Targus MIRALOGIC User manual
open size: 8.5"W x 11"H (
APS811 / 410-3882-001B)
Diecut Color: Pantone 424C
Introduction
Congratulations on your purchase of the Targus Miralogic Smart Power Strip.
Contents
(A) Miralogic Smart Power Strip
(B) User Guide
Features
• Stylish design for enterprise and ofce use.
• Capture power consumption data on each individual device plugged into the outlets.
• Deliver power consumpton analytics to the Miralogic Software Platform via the
Universal Smart Dock.
• Each outlet can be remotely managed (e.g. turned on / off) via the Miralogic
Software Platform.
Technical Specification
Number of AC outlets: 4
Maximum Current or Power: 120V, 8A or 960 watts
Input: 120VAC 60Hz 8A Max
Output: 120VAC 60Hz 8A Total (5A max per outlet)
MIRALOGIC SMART POWER STRIP
User Guide
APS811 / 410-3882-001B
(B)
(A)
Intended Use
This product is intended for enterprise use only. It is not intended for household use.
This product is intended to be used in dry indoor area only.
No liability will be accepted for damaged resulting from improper use or non-
compliance with these instructions.
Before First Use
Check for any transport damages.
Before connecting the product to the power source, check that the power supply
voltage corresponds with the input line voltage details shown on the rating label.
Using the Product
Connecting to a power source
Place the product nearby the power source and connect the power plug.
Power switch indicator (Red): The product is powered on.
Not Grounded (Red): The power is not grounded.
Power indicator (Green): The product is powered on.
Connected indicator (Blue): The product is successfully connected to the Miralogic
Software Platform via the Universal Smart Dock.
Circuit breaker
DO NOT OVERLOAD the product’s outlets. The product can accommodate a total AC
loading up to 8A (960W) (spread out over multiple outlets but single outlet can only
withstand a maximum of 5A). If the AC loading exceeds 960W, the built-in circuit
breaker (inside the power rocker switch) will trip and the outlets will stop providing
power immediately (red indicator goes off).
In case the circuit breaker trips, proceed as below:
1. Unplug all the connected equipment.
2. Press the power rocker switch and make sure the red indicator is on.
3. Connect all the equipment one by one. While doing so, do not exceed a total AC
loading of 960W.
Cleaning and Maintenance
To prevent electric shock, unplug before cleaning
During cleaning, the electrical parts of the product shall not be immersed into water
or other liquids. Never hold it under running water.
Cleaning
• Unplug the product from the wall AC outlet, wipe with a soft, slightly moist cloth.
• Dry the product after cleaning.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp
utensils to clean the product.
Maintenance
• Store in a cool and dry place away from children and pets.
• Avoid any vibrations and mechanical shocks.
open size: 8.5"W x 11"H (
APS811 / 410-3882-001B)
Diecut Color: Pantone 424C
Technical Support
For technical questions, please visit: http://www.targus.com/support.asp
Warranty
Targus warrants this product to be free from defects in materials and
workmanship for three years. If your Targus accessory is found to be defective
within that time, we will promptly repair or replace it. This warranty does not
cover accidental damage, wear and tear, or consequential or incidental loss.
Under no conditions is Targus liable for loss of, or damage to a computer; nor
loss of, or damage to, programs, records, or data; nor any consequential or
incidental damages, even if Targus has been informed of their possibility. This
warranty does not affect your statutory rights.
FCC statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
MIRALOGIC SMART SURGE PROTECTOR
User Guide
APS811 / 410-3882-001B
Features and specications are subject to change without notice. All trademarks and registered trademarks are the property of their respective owners.
All rights reserved. © 2020 Targus, 1211 North Miller Street, Anaheim, CA 92806.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure statements: Section 2.1091(d) (3) - Mobile devices (a minimum
separation distance may be required).
e.g. This device must be used in fixed locations and in such a way that a
separation distance of at least 20 centimeters is normally maintained between
the transmitter’s radiating structure(s) and the body of the user or nearby
persons.
IC statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditionssuivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
CAUTION
• USE INDOORS AND IN DRY LOCATIONS ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK.
• TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT PLUG INTO ANOTHER RELOCATABLE POWER TAP.
• INSPECT THOROUGHLY BEFORE EACH USE. DO NOT USE IF DAMAGED IN ANY WAY.
• ONLY INTENDED FOR USE WITH SMALL ELECTRICAL APPLIANCES SUCH AS NOTEBOOK COMPUTERS, MOBILE PHONES AND OTHER LOW VOLTAGE DEVICES.
• ENSURE THAT THE TOTAL CURRENT/POWER REQUIREMENT OF THE ATTACHED APPLIANCES DOES NOT EXCEED 120V, 8A OR 960 WATTS.
• SMART POWER STRIP MAY BE PERMANENTLY DAMAGED IF IT IS CONNECTED TO A POWER SOURCE GREATER THAN 120V AC.
