Listen Technologies LR-3200 User manual

LR-3200
www.listentech.com
USER MANUAL
Basic DSP RF
Receiver (072 MHz)

2 LR-3200 Receiver Manual
Dear Valued Customer,
Thank you for choosing Listen! We are dedicated to providing you with
the highest quality products available, and take pride in delivering
outstanding performance to ensure you are completely satised.
We independently certify each of our products to the highest quality
standards and back them with a limited lifetime guarantee. We are
available to answer any questions you might have during installation or
in the operation of our products. At Listen, it’s all about you, should you
have any comments or suggestions we’re here to listen.
Here’s how to reach us:
+1.801.233.8992 +1.800.330.0891 North America
+1.801.233.8995 fax [email protected] www.listentech.com
Thank you and enjoy your listening experience!
Best regards,
Russell Gentner and the Listen Team
• In the few instances where repairs were needed, 99% of all clients indicated that they were
happy with repair turn-around-times and 85% of the time, clients were without their product for
less than 10 days!
• Overall client satisfaction of working with Listen was rated 4.8 out of 5.
• “Please continue with your excellent attitude toward customer satisfaction. You guys are great!”
• “I’ve never had such good service from any company. Keep up the good work!”
• “You stand behind your product wonderfully.”

TABLE OF CONTENTS
4 iDSP™ Receivers
5 LR-4200 Quick Reference
6 LR-4200 Specications
7 Safety Cautions!
7Hearing Safety
7Medical Device Safety
7Recycling
7Product Recycling Instructions
7Battery Recycling Instructions
8 Quick Setup and Operation Instructions
8Unpack Unit
8 Activate Battery
8Charge Battery
9 Connect Ear Phone
9 Using The Neck Loop Lanyard
9 Using The 3.5mm Headset Extension Cable
10 Turn the Unit On
10 Channel Select Mode
10 Adjust Volume
11 Battery & Belt Clip
11 Low Battery Indication
11 Belt Clip Installation/Removal
11 Accessing Battery Compartment
12 Reset to Factory Default Settings
13 Advanced Program Features an Listen’s UI
Conguration Software
13 Super Quiet Mode
13 Squelch
13 Basic Channels and Expanded Channels Modes
13 Channel Labels
13 Auto Power Mode
13 Unit ID
13 Brightness Control
14 Unit Information
14 Reset to Factory Defaults
14 Firmware Update
14 RF Reception Maximization Strategies
15 72 MHz Compatibility Chart
17 Troubleshooting LR-4200 Receivers
18 Compliance Notice and FCC Statement
19 Warranty
19 Contacting Listen

4 LR-3200 Receiver Manual
BASIC DSP™RECEIVERS
The LR LR-3200 is an Assistive Listening Receiver designed to be compact and simple to use. The unique
design of the receiver allows them to be worn as a necklace, using the belt clip or concealed in a pocket,
making this the most inconspicuous ALS receiver on the market.
Each receiver can be purchased with a Ear Phone/Neck Loop Lanyard that is designed to hold the receiver
like a necklace similar to the Blue Tooth™ transceivers used with many of the today’s hearing aids.
The Ear Phone/Neck Loop Lanyard can be used as the induction loop for those users who have T-coil
enabled hearing aids or cochlear implants, inducing the received audio directly into these T-coil enabled
devices. The Ear Phone/Neck Loop Lanyard also provides the connection to Listen’s Universal Ear Speaker,
Earphones and Headphones, incorporating a short connection cable that plugs directly into the Ear Phone/
Neck Loop Lanyards 3.5mm headset jack located 2/3 of the way up the lanyard. A second 3.5mm extension
cable provided with Listen’s universal earphones provides the length of cable required to place the receiver
in a pocket or using the belt clip.

