Lippert Furrion FACB09HM User manual

9K BTU UNDER-BENCH AIR
CONDITIONER
MODEL: FACBHM
LIPPERT NO.: 
USER MANUAL
* Picture shown here is for reference only.
REV: 10.12.2022 CCD-0005748

CAUTION
FOR SAFE OPERATION, THIS UNIT MUST:
●This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
●If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
●The appliance have full disconnection switch in the fixed wiring in accordance with the wiring rules.
WARNING: Failure to do so can result in property damage, personal injury and or death.
CONTENTS
CONTENTS.............................................................................................................................................................................................................
GENERAL INFORMATION ................................................................................................................................................................................
Scope of the manual...................................................................................................................................................................................................................................2
Manufacturer and machine identification .......................................................................................................................................................................................2
Machine description....................................................................................................................................................................................................................................2
User tips .............................................................................................................................................................................................................................................................2
Description of the controls .....................................................................................................................................................................................................................2
Installing and changing the remote control batteries...............................................................................................................................................................5
Description of the wall pad...................................................................................................................................................................................................................... 5
Technical data ................................................................................................................................................................................................................................................6
INSTALLATION......................................................................................................................................................................................................
Packing, unpacking and handling........................................................................................................................................................................................................6
Choice of the place of installation .......................................................................................................................................................................................................7
Preparing the opening and fixing.........................................................................................................................................................................................................7
Installation......................................................................................................................................................................................................................................................... 8
Fitting the infrared wall pad..................................................................................................................................................................................................................... 9
Compartment opening and electrical hook-up ...........................................................................................................................................................................9
Air ducting.........................................................................................................................................................................................................................................................10
TROUBLESHOOTING, MAINTENANCE AND RECYCLING.................................................................................................................
Trouble, causes, remedies....................................................................................................................................................................................................................... 11
Maintenance....................................................................................................................................................................................................................................................12
Decommissioning and recycling..........................................................................................................................................................................................................12
English
Rev: 06-30-22 - 1 -
CCD-0005748

GENERAL INFORMATION
Scope of the manual
This manual has been drawn by the Manufacturer is an
integral part of the machine. The information it contains, if
observed, can guarantee correct use of the machine.
WARNING
This operation may be a source of danger.
Manufacturer and machine
identification
brand/ certificate
manufacturer information
mode/ technical
specifications
Machine description
This machine has been designed and built to be installed
on vehicles (motor homes, caravans, special vehicles, etc.)
in order to improve the internal temperature. When the
weather is hot it supplies cool and dehumidified air; When the
weather is cold it supplies hot air without however replacing
the vehicle’s original heating system. In both cases the air
temperature is adjustable.
User tips
NOTE: The machine performance can be improved by taking
some precautions.
●Improve the vehicle’s heat insulation by eliminating
openings and covering the glass surface with reflecting
curtains.
●Avoid frequently opening doors and windows when not
necessary
●Select the appropriate temperature and fan speed. Direct
the air vents suitably.
●In order to avoid machine malfunctioning and risks of
injury, take the following precautions:
●Do not obstruct the ventilation air inlet and outlet with
cloth, paper or any other items;
●Do not put your hands or any other items into the
openings;
●Do not spray water inside the machine;
●Keep flammable substances well away from the machine.
●Clean the air filter periodically.
Description of the controls
At the time of switching on,the system waits for a few minutes
before operating the compressor.
Press the “MODE” button to move between the possible
states (Auto, Cooling, Dry, Fan, and Heating), and wait two
seconds on the selected state for this to be confirmed by
the system with an audible warning (the buzzer is inside the
machine). Always point the remote control towards the to
send all the signals
Introduction of LCD icons
Icons Meaning Icons Meaning
Auto Airflow
direction
Cooling Fan speed
Dry Sleep
Fan Auto fan
Heating Temp
Light Clock
Electrical
Heat Timer
Lock
English
Rev: 06-30-22
- 2 - CCD-0005748

