Little Seeds 5347344COM User manual

B345347344COM0

2
5347344COM
Storage Bench
Keep this Assembly Manual for future reference.
Two adults
recommended
for assembly
Do NOT return this product.
For missing or broken parts
- Visit littleseedskids.com
- Call 1-800-489-3351
Follow little seeds on
This product is not intended for commercial use.
Las traducciones en español se encuentran al final
de este manual.
Vous trouverez les traductions en français à la fin
de ce manuel.
WARNING
- Unit can tip over causing severe injury or death.
- Anchor unit to stud in wall (if instructed to).
- Do Not allow children to climb on unit.
- Put heavy items on lower shelves or drawers.

3
littleseedskids.com
Tube
You
Call us!
1-800-489-3351
Monday-Friday
9am - 5pm CST
- Open your item in the area you plan to keep it for less heavy lifting
- Identify, sort and count the parts before attempting assembly
- Compression dowels are tapped in with a hammer
- Slides are labeled with a R (right) and L (left) for proper placement
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge
- Use all the nails provided for the back panel and spread them out equally
- Back panel must be used to make sure your unit is sturdy
- Do NOT use harsh chemicals or abrasive cleaners on this item
- Never push, pull, or drag your furniture
Helpful Hints
Visit littleseedskids.com to view the
limited warranty valid in the U.S. and Canada.
Assembly Tips
Contact our friendly customer service team first for help.
Do NOT return this product!
PEOPLE NEEDED FOR ASSEMBLY: 1-2
ESTIMATED ASSEMBLY TIME: 1 HOUR

4
littleseedskids.com
Before You Start
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process.
P
P
P
P
1
34
2
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.
P

5
littleseedskids.com
Board Identification
Left Panel
35347344010
I
H
G
K
J
F
E
D
C
BA
This piece is paper board construction.
It is not made from wood but is
required for the assembly of
your unit.
x2
Divider
35347344030
Right Panel
35347344020
Upper Divider
35347344040
Top
35347344050
Bottom
35347344060
Shelf
35347344070
Left Front Molding
35347344080
Right Front Molding
35347344090
x2
Rear Molding
35347344100
Back Panel
K534734400

6
littleseedskids.com
Board Identification
A
B
C
D
E
F
G
K
J
I
H
C
This piece is paper board
construction. It is not made from
wood but is required for the
assembly of your unit.

7
littleseedskids.com
Parts List
Not Actual Size
Actual Size
x18
cam bolt
A22610
x18
cam lock
A22620
x18
wood dowel
A21660
x6
confirmat screw
A23030
x12
#8 x 1-1/8" fl at head
A12950
x26
nail
A21110
x3
storage bin
A91580
x2
plastic foot
A43490
x4
decorative angle bracket
A53570
x2
decorative corner brackt
A53580
1
2
3
4
5
6
7
8
910

8
littleseedskids.com
Step 1
5
(x6)
#8 x 1-1/8" fl at head
5
A
H
H
J
J
A
Be sure all edges are flush with each other.
5
5
5
5
5
end
view
Note: Screw through panel and
into groove in molding.
Note: Finished edge of left panel (A) will
sit into left front molding (H) as shown.
A
H

9
littleseedskids.com
Step 2
Proper orientation of CAM LOCK
Tip
Assembly
Quick
1
2
3
x4
cam bolt
x2
cam lock
x2
wood dowel
1
2
3
J
A
H
1
1
1
2
3

10
littleseedskids.com
Step 3
5
5
Be sure all edges are flush with each other.
end
view
Note: Screw through panel and
into groove in molding.
Note: Finished edge of right panel (B) will
sit into left front molding (I) as shown.
(x6)
#8 x 1-1/8" fl at head
I
B
J
5
5
5
5
5
B
B
I
I
J

11
littleseedskids.com
Step 4
Proper orientation of CAM LOCK
Tip
Assembly
Quick
3
2
1
1
2
3
x4
cam bolt
x2
cam lock
x2
wood dowel
B
J
I
2
1
1
1
3

12
littleseedskids.com
Step 5
2
3
x4
cam lock
x4
wood dowel
8
x2
wood dowel
2
3
2
2
2
3
3
3
8
8
Tap each plastic foot (8) lightly with a hammer to fully seat onto the bottom (F).
F
Proper orientation of CAM LOCK
Tip
Assembly
Quick

13
littleseedskids.com
Step 6
Proper orientation of CAM LOCK
Tip
Assembly
Quick
3
2
1
2
3
1
x4
cam bolt
x4
cam lock
x4
wood dowel
2
2
2
1
1
1
3
3
G
3

14
littleseedskids.com
Step 7
3
2
2
3
x6
cam lock
x6
wood dowel
D
C
x2
Proper orientation of CAM LOCK
Tip
Assembly
Quick
2
2
2
3
3
3

15
littleseedskids.com
Step 8
4
UNLOCKLOCK
x2
confirmat screw
G
C
C
D
4
All finished edges to face up.

16
littleseedskids.com
Step 9
4
4
x4
confirmat screw
C
C
F
All finished edges to face up.
4
4
4

17
littleseedskids.com
Step 10
UNLOCKLOCK
F
G
A
B
All finished edges to face up.

18
littleseedskids.com
Step 11
1
x6
cam bolt
1
1
1
1
1
1
E

19
littleseedskids.com
Step 12
UNLOCKLOCK
All finished edges to face up.
A
B
E
D

20
littleseedskids.com
Step 13
IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT AND MUST BE INSTALLED PROPERLY.
Carefully turn the unit over on its front side. Make sure the unit is square. Position the back
panel as shown. Align the back panel equally with all outside edges and nail straight through
into the back edges as shown.
Make sure edge of back panel is
flush with edge of bottom.
Assure that the unit is square.
Distance from corner to corner
must be equal.
6
x26
nail
6
"raw surface shown"
K