LR-3200 Receiver Manual 5
LR-4200 QUICK REFERENCE
 PowerOn/O
Press and hold for 1 second to turn on. Press and hold for 3 seconds to turn o.
Up/Down Volume Control
Press momentarily to adjust the volume up/down or press and hold to ramp the volume.
Note: Press and hold both up and down buttons for 5 seconds to activate channel select,
use up and down to change the channel. Momentarily press the power button to save and exit.
Micro USB
USB charging, programming, rmware updates and inventory dispensing.
3.5 mm Output Jacks
Connect Listen Ear Phone/Neck Loop Lanyard for use with T coil hearing aids or with
Universal Ear Speaker or Headphone.
Belt Clip
To remove, remove screw and pull belt clip from unit. To install place belt clip in place
and insert screw.
Charging Contact
For use with Listen charging tray options.
LED
Indicates unit is on, low battery condition, and charging status.
Battery Protective Pull Tab
Remove clear plastic pull tab to activate internal battery connections.
Battery Door
Can be removed to access battery and product labeling information.
1
2
3
4
5
6
7
9
8
Up/down
Volume Control 2
Micro USB 3
5
6
9
8
3.5 mm Output Jacks
Belt Clip
Charging Contact
LED
Battery Protective Pull Tab
Battery Door
4
Power On/O 1
7

6 LR-3200 Receiver Manual
Product Specication: LR-3200-072
Audio
50 Hz - 15 kHz (±3 dB) / 50 Hz - 10 kHz (±3 dB)
SQ enabled 80 dB, SQ disabled 70 dB /
<1% total harmonic distortion (THD) at 80% deviation
Two (2) 3.5 mm (0.14 in.) connectors, unbalanced, 0 dBu
nominal output level, 50 mW maximum, impedance 32
ohm
Controls
Power, up/down volume
Press and hold up/down volume buttons for 5 seconds to
enter channel adjust, use up/down to select channel
Via software and USB port
Indicators LED Flashes when batteries are low or to indicate charging,
solid when fully charged
RF
72.025 - 75.975 MHz
Basic mode 3 wide band, Expanded mode 17 wide band
.6uV typical, 1 uV maximum for 12 dB sinad
± .005% stability 32 to 122 ºF (0 to 50 ºC)
Uses ear phone/neck loop lanyard and short ear phone
cable or standard earphone cable
Programmable in 20 steps, automatic on loss of RF signal
Power
Battery Type
Battery Life
Battery Charging Time
Power Supply
Lithium Ion
24 Hours of typical use
Fully charged in 2.5 Hours
Micro USB connector, 5 V, 500 mA
Physical
Dimensions (H x W x D)
Dimensions with Belt Clip
Unit Weight
Unit Weight with Batteries
Shipping Weight
Color
3.75 x 2.0 x 0.64 in. (9.6 x 5.0 x 1.7 cm)
3.75 x 2.0 x 0.80 in. (9.6 x 5.0 x 2.1 cm)
1.6 oz (45.4 g)
2.4 oz (68.1 g)
3.2 oz (90.8 g) with 16 oz (454 g) minimum
Flat Black
Environmental
Temperature - Operation
Temperature - Storage Relative
Humidity
14 to 104 ºF (-10 to 40 ºC)
(-)4 to 122 °F (-20 to 50 °C)
0 to 95% relative humidity, non-condensing
Compliance Standards FCC Part 15 Class B, Industry Canada, ICES-3 (B), RoHS
LR-3200 SPECIFICATIONS
System Frequency Response
System Signal to Noise Ratio
System Distortion
Output/s
User Controls
Set-up Controls
Programming
Frequency Range
Number of Channels
Sensitivity
Frequency Accuracy
Antenna Type
Squelch

LR-3200 Receiver Manual 7
LISTENTALK SAFETY CAUTIONS!
Hearing Safety
This product is designed to amplify audio to a high volume level which could potentially cause hearing
damage if used improperly. To protect your hearing make sure the volume is turned down before putting
on the ear speaker or headphones. Then adjust the volume up to the minimum setting require to hear
clearly. Do not allow children or other unauthorized individuals to have access to this product without
supervision.
Medical Device Safety
Before using this Listen product with an implantable or other medical device, consult your physician
or manufacturer of your implantable or other medical device. Always make sure you are using this
product in accordance with the safety guidelines established by your physician or the implantable
device manufacturer.
Recycling
Help Listen Technologies protect the environment! Please take the time to dispose of your
equipment properly.
Product Recycling Instructions
Please do NOT dispose of your Listen Technologies equipment in the household trash.
Please take the equipment to an electronics recycling center; OR, return the product
to the factory for proper disposal.
Battery Recycling Instructions
Please do NOT dispose of batteries in the household trash. Please take the batteries
to a retail or community collection point for recycling.

