Linksys WPS54GU2 - Wireless-G PrintServer For USB 2.0 Print... Original operating instructions

A Division of Cisco Systems, Inc.
®
Model No.
Quick Installation
Model No.
Wireless
WPS54GU2
PrintServer for USB 2.0
Wireless-G
Package Contents
• Wireless-G PrintServer for USB 2.0
• Setup Wizard CD-ROM
•UserGuideonCD-ROM
• USB 2.0 Cable
•NetworkCable
• Power Supply
• Quick Installation
• Registration Card
1
2
Before starting the physical
installation, note the PrintServer’s
Default Name, which is located on
the bottom of the PrintServer.
APlug one end of the Ethernet
network cable into the
PrintServer ’s LAN port.
BConnect the other end to your
networked hub, switch, or
router.
CUse the USB cable to connect
your USB printer to the
PrintServer ’s USB port.
DUse the parallel printer cable
(not included) to connect your
parallel printer to the
PrintServer’s parallel port.
EPower on your printer.
FPlug the power adapter’s cord
into the PrintServer’s Power port.
GPlug the power adapter into
an electrical outlet.
Connect the PrintServer
router that automatically
assigns IP addresses, select
Automatically obtain an IP
address (DHCP) and click
Next. If you need to assign the
PrintServer a static IP address,
select Set IP configuration
manually, and enter the IP
Address, Subnet Mask, and
Gateway in the fields provided.
Then click Next.
GOn the Set PrintServer’s
Password screen, enter the
PrintServer’s default password,
admin, in the Current
Password field. Enter a new
password in the New Password
field, and enter it again in the
Verify Password field. Click
Next.
HOn the Wireless Settings
screen, enter your wireless
network’s SSID or name. If your
network is set to ad-hoc mode,
select the channel at which
the network broadcasts its
wireless signal. For the Network
Type setting, select
infrastructure if the PrintServer
will communicate using an
access point or wireless router.
Select Ad-Hoc if the PrintServer
will communicate directly with
wireless-equipped computers.
Click Next.
B
G
Configure the PrintServer
F
AInsert the Setup CD-ROM into
the computer’s CD-ROM drive.
The Setup Wizard should run
automatically. If it does not,
click Start and choose Run. In
the box that appears, enter
D:\setupWizard.exe (if “D” is
the letter of your CD-ROM
drive).
BOn the Welcome screen, click
Setup Wizard.
CThe Setup Wizard will search for
the PrintServer. After it has been
found, the screen in Figure C
will appear. If this is the first time
you have run the Setup Wizard,
make sure that List only new
(unconfigured) Print Servers is
selected and your PrintServer is
listed by its default server
name. If you have previously
configured the PrintServer,
select List all compatible Print
Servers. Click Next.
DOn the Password screen, enter
the default password, admin.
Click Enter.
EOn the Basic Settings screen,
you may change the Device
Name and Domain Name
settings if you want. Then click
Next.
FThe IP Settings screen will
appear. If your network uses a
H
GHz
2.4
802.11g
A
C
D
F
C
D
E

Linksys recommends that you set up
your printer and install your printer’s
driver before you install the
PrintServer’s driver.
AOn the Print Server Driver Setup
Welcome screen, click Next.
BOn the Choose Destination
Location screen, select the
location where the driver’s
folder will be installed. If you
want the folder to be installed
in a different location, click
Browse and select the
location. Click Next.
CThe Select Program Folder
screen will appear. An icon will
be added to the program
folder listed. If you want, you
may change the name of the
program folder. Click Next.
DAfter the driver is installed, the
Setup Complete screen will
appear. Make sure Configure
Print Driver now is selected.
Click Next to end the driver
installation and begin the driver
configuration.
A
IOn the Wireless Security
Settings screen, select a level
of WEP encryption, 64 Bit Keys
or 128 Bit Keys. Then enter a
Passphrase to automatically
generate a WEP key.
If you would like to enter your
WEP key manually, leave the
Passphrase field blank and
enter the WEP key on the next
screen.
Click Next.
JIf you used a Passphrase, then
a WEP key will appear on the
following screen. Otherwise,
enter your WEP key in the Key 1
field. Click Next.
KOn the Confirmation screen,
make sure your settings are
correct. Click Yes to save your
new settings.
LOn the Congratulations
screen, click User Install to
install the PrintServer’s driver.
3
F
Install and Configure the
JWhen you have finished
configuring the PrintServer’s
driver, click Close on the Printer
Port Setup screen.
Congratulations! The installation of
the PrintServer is complete.
EDouble-click the Print Driver
Setup icon on your desktop. If
you do not see the icon, click
Start, Programs, Print Server
Utility, and Print Driver Setup.
FRead the Information screen,
and click OK.
GOn the Printer Port Setup
screen, select a printer port to
add, and click Next.
HYou will be informed that the
PrintServer Port has been
added successfully. Click OK.
IThe Configure Printer Port
screen will appear. Your
installed printer(s) will appear in
the Existing Printers field. Select
the printer you want, and click
the Connect button to
associate the printer with your
selected printer port. To add
another printer, click Add New
Printer and follow the on-
screen instructions.
For additional information or troubleshooting
help, refer to the User Guide on the Setup CD-
ROM. You can also call or e-mail for further
support.
24-hour Technical Support
800-326-7114
(toll-free from US or Canada)
E-mail Support
[email protected]
Website
http://www.linksys.com or
http://support.linksys.com
RMA (Return Merchandise Authorization)
http://www.linksys.com/support
FTP Site
ftp://ftp.linksys.com
Sales Information
800-546-5797 (800-LINKSYS)
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2003
Cisco Systems, Inc. All rights reserved.
Model No.
WPS54GU2-QI-30826NC JL
PrintServer’s Driver
K
L
J
I
B
C
D
G
I
J
E
H