Remote control functions
9
10
7
8
11
12
13
14
1
2
4
5
6
3
FAN- FAN+
MODE
HEATER SLEEP
CLOCK TIMER
LOCK LIGHT
0 0
C / F
NO. BUTTON FUNCTION
1MODE Set up the air conditioner
operating mode
2FAN SPEED Set up the fan speed
3LOUVER SWING Adjust the airflow direction
4SLEEP
Automatically adjusting the
setting temperature according
the circadian rule.
5TIMER
Set up the time the air
conditioner starts
Set up the time the air
conditioner stops.
6LIGHT Switch on the light or UPI than
what unit has this function
7TEMP Set temperature unit to ℃or ℉
8UP Increase the temperature and
time
9ON/OFF Turn on or turn off the air
conditioner
10 FAN SPEED Set up the fan speed down
11 DOWN Decrease the temperature and
time
12 ELECTRICAL
HEAT
Switch on the electrical heat
in order to get enough heating
capacity in cold winter.
13 CLOCK Adjust the clock
14 LOCK Lock the remote control set
Heating mode
FAN- FAN+
MODE
HEATER SLEEP
CLOCK TIMER
LOCK LIGHT
0 0
C / F
1
Press the ON/OFF button “ ”
switch on the air conditioner, it will
run by memory mode.
2
Press the MODE button, set up
the mode to heat “ ” , the air
conditioner will run in heating.
3Press UP “ ” or DOWN “” button,
to adjust the setting up temperature.
4
Press the FAN SPEED button “FAN+
” or“FAN-”, set up the fan speed,
“” : Low speed,
“” : Middle speed,
“” : High speed,
“” : Auto speed.
For auto fan, the speed is chosen by
the difference of room temperature
and setting temperature.
5
Press the ON/OFF button “ ”
switch off the air conditioner. Next
time when this button is pressed,
the air conditioner will operates in
this mode by memory.
Cooling mode
FAN- FAN+
MODE
HEATER SLEEP
CLOCK T IMER
LOCK LIGHT
0 0
C / F
1
Press the ON/OFF button “ ”
switch on the air conditioner, it will
run by memory mode.
2
Press the MODE button, set up
the mode to cool “ ” , the air
conditioner will run in cooling.
3
Press UP “ ” or DOWN button
“”, to adjust the setting up
temperature.
4
Press the FAN SPEED button “FAN+
” or“FAN- ”, set up the fan speed,
“” : Low speed,
“” : Middle speed,
“” : High speed,
“” : Auto speed.
For auto fan, the speed is
chosen by the difference of
room temperature and setting
temperature.
5
Press the ON/OFF button “ ”
switch off the air conditioner. Next
time when this button is pressed,
the air conditioner will operates in
this mode by memory.
English
Rev: 06-30-22 - 3 -
CCD-0005748

Dry mode
FAN- FAN+
MODE
HEATER SLEEP
CLOCK T IMER
LOCK LIGHT
0 0
C / F
1
Press the ON/OFF button “ ”switch
on the air conditioner, it will run by
memory mode.
2
Press the MODE button, set up the
mode to dry “ ” , the air conditioner
will run in dehumidifying.
3Press UP “ ” or DOWN “ ” button,
to adjust the setting up temperature.
4
FAN SPEED button is “FAN+” or“FAN-
” disable, indoor fan speed always is
low in dry mode.
5
Press the ON/OFF button “ ”
switch off the air conditioner. Next
time when this button is pressed,
the air conditioner will operates in
this mode by memory.
Fan mode
FAN- FAN+
MODE
HEATER SLEEP
CLOCK T IMER
LOCK LIGHT
0 0
C / F
1
Press the ON/OFF button “ ”switch
on the air conditioner, it will run by
memory mode.
2
Press the MODE button, set up the
mode to fan “ ”, the air conditioner
will run in fan.
3Press UP “ ” or DOWN button “ ”,
to adjust the setting up temperature.
4
Press the FAN SPEED button “FAN+
” or“FAN- ”, set up the fan speed,
“” : Low speed,
“” : Middle speed,
“” : High speed,
“” : Auto speed.
For auto fan, the speed is chosen by
the difference of room temperature
and setting temperature.
Room temperature-setting
temperature
＞5℃high speed.
＞3℃middle speed.
＞1℃low speed.
5
Press the ON/OFF button “ ”
switch off the air conditioner. Next
time when this button is pressed,
the air conditioner will operates in
this mode by memory.
Sleep mode
FAN- FAN+
MODE
HEATER SLEEP
CLOCK T IMER
LOCK LI GHT
0 0
C / F
1
Press the ON/OFF button “ ”switch
on the air conditioner, it will run by
memory mode.
2
Press the MODE button, set up the
mode to cool “ ” / heat “ ” (heat
pump) / auto “ ”, the air conditioner
will run in setting mode.
3Press UP “ ” or DOWN button “ ”,
to adjust the setting up temperature.
4
Press the SLEEP button , this icon
will display on LCD, sleep function
is set up; press it again, cancel the
sleep function.
5If the sleep function is launched, the
fan speed is steady in low speed.
Auto mode
FAN- FAN+
MODE
HEATER SLEEP
CLOCK T IMER
LOCK LI GHT
0 0
C / F
1
Press the ON/OFF button “ ”switch
on the air conditioner, it will run by
memory mode.
2
Press the MODE button, set
up the mode to auto “ ” , the
air conditioner will run in auto
mode. (Reference to “emergency
operation”)
3
According to the difference of
room temperature and setting
temperature automatically choose
the running mode(cool, heat, fan).
The temperature setting button UP
“” or DOWN “ ”,are disable.
When room temperature≤20℃,
run with heat mode.
When 20℃＜room temperature
＜25℃, run with fan mode.
When room temperature≥25℃,
run with cool mode.
4
Press the FAN SPEED button “FAN+
” or“FAN- ”, set up the fan speed,
“” : Low speed,
“” : Middle speed,
“” : High speed,
“” : Auto speed.
For auto fan, the speed is chosen by
the difference of room temperature
and setting temperature.
5
Press the ON/OFF button “ ”
switch off the air conditioner. Next
time when this button is pressed,
the air conditioner will operates in
this mode by memory.
English
Rev: 06-30-22
- 4 - CCD-0005748

