
LED strip length
3
18
10
4.5
18
18
33
LED strip length
3
18
10
4.5
liniLED® Top Diuse 12 & liniLED® Side Diuse
liniLED® Top Diuse 18
1. Colour temperature 3000K
2. LED strip length 1 m 2 m 5 m 10 m
3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC
4. Cable cross section 0.50 mm - 0.035 Ω/m 42.9 m 83.7 m 20.8 m 41.2 m 7.5 m 15.7 m 3.1 m 7.2 m
0.75 mm - 0.023 Ω/m 64.6 m 125.9 m 31.3 m 62.0 m 11.3 m 23.6 m 4.7 m 10.8 m
1.00 mm - 0.018 Ω/m 85.9 m 167.4 m 41.7 m 82.4 m 15.1 m 31.4 m 6.2 m 14.4 m
1.50 mm - 0.012 Ω/m 129.3 m 251.8 m 62.7 m 124.0 m 22.7 m 47.2 m 9.4 m 21.7 m
2.50 mm - 0.007 Ω/m 215.2 m 419.2 m 104.4 m 206.3 m 37.9 m 78.6 m 15.7 m 36.1 m
Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).
1= Select colour temperature.
2 = Select LED strip length.
3= Select output voltage.
4= Select cable cross section.
Result = Maximum cable length based
on the cable thickness and power supply
voltage.
Top Diffuse 12
3000 K
Top Diffuse 18
3000 K
Side Diffuse
3000 K
Product code [m] 12401 12411 12421
Power (24 V DC) 7.0 W/m 7.0 W/m 7.0 W/m
Power (25 V DC) 7.3 W/m 7.3 W/m 7.3 W/m
CCT12828 K 6370 K 2866 K
CRI >80 >80 >80
Luminous ux1169 lm/m 196 lm/m 101 lm/m
Luminous eciency124 lm/W 28 lm/W 14 lm/W
Spool length Max. 50m
Section length 50 mm
LED type 3014
Number of LEDs 6 per section/120 per metre
Max. connection length 10 m
Min. operating voltage 23 V DC
Max. operating voltage 25 V DC
Dimensions 12 x 18 mm 18 x 18 mm 12 x 18 mm
Dimmable PWM dimming, 24 V DC Common Anode
MacAdam Steps 3 steps
Weight 240 gram per metre 340 gram per metre 240 gram per metre
Expected lifetime L80/B10 > 60000 hrs @ Tc = 40°C
Ingress protection IP68+ > 50 m/IP69K
Storage temperature -30°C ... 55°C
Operating temperature2-30°C ... 55°C
Minimum bending radius 150 mm
1Typical calculated values are given, which due to tolerances in components and production process can vary up to 10%.
2Max. connection length between -30°C and -20°C is 7 metres.

Manual | liniLED® Diuse 5
1. Colour temperature 3000K
2. LED strip length 1 m 2 m 5 m 10 m
3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC
4. Cable cross section 0.50 mm - 0.035 Ω/m 42.9 m 83.7 m 20.8 m 41.2 m 7.5 m 15.7 m 3.1 m 7.2 m
0.75 mm - 0.023 Ω/m 64.6 m 125.9 m 31.3 m 62.0 m 11.3 m 23.6 m 4.7 m 10.8 m
1.00 mm - 0.018 Ω/m 85.9 m 167.4 m 41.7 m 82.4 m 15.1 m 31.4 m 6.2 m 14.4 m
1.50 mm - 0.012 Ω/m 129.3 m 251.8 m 62.7 m 124.0 m 22.7 m 47.2 m 9.4 m 21.7 m
2.50 mm - 0.007 Ω/m 215.2 m 419.2 m 104.4 m 206.3 m 37.9 m 78.6 m 15.7 m 36.1 m
Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).
1= Select colour temperature.
2 = Select LED strip length.
3= Select output voltage.
4= Select cable cross section.
Result = Maximum cable length based
on the cable thickness and power supply
voltage.
-+
1
2
3
4
Result
Top/Side Connector (1000 mm)
Maximum cable length