8 LR-3200 Receiver Manual
QUICK SETUP AND OPERATION INSTRUCTIONS:
1. Unpack Unit
Inspect the unit for physical damage. If damage is apparent, please contact Listen Technologies technical
support for assistance.
2. Activate Battery
Remove the clear plastic pull tab located at the bottom of the battery door, this will activate the internal
battery connections. Note: upon rst activation the battery will have a limited charge, we recommend
the unit be charged immediately.
3. Charge Battery
Fully charge the rechargeable Lithium Ion battery by connecting the unit to one of Listen Technologies
charging options.
a. LA-380 Intelligent 12-Unit Charging/Carrying Case
b. LA-381 Intelligent 12-Unit Charging Tray
c. LA-421 1-Port USB Charger (comes with cable)
d. LA-423 4-Port USB Charger (comes with 4 cables)
e. LA-422 USB to Micro USB cable (Connects receiver to any standard USB port)
When connected to a charging option the status LED next to the power button will begin to ash indicating
that the unit is charging. When the unit reaches 100% charged the status LED next to the power button will
stop ashing and will be solid.
Status LED: Flashes during
charging Solid when charge is
complete
Pull the tab to activate the
internal battery

LR-3200 Receiver Manual 9
4. Connect Earphone
Using The Earphone/Neck Loop yard:
Connect the Listen Intelligent ear phone/
neck loop lanyard to the two 3.5 mm output
jacks on the unit. Then connect the short
cable ear speaker or headphones to the
3.5mm output jack on the lanyard. The
lanyard neck loop is placed over the head
and worn as a necklace.
This is the preferred method of wearing the
receiver for best performance!
For T-coil compatible hearing aid use simply
disconnect the ear speaker or headset from
the ear phone/neck loop lanyard.
Using The 3.5mm Earphone Extension Cable: If the receiver is to be clipped to a belt, waistband or inside a
pocket a long extension cable is used. Connect the extension cable to the ear speaker, headset or earphones,
then connect the extension cable into one of the 3.5 mm output jacks on top of the receiver.

10 LR-3200 Receiver Manual
6. Channel Select Mode
The Listen receiver is pre-programmed to operate on channel E (72 MHz) from the factory. To receive audio,
both the transmitter and receiver(s) need to be set to the same channel. If not, the receiver channel needs to
reprogrammed to the channel being broadcast. To adjust the receiver to a dierent listening channel, press
and hold the volume up and down buttons simultaneously for 5 seconds. The front program (red) LED will
begin to ash and the current channel will be heard in the ear speaker.
Use the volume up or down button to scroll through the available channels. Once the desired channel is
located mometarily press the power button to save and exit the channel select mode or if no button is
pressed for 5 seconds then the selected channel will be saved and the unit will exit the channel select mode.
See page 14-15 for complete channel selection information.
Save/Exit: Press
power button to
save and exit
Program LED:
red
Channel Select Mode: Press and hold the up
and down button simultaneously for 5 seconds
Scroll Up/Down: Use the up or down button to
scroll through available channels
7. Adjust Volume
Adjust the listening volume to a comfortable listening level via the volume up/down buttons.
If the volume is adjusted while there is no audio present the unit will output a momentary tone each time the
button is pressed allowing the user to gauge and adjust the audio level to a comfortable listening level.
Note: To protect the users hearing, at power up the receiver will automatically reset to an adjustable default volume
level. Put on a headset and then adjust the volume to a comfortable listening level.
Power Button: Press and hold
for 1 second to turn on, press and
hold for 3 seconds to turn o
5. Turn the Unit On
Press and hold the Power Button for 1 second to
turn the receiver on. The LED will light solid.
To turn the receiver o, press and hold the
power button for 3 seconds
Volume Up/Down: Use the volume up
or down to raise/lower volume