Timer off mode
FAN- FAN+
MODE
HEATER SLEEP
CLOCK T IMER
LOCK LI GHT
0 0
C / F
1
Press the ON/OFF button “ ”switch
on the air conditioner, it will run by
memory mode.
2Press the MODE button set up the
mode to which you want.
3Press UP “ ” or DOWN “ ”button,
to adjust the setting up temperature.
4
Press the FAN SPEED button “FAN+
” or“FAN- ”, set up the fan speed,
“” : Low speed,
“” : Middle speed,
“” : High speed,
“” : Auto speed.
For auto fan, the speed is chosen by
the difference of room temperature
and setting temperature.
5
Press the TIME OFF button “
” set up the time air conditioner
switch off. Press the button “
” each time, adjusting up 1 hour;
Press the button “ ” each time,
adjusting up 1 minute; When the
time is over, the air conditioner will
be switched off automatically. If
press this button again before the
air conditioner switch off, the timer
off setting will be cancelled.
Timer on function
FAN- FAN+
MODE
HEATER SLEEP
CLOCK T IMER
LOCK LI GHT
0 0
C / F
1The air conditioner is switched off.
2
Press the TIME ON button “
” set up the time which the air
conditioner switch on. Press the
button “ ” each time, adjusting
up 1 hour; Press the button “ ”
each time, adjusting up 1 minute.
Set up the operation MODE,
TEMPERATURE, FAN SPEED
etc., When the time is arrived, the air
conditioner will start automatically.
If the TIMER ON button is pressed
again, the TIMER ON setting will be
cancelled.
Electrical heat function
FAN- FAN+
MODE
HEATE R SLEEP
CLOCK TIMER
LOCK LI GHT
0 0
C / F
1
Press the ON/OFF button “ ”switch
on the air conditioner, it will run by
memory mode.
2
Press the MODE button, set up
the mode to heat “ ” , the air
conditioner will run in heating.
3Press UP “ ” or DOWN button “ ”,
to adjust the setting up temperature.
4
Press the FAN SPEED button “FAN+
” or“FAN- ”, set up the fan speed,
“” : Low speed,
“” : Middle speed,
“” : High speed,
“” : Auto speed.
For auto fan, the speed is chosen by
the difference of room temperature
and setting temperature.
5
Press the assistant ELECTRICAL
HEAT button “ ” the icon will
display on the LCD, starting the
assistant heat; press this button
again, stop the assistant heat.
6
Press the ON/OFF button “ ”
switch off the unit. Next time when
this button is pressed, the unit will
operates in this mode by memory.
Installing and changing the remote
control batteries
1. Take off the battery cover.
2. Insert the two batteries supplied (size AAA), paying
attention to their polarity.
3. Fit the battery cover back on.
4. Check the remote control works properly by pressing
the on button: if, on pressing the button, no icon appears
on the display then you need to re-install the batteries
checking their polarity. The machine is connected to the
power supply and ready for use.
Description of the wall pad
–Signal receiver
–Press the ON/OFF button to switch ON or OFF the air
conditioner, it will run in memory mode.
–Press the MODE button to select cooling or heating
English
Rev: 06-30-22 - 5 -
CCD-0005748

mode.
–Press the FAN button to select fan speed.
–Press the UP or DOWN button to select the desired
temperature.
1
2
3
4
5
wall pad
Technical data
296
30
398
86
86
14
734
296
30
398
86
86
14
734
Refrigerant type/quantity R410A / 500g
Cooling capacity(Btu/h) 9000
Heating capacity(Btu/h) 9000
Power Watts(Cooling) 925
Amps(Cooling) 4.2
Power Watts(Heating) 1250
Amps(Heating) 5.3
Breakaway current(A) 20(150ms)
Additional heating element(Watt) 500
Electricity supply 230 Vac/ 50 Hz
Protection class IP X5
Treated volume of air(max)(m³/h) 350
Max volume (recommended with
insulated walls)(m³)
30
Weight(kg) 27.8
E.E.R. 2.5
C.O.P. 2.6
Ventilation 3(Speed No.)
Outside operation temperature From -7℃to +43℃
INSTALLATION
Installation can be performed by persons with specific
technical knowledge. In addition to this requirement,installers
must have adequate working conditions in order to ensure
their safety and that others.
Packing, unpacking and handling
1. Observe the instructions given on the packing.
2. Lift the machine, checking it is sound.
Note: Lift it using the handlesor the belts on the base.
English
Rev: 06-30-22
- 6 - CCD-0005748

