LION PX30A User manual

Rechargeable Solar Car Freezer
Thank you for choosing our Rechargeable Solar CarFridge Freezer
Please Read This Manual Carefully Before Using Your Unit.
User Manual
Model---- PX30A PX40A PX50A
Note: Please check if your product model includes a Portable
Power Station.PX30A PX40A PX50A

1
1. Features
• High efficiency DC compressor and conversion module with high reliability and
long life; compressor delay protection
• Quick cooling to -15°C (based on 25°C ambient temperature), lowest to -20°C
• Built-inPortable Power Station 15540mA/14.8V Lithium Ion 18650, 230Wh total.
• Portable Power Station recharging with solar panel (12v-30v), 12V/24VDC and
100-240VAC power adapter, allows charging with solar panel, car cigarette or
wall outlet
• Intelligent car battery protection system
• Portable design with trolley and wheels, removeable lid
• USB output +5VDC /2.1A for charging cell phone or iPad
• Fluoride-free insulation with good heat preservation performance and low
energy consumption, 45w DC/AC power only
• Wide range electronic temperature control, LCD display
2. SafetyInstructions
• Make sure the voltage is within the correct range for the socket and cable
being used. See technical data label on the side of the unit for voltage ranges.
• The unit must be placed in a dry and well-ventilated place far from heat
sources (such as stove, fuel), Place the unit in a well shaded area. Prevent
exposure to blazing summer sunlight as this will cause overheating in the
electronic compartment and product will be subject to failure. If compartment
reaches an unsafe temperature, the LCD display will read error ‘F8’ and
further instructions listed in section 6.FAQ of the user manual should be
followed. Protection of the compressor is important to keep the product
working at ideal conditions.
• Warning: Do not attempt or continue to operate your unit if electrical
compartment is wet. The installation of the DC power source in a boat should
be handled by qualified personnel.
• Your unit requires good ventilation; allow the following free space for air
circulation: back 200mm and side 100mm.

° It is recommended to operate the unit on a flat surface. Maximum operation
angle is 35°. During transportation, tilt less than 45° and handle carefully.
• No electrical devices should be placed inside the refrigerator, as they may be
damaged.
• The inner tank allows water filling, but do not pour water out by inverting the
unit. Keep the shells of the unit dry after rains. Do not submerge unit under
water.
• Although the units have been cleaned before leaving the factory, we strongly
recommend using a soft cloth dampened with warm water and a little neutral
detergent to clean it again, then wipe with a dry soft cloth. (Warning: Electrical
parts should be wiped by dry cloth only).
• Warning: Do not allow children to play games with the refrigerator such as
climbing or standing in the refrigerator. They could damage the refrigerator and
seriously injure themselves.
3. The Function and OperationSetting
Refrigerator Overall Design
Door LCD
Power
Compartment&Portable
Power Station
Cup
Holder
Solar Panel Input
DC Input

Temperature Temperature
Down UP Power Button “SET”Button
• Power On/Off: Press the Power Button to turn the unit on/off
• Temperature Setting: Can be adjusted by the “+" button up to 20 C (Max) and
down to -20 C (Max) by the “- “button; Default temperature is Celsius degree (c).
If you would like to change to degrees Fahrenheit (F), turn off the fridge, then
press and hold the SET button over 3 seconds. E1 should be displayed on screen
and begin flashing;
continue to press the SET button until E5 shows up, then press + or -, select
desired units: F or C.
•
The compressor will cool down the temperature from 10 C to -10 C in 20
mins. However, this reflects the change in temperature within the insulated
walls of the fridge/freezer. Allow an additional hour or more time,
depending on the food load, to reach a refrigerating temperature around 1-
6 degrees Celsius. To reach freezing temperatures with food or beverage
inside the unit will take approximately 8 hours. Therefore, if you want
frozen or chilling temperatures inside, we suggest you turn on the
compressor 10 hours ahead of time while keeping the temperature setting
at -15 % or lower
• Cooling Mode Control: Press the “ ” button to select control mode. Short
Presses will switch between MAX (Quick cooling mode) and ECO (Energy-saving
mode)
(tip: Max mode is recommended to begin initial cool down). After desired
temperature has been attained, it is recommended to switch to ECO mode to
conserve energy cooling mode.
USB

3
.
• Portable Power Station Protection: Selecting the H, M, L positions, you can
choose different levels for car Portable Power Station protection. When the unit
is on andworking, press the “ button over 3 seconds, then the LCD will
display as below:
o L: Low power protection 9.6V (factory default)
o M: Middle power 10.8V
o H: High power protection 11.3 V
When the unit is connected to the car, we suggest setting the car battery to “H”
level. L is suggested when the unit is powered with Portable Power Station or
other auxiliary backup Portable Power Station.
• USB Output: +5VDC /2.1A for cell phone, tablet, WIFI speaker, etc.

