Little Giant VMC-1 User manual

REPLACEMENT PARTS LIST
ITEM
NO.
PART
NO. DESCRIPTION 560610
VMC-1
560620
VMC-1
1 153504 Tank 1 1
2 160920 Cover, Tank 1 1
3 925002 Grommet 1 1
4 160206 Screen, Chip 1 1
5 944202 Tubing, Vinyl, 1/2" I.D. x 6’ 1 1
6 170387 Valve, Flow Control 1 1
7 941007 Adaptor, 1/4" MNPT x 1/2" Hose 1 1
8 140509 Cap, Motor 1 1
9 140229 Stand/Volute Assembly 1 1
10 140309 Plate, Base 1 1
11 140412 Impeller 1 1
12 140942 Elbow Assembly 1 1
13 920006 Nut, #8-32 4 4
14 977206 Motor, 115V, 4’ Cord 1
14 977708 Motor, 230V, 6’ Cord 1
15 902436 Screw, 8-18 x 1/2" 4 4
540452 Replacement Pump Assy. 1
540454 Replacement Pump Assy. 1
©Copyright 2003 Little Giant Pump Company Form 994529–8/03:
• Assembly • Maintenance
• Safety • Repair Parts
CAUTION:
Read Safety Guidelines and Instructions Carefully.
INTRODUCTION
LITTLE GIANT MACHINE TOOL COOLANTS are carefully packaged, inspected and
tested to insure safe operation and delivery. When you receive the unit, examine it
carefully to determine that there are no broken or damaged parts that may have occurred
during shipment. If damage has occurred, make notation and then notify the firm from
which you purchased the unit. They will assist you in replacement or repair if required.
SAFETY GUIDELINES
1. Read all instructions and safety guidelines thoroughly. Failure to follow the guidelines
and instructions could result in serious bodily injury and/or property damage.
2. Do not pump flammable liquids such as gasoline or fuel oil with Little Giant pumps.
3. When working on the MACHINE TOOL COOLANT or pump, make sure that the power
is turned off. Make sure that the pump is disconnected from the power supply.
4. Make sure that the outlet for the pump is grounded.
MACHINE TOOL COOLANT PUMP ASSEMBLY
1. Unpack MACHINE TOOL COOLANT from the carton. Check the parts included with
the diagram in this instruction sheet for parts.
2. Assembly:
A. Feed tubing through grommeted discharge hole and attach it to pump discharge.
Attach flexible nozzle/valve assembly to the other end of flexible tubing.
B. Install motor/base assembly onto tank. Be sure chip collector is in place.
C. Your MACHINE TOOL COOLANT is now ready for operation. If any leakage
occurs, tighten the leaking connection.
MAINTENANCE
Never let sludge or excessive chips build up around pump. Periodically clear out the chip
collector and any sludge that may accumulate in the bottom of the tank. The chip
collector is designed to filter out abrasive media that may damage the pump.
Never operate MACHINE TOOL COOLANT without chip collector.
Do not use cutting oils with viscosities greater than the pump can handle.
Little Giant Pump Company
P. O. Box 12010
Oklahoma City, OK 73157-2010
[phone] •Fax: [phone]
Little Pump Company
GIANT
Machine Tool Coolant
Owner’s Manual
VMC-1
PumpAgents.com - Click here for Pricing/Ordering PumpAgents.com - Click here for Pricing/Ordering

LIMITED LIMITED
WARRANTY LITTLE GIANT WARRANTY STATEMENT WARRANTY
Your Little Giant product is guaranteed to be in perfect condition when it leaves our Factory. It is warranted against defective
materials and workmanship for a period of 12 months (90 day warranty on Models 1-AA-OM, GKPK, PP-1, PPS-1, PP-12, PPS-12, and
PP-230) from date of purchase by the user. No warranty on brush wear in Model 35-OM and impeller or cam in Models PP-1, PP-12,
and PP-230.
Any product that should fail for either of the above two reasons and is still within the warranty period will be repaired or replaced at
the option of Little Giant as the sole remedy of buyer. For our customers in the CONTINENTAL UNITED STATES: Please return the
defective unit, postage paid, to the factory at 3810 North Tulsa, Oklahoma City, OK 73112. All defective product returned under
warranty will be fully inspected to determine the cause of failure before warranty is approved.
For our customers located elsewhere; it is not economical, due to duties and freight, to return the pump to the factory for
inspection. Please return the defective unit to any authorized distributor or dealer with a brief written explanation of the problem. If
there are no apparent signs of customer abuse, unit will be repaired or replaced. If dispute arises over replacement of the pump, the
distributor or dealer is to segregate such items and hold for inspection by a representative of Little Giant Pump Company or notify
factory with details of the problem for factory disposition and settlement of warranty claim.
DISCLAIMER: THE FOREGOING WARRANTY IS AN EXCLUSIVE WARRANTY IN LIEU OF ANY OTHER EXPRESS
WARRANTIES. ANY IMPLIED WARRANTIES (INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) TO THE EXTENT EITHER APPLIES TO A PUMP SHALL BE
LIMITED IN DURATION TO THE PERIODS OF THE EXPRESS WARRANTIES GIVEN ABOVE.
Warranty will be VOID if any of the following conditions are found:
1. Sealed motor housing opened.
2. Product connected to voltage other than indicated on nameplate.
3. Cord cut off to a length less than three feet.
4. Pump allowed to operate dry (fluid supply cut off).
5. Pump used to circulate anything other than fresh water, light oils, or other mild liquids at approximately room temperature.
6. Product abuse by customer.
Any oral statements about the product made by the seller, the manufacturer, the representatives or any other parties, do not
constitute warranties, shall not be relied upon by the user and are not part of the contract for sale. Seller’s and manufacturer’s only
obligation, and buyer’s only remedy, shall be the replacement and/or repair by the manufacturer of the product as described above.
NEITHER SELLER NOR THE MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR
CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS,
LOST SALES, INJURY TO PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS), ARISING OUT OF
THE USE OR THE INABILITY TO USE THE PRODUCT AND THE USER AGREES THAT NO OTHER REMEDY SHALL BE AVAILABLE
TO IT. Before using, the user shall determine the suitability of the product for the intended use, and user assumes all risk and liability
whatsoever in connection therewith.
Some states and countries do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state and country to country.
The National Electric Code (in the USA) and similar codes in other countries require a Ground Fault Circuit Interrupter (GFCI) to be
installed in the branch circuit supplying fountain equipment rated above 15 volts. 115 volt GFCI’s (with various cord lengths) are in
stock, and we recommend each pump be used with a GFCI.
KEEP THIS FOLDER
File this for safe keeping. It may be valuable to you for service under the terms of the
warranty.
Date of Purchase _____________________________________________________________
Name of Dealer ______________________________________________________________
Date Code___________________________________________________________________
For Parts or Repair, please contact 1.888.572.9933
For Technical Assistance, please contact 1.888.956.0000
PumpAgents.com - Click here for Pricing/Ordering PumpAgents.com - Click here for Pricing/Ordering