Little Tikes 650666M User manual

ASSEMBLY INSTRUCTIONS
Flowin’ Fun Water Table™
XIM650666-R1 - 12/20
1
Adult assembly required. Approx. assembly time: 30 min.
Look for video of assembly at
littletikes.com/videoinstructions
#650666M
2+
years

2
WARNINGS!
• Adult Assembly Required
• Keep these instructions for future reference.
• Prior to assembly, this package contains small parts: hardware which is a choking hazard
and may contain sharp edges and sharp points. Keep away from children until assembled.
• Adult supervision required. Do not leave children unattended.
• Use this product on a rm, level surface and avoid using near swimming pools, on or near
steps, hills or inclines.
• This product is intended for outdoor domestic family use only.
• This product is intended for use by children ages 2 years and up.
• Do not allow children to sit, stand, play or climb on the top surface. Failure to do so may
cause the product to become unstable.
• Intended for use with the supplied accessories only.
• Never ll with anything except clean tap water. Use of other liquids may be harmful
or damage the unit. Never ll with sand or dirt.
• Do not store or leave water in product when not in use.
DISPOSAL
Disassemble and dispose of equipment in such a manner that no hazardous conditions
such as, but not limited to, small parts and sharp edges exist at the time equipment is discarded.
Thank you for choosing the Little Tikes©Flowin’ Fun Water Table™ .
We strive to provide a durable, easy-to-assemble toy thats made to last,
giving your child years of imaginative, engaging fun!
• Read through all the instructions rst.
• Clear a at surface to lay out all the materials so everything is close at hand.
• You will need a pair of pliers (not included) to assemble the Flowin” Fun Water Table™.
- When installing screws, be sure screws are tightened snugly, but do NOT OVER-TIGHTEN.
• The parts are listed below - each part is identied with a letter in RED for easy reference.
• Illustrations are for reference only. Styles may vary from actual contents.
• If you have any questions, we’re here to help. Give our customer service team a
call at 1-800- 321-0183.
Really important information you should know!
Tools Required (not included)

3
Center
Cap (1)
F
Center
Funnel (1)
E
A Few Things Before You Start!
BEFORE you begin assembly, make sure
you have all the parts listed below.
Some packages of hardware may have extras pieces.
!
Questions? We’re here to help.
Little Tikes customer service team at 1-800-321-0183.
!
Illustrations are for reference only. Styles may vary from actual contents.
Table Top (1)
A
Legs (3)
B
Center Column (3)
G
Center Connector
Assembly (1)
H
Spray Assembly (1)
I
Elbow (1)
O
Pop up
Base (1)
J
Pop up
Assembly (1)
K
Spinners (3)
L
Sprinkler Stick (1)
M
Center Bubble
Tube (1)
N
Hose (1)
C
Center holer (1)
D
T-Valve (1)
P
Elbow with
Spout (1)
Q
4”Clear Tubes (3)
R
Drain Plug (1)
S
Funnel Spinner Assembly (3)
T1 T2 T3

4
Dump Bucket Assembly (2)
U1
U2
Boat (1)
V
Bucket (1)
Y
Hose Connector
Stem (1)
Z
Funnel (1)
X
Cup (1)
W
Outside U.S.A and Canada
À l’extérieur des États-Unis et du Canada
Fuera de EE.UU. y Canadá
Fun Tag (1)
AA
Hose
Connector
Washer (1)
BB CC
DD
Hose
Adapter (1)
Hose
Connector (1)

5
1
Let’s get started!
First insert the drain plug (part S) into opening
on table top (part A)
Push drain plug through the opening.
A
S
Close the drain plug.
1
3
Recommended
(not included)
2
Next, ip table over.
Work the plug around the
opening, pulling only the
plug edge through.
The plug edge
should be
completely
pulled through

6
1
Place on at
surface before you
push legs in
Attach the legs
2
Insert 3 table legs (part B) into table top (part A),
snap into place.
Bx3
A
Snap!
23
B
B
Snap!

7
The funnel is a snap!
First, place center funnel (part E) upside down on a table.
Then place center holder (part D) upside down on the center funnel.
E
D
Ensure opening for tube is
positioned through center holder.
Press down until you hear a snap!
Snap!
3

8
4
Add the bubble tube and hose!
First, insert the center bubble tube (N) into the assembled funnel.
N
Push completely down
until ridge rests against the
funnel opening.
Then, insert the end of
the hose (part C) onto the
opening in the funnel.
PUSH tube down.
Insert center connector
assembly (part H) onto the
bottom of the bubble tube.
C H

9
5
Snap in the columns!
Press center cap onto connector
assembly while inserting the (3)
center columns.
Then snap the (3) center columns into
the center cap.
Insert the (3) center columns (part G) into the
center holder. Snap into place.
Snap!
Gx3
6
Center it
First thread ribbed end of clear tubing up and
through the opening directly behind the “U”
shaped cut out on the center cap (F) as shown.
F1 2
3
Snap!

7
The hose goes through the table
Feed open end of the hose through the CORNER opening in
the center of the table top (part A) (as shown).
10
A
Snap!
ALIGN NOTCHES on the center cap
(part F) to the nothces on the table. Snap into place.
F