4
4. Power Supply andCharging
• Power Supply: The refrigerator is powered with 12V/24VDC power
• 100-240V AC (adapter included) or backup Lithium Portable Power
Station if there is no connection of DC/AC power. The connected DC/AC
power will operate the refrigerator directly and charge Portable Power
Station simultaneously.
• Portable Power Station Charging: The refrigerator allows three kinds of
charging methods. 12V/24VDC power, 100-240V AC with Adapter or solar
panel (12V-30V).
o DC/AC power connection: Car port and wall outlet cable included.
5.Portable Power Station Function

Model No:X230 Input
Portable Power Station :13000mAh/193Wh /14.8V
DCOutput1 ：12V/16V/20V/24V MAX96W
DCOutput2 ：12V~16.8V/MAX10A
USB1:QC3.0 /18W
USB2:+5V/4AMax
TYPE-C:PD60：5V/3A-9V/3A-12V/3A-15V/3A-20V/3A
LED: 2W
Input Voltage：12V/24V (MAX30V)
Charging Current:5A
Applied to Electronic Equipment
5.1 Portable Power Station Charging Method
DCOUT
POWER
DCoutput2
LED
LCD
DCIN
QC3.0
QC3.0
TYPE-C

5.11 Independent Charging（3Ways）
5.12 Charging In the Refrigerator（3Ways）

Additional Features

6
Solar panel (PV) charge connection: Solar charge cable included (20Ft Long)
Insert the solar charge cable into the refrigerator’s “PV" terminal
Max Solar input Voltage: 3 0 V
Max Solar input Current: 5A

7
Charge Way, 230Wh Lithium Time
AC Wall Charger (5A) 3 hours
DC Car Charger (5A) 3hours
Solar Panel Solar Charger (90W) About 3~4 hours
o Checking Charge Ctatus: When the refrigerator is powered ON and DC/AC
power is connected, the Portable Power Station on display screen will flash
to show charging. To charge the fridge/freezer Portable Power Station without
running the compressor, simply connect the adapters without powering ‘ON'
the unit. To view charging status please press and hold SET button “ "for
3 seconds. The unit’s Portable Power Station status and voltage will be
displayed. When the voltage reaches 16.8V and the Portable Power Station
icon stops flashing, the unit has been fully charged and wiring should be
disconnected to prevent internal component damage.

8
• AC Charging Management
O AC charging is always the first choice if AC power supply is available. Check
AC voltage range and use AC adapter to connect with AC power outlet.
o We suggest charging the refrigerator Portable Power Station to full using AC
adapter before you leave for a trip or outdoor activity.
O If the fridge has not been in use for a long time the Portable Power Station
may have over discharged and unit will not power on. Please use AC adapter
to charge unit to working mode. After unit has received up to 30% charge
other charging methods may be used.
•Car Port Charging Management
o Engine Turned-on: You can choose anyone of H, M or L mode (see car
battery in Chapter 5) and use car port power to operate the freezer.
Different cars may have different power output voltages. If the voltage
protection causes F1 error showed in the LCD, just set the Portable Power
Station protection from H to M or L. If the F1 error is still present, please
charge the unit with the adapter for few minutes and normal operation will
resume.
o Engine Turned-off: Charging using car battery: Most cars will stop power
supply if engine is stopped, but some cars will continue power supply even
when engine is stopped. You should adjust the battery protection to H,
otherwise, the power of your car battery may run out and it may not have
enough power to start car. You can also unplug the car port charger and run
the fridge/freezer using its internal Portable Power Station. If you don’t want
to use car battery it is recommended to disconnect the car charger from the
fridge and turn on Power Station .

9
• Solar Charging Management
o When charging by solar panel, turn on unit to verify charging is ineffect. Once
confirmed, unit may be turned off. Press and hold SET “ ”button over 3
seconds to show the Portable Power Station status and voltage.
OWhen using solar panel to charge the freezer use the extension cable and keep
the fridge in shade to avoid overheat and failure of refrigerator.
O When the refrigerator is powered ON and solar panel is connected to charge,
the Portable Power Station icon on display screen will flash to show charging
status.
6.Portable Power Station PowerOperation
• Backup Power: The Portable Power Station is back up power as UPS
power which keeps refrigerator operating while staying off grid.
• When charging the Portable Power Station or using Portable Power Station
power, please follow the instructions to turn on the Portable Power Station
switch.
• When not using the Portable Power Station power or Freezer for a long time,
please turn off the Portable Power Station output. /Reduce Portable Power
Station power drain)
• Discharge Time:
Discharge time
Refrigeration About 10 hrs
Freezing About 5 hrs
Note: Please charge fully before storage longer than 1 month.
7. FAQ
• The appliance is not working:
o Check that the Portable Power Station switch is turn on
o Check the power supply connection
o Check the plug and the socket connection.

10
o Ensure unit has been properly powered to ‘ON’ mode.
o Compressor may be in delay startprotection.

