Little Tikes 630293 User manual

ASSEMBLY INSTRUCTIONS
Hide & Seek™ Climber & Swing
XIM630293 - 12/20
1
Adult assembly required. Approx. assembly time: 30 min.
Look for video of assembly at
littletikes.com/videoinstructions
#630293
1-4
years

2
WARNINGS!
• Adult Assembly Required
• Keep these instructions for future reference.
• Prior to assembly, this package contains small parts: hardware which is a choking hazard
and may contain sharp edges and sharp points. Keep away from children until assembled.
• To prevent serious injury, children must not use the equipment until properly installed.
• Falls onto hard surfaces can result in head or other serious injuries. Never place on concrete,
asphalt, wood, packed earth, grass or other hard surfaces. Carpet over hard oors may not
prevent injury. Always use protective surfacing on the ground under and surrounding the
playground equipment according to the enclosed “Consumer Information Sheet for Play-
ground Surfacing Materials.” Maximum fall height protection up to 3 feet (.91m) required.
• Adult supervision required. Do not leave children unattended.
• This product is intended for use by children ages 1 - 4 years.
• Maximum weight per child: 45 lbs. (20.4 kg). Limit 2 children on climber. Limit 1 child on swing.
• Shoes must be worn at all times.
• This product is intended for outdoor domestic family use only.
• Observing the following statements and warnings reduces the likelihood of serious or fatal injury.
• Place this product on level ground and at least 6’ (2 m) away from any object. Objects to be
avoided include, but are not limited to, fences, buildings, overhead branches, laundry lines or
electrical wires.
• It is recommended that the orientation of the assembled product be such that direct sunlight
is minimized on surfaces intended for standing or sitting.
• Instruct children on proper use of this product, only after properly placed, and not in a manner
other than intended.
Thank you for choosing the Little Tikes©Hide & Seek™ Climber & Swing .
We strive to provide a durable, easy-to-assemble toy thats made to last,
giving your child years of imaginative, engaging fun!
• Read through all the instructions rst.
• Clear a at surface to lay out all the materials so everything is close at hand.
• You will need a Flat head screwdriver, Phillips head screwdriver , 1/2” (1.27cm)
and socket wrench to assemble the Hide & Seek™ Climber & Swing.
• The parts are listed below - each part is identied with a letter in RED for easy reference.
• Illustrations are for reference only. Styles may vary from actual contents.
• If you have any questions, we’re here to help. Give our customer service team a
call at 1-800- 321-0183.
Really important information you should know!

3
• Instruct children to remove their bike or other sports helmet before playing on this product.
• Dress children appropriately: do not allow children to wear loose-tting clothing including
ponchos, scarves and garments with drawstrings. Well-tting shoes must be worn at all times.
• Instruct children on proper swing use for their safety:
• Do not twist chains. Do not swing empty seats.
• Children should keep hands free of objects, inside of swing, and hold onto the ropes.
• Do not get o the swing while it is in motion.
• Do not walk too close to, in front of, behind, or between moving items.
• Always wear well-tting shoes while swinging.
• Always sit with full weight in the center of the seat.
• Do not twist chains or ropes or loop them over the top support bar since this may reduce
their strength.
• Do not use the equipment in a manner other than intended.
• Do not allow children to climb on product when product is wet.
• Instruct children not to attach items to the product that are not specically designed for
use with the product such as, but not limited to, jump ropes, clotheslines, pet leashes,
cables and chains, as they may cause a strangulation hazard.
MAINTENANCE
Failure to perform periodic checks could cause this product to overturn or cause a fall.
The following checks should be performed at the beginning of each season and twice monthly
during the usage period:
• Reinstall any plastic parts, such as swing seats or any other items that were removed for the
cold season.
• Tighten all hardware.
• Lubricate all metallic moving parts at the beginning of the play season and twice per month
during the play season.
• Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose,
cracked, or missing.
• Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or
other deterioration. Replace if any of these conditions exist.
• Check metal parts for rust. If found, sand and repaint using a nonlead-based paint meeting
the requirements of 16 CFR 1303.
• Rake and check depth of loose ll protective surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as necessary.
• Take this product indoors or do not use when temperatures fall below 0°F/-18°C.
• Owners shall be responsible for maintaining the legibility of the warning labels.
DISPOSAL
Disassemble and dispose of equipment in such a manner that no hazardous conditions such as,
but not limited to, small parts and sharp edges exist at the time equipment is discarded.

4
(2) 1" (2.54cm)
Shown actual size
Wall Nut (8) Nuts (2)
Washer (2)
DD
EE
AA
(2) 11/2" (3.81 cm)
A Few Things Before You Start!
BEFORE you begin assembly, make sure
you have all the parts listed below.
Some packages of hardware may have extras pieces.
!
Questions? We’re here to help.
Little Tikes customer service team at 1-800- 321-0183.
!
2
(2) 3¼" (8.25cm) Eye bolt
Tools required (not included)
Hardware Guide
Tools included
1/2" (1.27 cm) socket
Clé à douille de 1,27 cm
Llave tubular de 1,27 cm
Platform nut (2)
Header cap (2)
BB
CC

5
Treetop (1)
Wall (1)
Trunk (1)
A
C
B
Wall (1)
D
Platform (1) Rock wall (1) Slide (1)
EFG
Swing (1)
H
Swing arms (1)
I
Swing support (1)
J

6
1
Ready or not, here we go!
Place the platform (part E) onto the rock wall (part F),
and secure (2) platform nuts (part BB).
x2
BB
E
F
2
Get the walls up!
First line up wall (part D) to the assembled platform.
Then align wall (part C).
Secure using (3) wall nuts (partAA) for each wall.
x6
AA
DC

7
3
Attach the slide
First connect one side of the slide (part G)
to the assembled platform, then click in the other side.
G
Click
2
1
4
1,2,3 and you have a tree!
First slide treetop onto the trunk.
Then secure using (2) 1½ (3.81cm) screws.
x2
1½" (3.81 cm)

8
5
Let’s get swinging
Loop one swing arm (part H) through the hole
on the swing (part H). Repeat on the other side.
H
I
Ix2
Flip the swing over before
securing the screws.
x2
1" (2.54cm)
Secure using (2)
1”(2.54cm) screws.

9
5a
Let’s get swinging...cont.
Attach one eye bolt 3 ¼" (8.25cm) to each side of swing arms.
3¼" (8.25cm)
x2
Attach swing arms (eye bolts rst) through the
holes in the swing support (part J).
J

5b
Let’s get swinging...cont.
Slide (1) washer (DD) then (1) nut (EE) onto the eye hook.
Tighten into the swing support (J) using the socket wrench.
J
DD washer
EE Nut
Push in (2) header caps (CC) on top
of the nut and washer.
Turn locking nut 4-5
times to tighten.
DO NOT over tighten.
x2
CC
10