6
Manual | liniLED® Diuse
Product care and handling
Solely bend the liniLED® Top Diuse LED strip in up- and downward
direction when the light surface is facing upwards.
Do not bend the liniLED® Top Diuse LED strip in sideward
direction when the light surface is facing upwards.
Solely bend the liniLED® Side Diuse LED strip in sideward direction
when the light surface is facing upwards.
Do not bend the liniLED® Side Diuse LED strip in up- and
downward direction when the light surface is facing upwards.
150 mm
150 mm
The minimum bending radius of the liniLED® Diuse LED strips are
150 mm.
Do not twist, stretch or compress the liniLED® Diuse LED strips.
Side
Top/Side
Top
Side
Top/Side
Top

Manual | liniLED® Diuse 7
Connectors
The liniLED® Diuse LED strips come with a pre-assembled connector, available in dierent types. Extending LED strip can be achieved with the liniLED® Diuse
Extension Cord. Below is an overview of the available types with corresponding cable lengths and article numbers.
Product drawings (side view) Product code Cable length
IP20
Diuse Connector 90º Angle
11260 liniLED® Diuse Connector 90º Angle 12 1 m
11261 liniLED® Diuse Connector 90º Angle 12 5 m
11245 liniLED® Diuse Connector 90º Angle 18 1 m
11246 liniLED® Diuse Connector 90º Angle 18 5 m
1000 mm
5000 mm
1000 mm
5000 mm
IP20
Diuse Connector Straight
11270 liniLED® Diuse Connector Straight 12 1 m
11271 liniLED® Diuse Connector Straight 12 5 m
11250 liniLED® Diuse Connector Straight 18 5 m
11251 liniLED® Diuse Connector Straight 18 5 m
1000 mm
5000 mm
1000 mm
5000 mm
Diuse Extension Cord
11277 liniLED® Diuse Extension Cord Angle 12
11279 liniLED® Diuse Extension Cord Straight 12
11276 liniLED® Diuse Extension Cord Angle 18
11278 liniLED® Diuse Extension Cord Straight 18
300 mm
300 mm
300 mm
300 mm
IP67
IP67
Diuse Connector Male
11284 liniLED® Diuse Connector Angle Male 12
11286 liniLED® Diuse Connector Straight Male 12
11280 liniLED® Diuse Connector Angle Male 18
11282 liniLED® Diuse Connector Straight Male 18
300 mm
300 mm
300 mm
300 mm
IP67
IP67
Diuse Connector Female
11285 liniLED® Diuse Connector Angle Female 12
11287 liniLED® Diuse Connector Straight Female 12
11281 liniLED® Diuse Connector Angle Female 18
11283 liniLED® Diuse Connector Straight Female 18
300 mm
300 mm
300 mm
300 mm
IP67 Connection Cable Female
11274 liniLED® Connection Cable Female 5 m 5000 mm

8
Manual | liniLED® Diuse
Turn o the power. Make sure the wires are not under electric
current.
Unspool the LED strip on a horizontal surface.
Make sure the liniLED® Diuse LED strip and the U-Prole are
aligned.
Gently push the liniLED® Diuse LED strip into the U-Prole.
25 mm
Long lengths should be installed by two installers to prevent the
LED strip from twisting or bending. Keep in mind the minimum
bending radius of 150 mm.
Minimum bending radius of the cable is 25 mm.
Installation
3
5
1
4
6
2

Manual | liniLED® Diuse 9
Optional | Female connector front and isometric view, notice the
white marker on top (highlighted in orange).
Optional | Male connector front and isometric view, notice the
white marker on top (highlighted in orange).
FemaleMale
Male
Female
Optional | Align the white marker of the Female and Male
connector.
Optional | Snap the connector while keeping the white marker
aligned.
Turn the power ON.
9
11
7
10
8

