Lithonia Lighting HFM Service manual

Installation Instructions
HFM Hazardous Location Floodlight
Class 1 Div 2
Groups A, B, C, D
Lithonia Lighting Outdoor
One Lithonia Way, Conyers, GA 30012
Phone: [phone] Fax: [phone]
www.lithonia.com
Part Number: RJ5210151 Rev B
Revision Date: 6/16/10
SAVE THESE INSTRUCTIONS
WARNING
To reduce the risk of death, injury or property damage from fire, electric shock, cuts,
abrasions, falling parts, and other hazards:
•Serviceoftheequipmentmustbeperformedbyqualifiedservicepersonnel.
•Installationandmaintenance must be performed byaperson familiar with the constructionand
operationofthis product and any hazards involved.Allapplicablecodes and ordinances must
befollowed.
•Readthisdocument before installing, servicing, ormaintaining this equipment or installinga
lamp.These instructions do not coverall installation, service, and maintenancesituations. If
your situation is not covered, or if you do not understand these instructions or additional
informationisrequired, contactLithoniaLighting or your local Lithonia LIghtingDistributor.
•Readandfollowallwarningsandinstructionsprovidedbythe lamp manufacturer.
WARNING
Before installing, servicing, or maintaining this equipment, follow these general precautions.
To reduce the risk of electrocution:
•Makesuretheequipment is properly grounded.
•Alwaysde-energizethe circuit and/or equipment before connecting to,disconnecting
from,orservicingtheequipment.
To reduce the risk of fire:
•Keep material away that can burn from hot lamp.
•Make sure lamps are correctly installed.
•Use supply conductors with a minimum installation temperature rating as specified on
equipment.
To reduce the risk of personal injury from cuts, abrasions, or falling parts:
•Wearglovestopreventcutsorabrasionsfromsharpedgeswhen removing from carton,
handlingandmaintainingthisequipment.
•Donot use abrasive materials, glasscleaners or other solventsonreflector or lens.
Thesesubstancesmay damage equipment and causepartstoeventually break and
fall.
•Do not install a damaged fixture.
CAUTION: Observelampmanufacturer’srecommendations and restrictions on lamp operation,
including but not limited to ballast type, burning position, replacement and cycling. Use only lamps that
complywithapplicableANSI standards.
NOTICE: If lamp is marked it contains mercury. Follow disposal laws. See www.lamprecycle.org
Lithonia Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for claims arising out of
improper or careless installation or handling of this product.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

Installation Instructions
HFM Hazardous Location Floodlight
Class 1 Div 2
Groups A, B, C, D
Lithonia Lighting Outdoor
One Lithonia Way, Conyers, GA 30012
Phone: [phone] Fax: [phone]
www.lithonia.com
Part Number: RJ5210151 Rev B
Revision Date: 6/16/10
©2001 Acuity Brands Lighting, Inc.
All Rights Reserved. Rev. 06/10
Delivery: Upon receipt of fixture and accessories (packed separately), thoroughly
inspect for any freight damage. All damage should be reported to the delivery
carrier. Compare the catalog description listed on the packing slip with the
fixture label on the inside of the housing to be sure you have received the
correct merchandise.
Lamp Installation: Loosen the 2 closing screws, hinge door assembly forward to access lamp compartment . Verify that the lamp source
and wattage corresponds with the fixture and ballast label. HID -Screw the lamp securely into the socket, back it out one or two turns,
and tighten securely again. This procedure properly seats the lamp in the socket. Close door using the standard closing screws.
Troubleshooting: If this fixture fails to operate properly, check to make sure: The proper lamp is installed correctly. • The fixture is
wired correctly. • The lamp is not faulty. • The fixture is grounded correctly. • The line voltage at the fixture is correct.
Multi-tap Ballast (TB): The multi-tap ballast will be prewired for 277V at the factory. First determine the correct line voltage. Then
select the corresponding fixture voltage lead, remove the crimped cap and connect to the supply voltage lead. The fixture lead marked
COM should be connected to the neutral supply lead for 120 or 277. For 208 or 240, connect the other incoming hot leg to the fixture lead
marked "COM". Be sure to cap off all unused fixture leads individually.
The standard fixture comes with a yoke mounting bracket which can easily be mounted to a variety of accessory mounting hardware.
1. Mount floodlight to desired mounting hardware.
2. Loosen the 2 captive screws in front housing and allow fixture to hinge open.
3. Loosen the two screws and remove optical assembly.
4. Secure appropriate conduit fitting (not provided) to fixture hub provided. Make wire connections. For multi-tap ballast, refer to
instructions below.
5. Replace optical assembly with two screws.
6. Lamp fixture per instructions below. Close front housing, and tighten the 2 captive screws.
OPERATING TEMPERATURE: The operating temperature
“T-Code”, listed for this luminaire is based on the following
bulb sizes. Use of any other than these may result in a
higher operating temperature.
Lamp Type Wattage Bulb Size Base
High Pressure Sodium 100 ED 17 Med
High Pressure Sodium 150 ED 17 Med
Metal Halide 150 ED 17 Med
Metal Halide 175 ED 17 Med