3. Transfer the machine to the place of installation in
conditions of safety.
Choice of the place of installation
To accomplish uniform climate control in a vehicle, the
machine must be installed as near the middle as possible, in a
housing or a similar device.
Position the machine so as to ensure easy access for
servicing and to facilitate disassembly and installation.
Place the assembly template in the compartment intended
for installation and check the space available for the
openings in the floor.
To minimize the transmission of noise and vibration during
operation, the machine must have a minimum clearance on
each side of 1⁄”(30 mm) from the walls and fittings,
The machine must be installed on the floor.
To make renewing the filter easier, keep a distance of
7⁄”(200 mm) between the front of the machine and the
walls of the compartment.
If fitting in external compartments (e.g., false bottoms), the air
to be treated must be drawn in from the vehicle’s passenger
compartment.
Drawing in outside air can significantly reduce the power of
the system.
Preparing the opening and fixing
55
734
398
16 191 51.8 135.4 270.9
206.4
2164630
Hole as an option
(to optimize the performance of the unit)
●To install the machine it is necessary to create openings
in the floor. The openings in the floor of the vehicle must
be accessible and, therefore, must not be covered by
parts of the chassis frame behind or the like.
●These openings must not be reached by splashes from
the wheels; fit a splash guard or something similar if
necessary.
●Take care to leave a gap of at least 1⁄”(30mm) between
the machine and the adjacent walls. Secure the machine
to the floor using the kit provided.
WARNING
The machine must preferably be installed level. Maximum
angle 10° to prevent condensation coming out. Before
making the holes, always check there are no cables, gas
pipes, parts of the chassis frame or the like underneath or
hidden. Seal the machined surfaces of the openings in the
floor with water-repellent products.
Fixing systems
Parts supplied for the a/c fixing
English
Rev: 06-30-22 - 7 -
CCD-0005748

(system 1)
(system 2)
(system 3)
FLOOR CUTS MAP
51.8
31.9
71.8
16
55
DRAIN HOLE
FIXING HOLE
(system 1)
FIXING HOLE
(system 1)
FIXING HOLE
(system 1)
FIXING HOLE
(system 1)
FRONT
FIXING HOLE
(system 2) FIXING HOLE (system 2)
FIXING HOLE
(system 2) FIXING HOLE (system 2)
FIXINGHOLE
(system3)
FIXINGHOLE
(system3)
FIXINGHOLE
(system3) FIXINGHOLE
(system3)
INLET
68 .2
191
2
135.4
184.4
OUTLET
HB9000
734
398
KEEP THIS DISTANCE BETWEEN THE UNIT AND THE SURROUNDING WALLS
10670.5
216
46
30
30
200
30
TO THE SIDE OF THE EXTERIOR WALL
1 2
3 4
(to optimize the performance of the unit)
Installation:
1.Open the side cover EPP,and have the
foam sticked around the air outlet.
2.Make a whole of the indicated size in
proper position.
3.Fix the grille.
4.Have the unit installed.
(Pls check when installation foam
thickness decided)
Hole as an option
1. Use n° 4 screws for the ale fixing
Pre-assembled
on the base
2. Use n° 8 screws, n° 4 brackets and n° 2 belts for the a/c
fixing
3. Use n° 4 screws and n° 4 washers for the a/c fixing
Hole as an option(to optimize the performance
of the unit)
Installation
1. Open the side cover EPP, and have the foam sticked
around the air inlet.
2. Make a whole of the indicated size in proper position.
3. Fix the grille.
4. Have the unit installed.
1
English
Rev: 06-30-22
- 8 - CCD-0005748

2
3
4
Fitting the infrared wall pad
1. On the top of machine, there is a pocket for wall pad,
remote control with battery and support, and extension
cable.
2. To fix wall pad on the wall, you need to make a diameter
⁄”(20mm)hole for cable to pass through.(refer to
drawing2).
3. Using 2 wooden screws to fix support to the wall, connect
extension cable to wall pad then put wall pad into its
support.
Cable
outlet slot
Compartment opening and electrical
hook-up
1. Make a hole in the compartment where the machine has
been installed to permit recirculation of the internal air;
Close this hole with a grille supplied that allows at least
300cmof air to pass through. Install the condensation
drain pipes provided, connect the receiver extension to
the machine and lastly power up by inserting its plug into
a socket outlet 220V - 50Hz.
2. Before switching on, make sure that the campsite column
and the extension used are able to withstand the power
input required by the machine(see technical data or
dataplate)
English
Rev: 06-30-22 - 9 -
CCD-0005748