10
Manual | liniLED® Diuse
Turn o the power before connecting the LED strip to the power.
liniLED® Control
(Optional)
L
N
Power Supply
24 V DC
-+
230 V AC
IP68+/IP69K
IP68+/IP69K
IP68+/IP69K
Connect the LED strip as indicated in the gure above.
Insert the power plug.
Power and connection diagram

Manual | liniLED® Diuse 11
Manufacturer’s declaration that the product meets the applicable EC directives.
Electrical appliance class III: this product is designed to be supplied from an extra-low voltage (≤ 60.0 V DC or ≤ 42.4 V AC).
This product can be applied in seawater and its environment. Elements in seawater will have no harmful eect on the product.
For chemical specications of these elements see the liniLED® material sheet. Verify the IP rating for proper use.
SEA
GLOW WIRE
850 °C
Passed glow wire test at 850 degrees Celsius. Global European regulations specify 650 degrees Celsius by default.
Product can be cleaned with normal cleaning agents.
CLEANING
This product is available on request and can be applied submerged in swimming pools and their environment. Disinfectants will have
no harmful eect on the product. For chemical specications of these elements see the liniLED® material sheet. Verify IP rating for proper use.
SWIMMING POOL
SUBMERSIBLE
MAC
ADAM
2
S D C M
White colour consistency up to 2 SDCM ellipse over an entire single strip length. LEDs used are single BIN 3 SDCM ellipse, but their careful
combination in a LED strip during the production process, results in a mixed light through a diusive material which is within a 2 SDCM ellipse
(probability >90%). Due to variability this is not legally binding. The guaranteed colour consistency can be found in the technical specications.
FSuitable for mounting on all surfaces and suitable to cover with insulating material.
Product is resistant against ultraviolet (UV) light or sunlight. Non-UV resistant products can degrade or discolour fast when exposed to UV light.
UV
Protected against impact energy of 5 joules.
IK08
This product can be applied inside swimming pool environments. Elements in the air will have no harmful eect on the product.
For chemical specications of these elements see the liniLED® material sheet. Verify IP rating for proper use.
SWIMMING POOL
ENVIRONMENT
RoHS
Restriction of Hazardous Substances (RoHS): product complies with the RoHS directive and each homogeneous material does not exceed
the limits for the materials mentioned under the RoHS directive (Pb, Hg, Cd, Cr6+, PBB and PBDE).
This product can be stored and used below 0 degrees Celsius. Verify the minimum storage and operating temperature in the datasheet or manual
for the lowest temperature allowed.
FROST
Operating voltage of 24 V DC.
24
V D
C
The CRI value of this product is 80 or higher.
CRI
80
+
This product needs to be disposed of separately from normal household waste so it can be recycled. Verify the IP rating for proper use.
5
System
System guarantee of 5 years when the complete system consist of liniLED® products with the 5 years system warranty logo.
Terms & conditions apply.
Symbols
Dust-tight, no ingress of dust. Protected against the eects of continuous immersion in water
(immersion in water at a maximum depth of 50 metres). Only in combination with the liniLED® Mirror Welded Connector.
IP68+
Dust- tight, no ingress of dust. Protected against close-range high pressure, high temperature spray downs.
Only in combination with the liniLED® Mirror welded connector.
IP69K

Disclaimer
The published information is checked to be as accurate as possible, however Triolight B.V. or any reseller of liniLED® cannot be held liable for any damages resulting
from misprints, errors, modications or outdated information. No legal rights can be derived from this document. Triolight B.V. reserves the right to modify the
information without informing the customers. Please check for the latest version on www.liniLED.com. This product should not be used in applications, devices or
systems where incorrect operation of the product may result in personal injury (includes emergency lighting) without written permission from the board of Triolight
B.V. If nevertheless used in such applications, devices or systems, Triolight B.V. cannot be held liable for any resulting injury. liniLED® is a registered trademark of
Triolight B.V.