11
• The food inside is frozen: The setting temperature is too low.
• Hear water from the inside of fridge: It is normal, due to the flow of refrigerant.
• Display F1 code: Low power protection: setting the protection from H to M or L
• Display F2 code: Fan overload protection: turn off unit and restart the unit after
30 minutes
• Display F3 code: The compressor protection is activated: please turn off the unit
and restart the unit after 30 minutes.
• Display F5 code: Compressor controller module protection is activated: please
turn off the unit, keep it in a well-ventilated location and restart the unit after 30
minutes.
• Display F7/F8 code: Temperature sensor error: please move the unit in regular
temperature area for a while, then restart the unit.
If you still have the error, please contact us for support.
8.Food Storage
• Freezer (-20 °C-0°C):
o Meat should be cut and wrapped tightly, and then averagely placed inside. After
buying frozen food, put it in the freezer at frozen condition.
o Do not put the fresh food and frozen food together.
o Do not put the fruit and vegetable in the freezer to avoid freeze-drying.
o Do not put the glass container or other container with sealed liquid in freezer. Or
there is a possibility of explosion.
• Refrigerator (0°C -10°C):
o Eggs, butter, milk and bottled drink can be put in refrigerator.
o Fruit and vegetable should be put in bags for moisture retaining.
o Hot food should be cooled down before it’s placed to save power.
o Food must be packed into bags. Leaving space between packaged foods to
keep the circulation of cool air

12
9 . Defrosting
• After the refrigerator has been on for a period, frost could be seen on Inside
surfaces in the freezer, which reduces refrigerating effect and increases power
consumption. In this case, you need to defrost it.
• Unplug the refrigerator and open the doors, take the food in the refrigerator to a
cool place. Use defrosting shovel to remove ice and frost (also can just let the door
open, then ice and frost will be thawed by the raising temperature). Then use
dishtowel to wipe off the ice water. After that, place the food back to the refrigerator
and plug in.
Note: Do not use sharp metal tools to defrost which will damage the refrigerator.
10. Care and Cleaning
Unplug the refrigerator before cleaning!Turn off the portable power station
• Use soft cloth dampened with warm water to wipe the inner surfaces and external
appearance of therefrigerator.
• Use neutral detergent to clean the heavy stains, and dry with clean soft cloth.
• For long vacation or absences, remove food and unplug the refrigerator. Clean the
refrigerator and leave the doors open a little. Then place the refrigerator in
ventilated place.
• Do not use cleansers containing corrosive and deliquescent material (such as
scouring powder, bleach, soap powder, alkaline cleansers, benzene, gasoline, acid,
water, etc.) to clean the appearance panels, door gaskets and parts.
NOTE: Do not sprinkle water on the refrigerator during cleaning because that would
reduce the insulating property of electrical components and erode the metal parts.

13
11. The Following Situations areNormal
• The flow of refrigerant through the evaporator may create a boiling or gurgling
sound.
• In the rain and high humidity weather, moisture may form on the outside of
refrigerator or door gaskets. You can wipe damp surfaces with dry cloth.
• The temperature on the back panel may be high (particularly in summer) due to
the heat emission of the condenser.
• The temperature on external surfaces of the compressor may be high when the
compressor is working.
• The compressor may cause a high hum or pulsating sound when it is atstarting
or stopping.
• It’s normal to hear metal clanking noises from the compressor when the
refrigerator is bumped.
• There may be a slight smell coming from the rubber wheels. This is harmless for
health.
12. Technical Specification
MODEL PX30A/PX40A/PX50A
CLIMATIC CATEGORY T/ST/N/SN
PROTECTIVE CLASSIFICATION
OFELECTRIC SHOCRESISTANCE
III
RATED VOLTAGE DC (V) 12/24
FUSE 10A
TOTAL INPUT POWER 50W
RATED CURRENT FOR
DC(A)
4.2A/2.1A
REFRIGERANT (g) 30g/34g/36g/R134a
SIZE(mm) 628*409*403/628*409*513/628*409*583
N.W (kg) 13.4kg/14.9kg/15.4kg

14
13. Guidelines for Protection of the Environment
DISPOSAL: Do not dispose this product as unsorted municipal waste.
Separate collection of such waste isnecessary for special treatment and
disposal.
Meaning of crossed-out wheeled dustbin: Donot dispose ofelectrical
appliances as unsorted municipal waste. Use separate collection
facilities. Contact your local government forinformation regarding the collection
systems available. If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the groundwater and get into the food chain,
damaging your health and well-being.

15
Danger!
• Do not put the portable power pack into water or get it wet.
• Do not charge or store near fire or under extreme heat, especially when
leakage happens.
• Do not mix up positive electrode and negative electrode.
• Do not connect directly to AC power source.
• Do not transport or store with necklace or other metal material, this maycause
short circuit.
• Do not puncture or open, stamp, or impale.
• The terminals cannot be welded directly.
• Cannot be decomposed.
• Do not place in microwave ovens or pressured vessels.
• Do not combine with a one-shot Portable Power Station or Portable Power
Station with different capacity, model or type.
Do not use if abnormalities are noticed such as smoke, excessive heat, etc.
14.Pack list
Item Model Refrigerator DC power cord AC adaptor
Solar charge
cable
User's manual
15L
•1
•1
•1 •1
15. Warranty
• One-year warranty for unit. Please visit our website and make warranty
registration: https://www.acopower.com/productwarranty/register