LINK Creative LKW300-21A3 User manual

LKW300-21A3
Quick Installation Guide

1. Packing List
Wireless router x1
Power adapter (DC) x1
ADSL splitter x 1
Quick installation guide x1
RJ45 Cable x1
RJ11 Cable x1
CD (user manual) x1
Warranty card X1
2. Installing Your Wireless Router
Step 1 Connect the ADSL interface of the device and the Modem interface of
the splitter through a telephone cable. Connect the phone to the Phone
interface of the splitter through a cable. Connect the incoming line to the
Line interface of the splitter.
The splitter has three interfaces:
Line: Connect to a wall phone jack (RJ-11 jack).
Modem: Connect to the ADSL jack of the device.
Phone: Connect to a telephone set.
Step 2 Connect the LAN interface of the device to the network card of the PC
through an Ethernet cable (MDI/MDIX).
Note:
Use the twisted-pair cables to connect with the hub or switch.
Step 3 Plug one end of the power adapter to the wall outlet and connect the
other end to the Power interface of the device.
The following figure shows the application diagram for the connection of the router,
PC, splitter and the telephone sets, when no telephone set is placed before the
splitter.

Caution:
The power specification is 12V DC, 800 mA. If the power adapter does not match the
specification, it may damage the device.
3. Front Panel
There are 9 LED indicators on the front panel of the wireless router. By observing
their status, you can judge whether the device runs normally.
The following table describes the status of LED indicators (from left to right) on the
front panel.
LED
indicator
Color Status Description
On The initialization of the device is successful.
Power Green Off The device is powered off.
On Connection between the device and the physical
layer of the office end is established.
Blinks
slowly No signal is being detected.
ADSL Green
Blinks The device is handshaking with the physical

LED
indicator
Color Status Description
quickly layer of the office end.
On
The Internet connection is normal in the routing
mode (for example, PPP dial-up is successful),
and no Internet data is being transmitted.
Blinks Internet data is being transmitted in the routing
mode.
Green
Off The device is in the bridge mode.
Internet
Red On
The Internet connection fails after successful
synchronization in the routing mode (for
example, PPP dial-up is failed).
On The LAN connection is normal and activated.
Blinks Data is being transmitted in the LAN or Internet
data is being transmitted in the bridge mode.
LAN
4/3/2/1 Green
Off The LAN interface is not connected.
On The WLAN connection has been activated.
Blinks Data is being transmitted in the WLAN.
WLAN Green
Off The WLAN connection is not activated.
Blinks WPS is enabled, and is waiting for client to
negotiate.
WPS Green
Off WPS is disabled.
4. Rear Panel
The following table describes the interfaces of the device.
Interface Description
WPS/WLAN
Press the button and hold it for less than 1 second to enable WLAN.
If WLAN is enabled, press the button for more than 3 seconds, to
initialize WPS negotiation.
ADSL RJ-11 interface, for connecting to the ADSL interface or a splitter
through a telephone cable.

Interface Description
LAN1/2/3/4 RJ-45 interface, for connecting to the Ethernet interface of a
computer or the Ethernet devices through an Ethernet cable.
Power Power interface, for connecting to the power adapter
Reset
This button is used to restore the factory default settings of router.
Keep the device powered on, and insert a needle into the hole for
more than 3 seconds, then release it. The device restores the factory
default settings of router.
Note:
The Reset button is in a small circular hole on the rear panel. If you want to
restore the default settings, please press the Reset button gently for more than
3seconds with a fine needle inserted into the hole and then release the button.
The system reboots and returns to the factory default settings.
5. Logging In to the Web Page
Step 1 Open the browser, and enter http://192.168.1.1/ in the IE address bar.
Step 2 Enter the correct user name and password in the login page.

Note:
The username and password of the super user are admin and admin.
The username and password of the common user are user and user.

Step 3 Click Login to log in to the Web page.
Step 4 Click Wizard and then you can follow the on-screen step-by-step
instructions to configure the wireless router. You may also configure the
router by referring to the User Manual included in the CD.