Little Tikes LT0943 User manual

Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Page 1 of 14
11APR22
Rev. A
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
Installation Guide
1. Concrete for footings, wheelbarrow or mixer, 5 gallon bucket, water supply
2. Digging equipment for footings (spade shovel, post hole digger, auger)
3. Bracing materials (2x4s, wood pieces, concrete blocks, bricks, jackstands, sawhorses, etc.)
4. Tape measure and level
5. Open end wrench set, Allen and 6-lobe wrenches or bits, socket set, screwdrivers
6. Drill, bits, extension cords, power supply
7. Rubber mallet
8. Step ladder
9. Adult installers - 2 minimum
TOOLS AND EQUIPMENT REQUIRED
Also see "Installations 101"
MODEL DESCRIPTION PAGE
LT0943 5" 2 Seat Arch Swing W/AW 2
LT0945 5" 2 Seat Arch Swing Add-A-Bay W/AW 3
LT0947 5" 1 Seat Arch Swing W/AW 4
LT0949 5" 1 Seat Arch Swing Add-A-Bay W/AW 5
Note: An (*) by a part number (Code) indicates: Color Code Required.
IMPORTANT! Prior to installation of any components, refer to the "Owner/Operator Manual". This
manual will provide important information pertaining to site preparation, footings, system stabilization and
other necessary information vital to the success of your installation.
NOTE: Inspect equipment on a regularly scheduled basis. Refer to Playground
Inspection/Maintenance and Repair Guidelines located in Installation Manual.
Anti-Wrap Swing Swivel should be inspected monthly to ensure there are no worn,
sharp, vandalized or rusted components. It should also be determined at this time if
more grease is required to keep Swivel moving freely.
I800053
5" Arch Swing Frame
w/Antiwrap (2022)

Page 2 of 14
11APR22
Rev. A
Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
LT0943
Footing Layout - Same spacing for inground and surface mount.
5" 2 Seat Arch Swing
w/Anti-Wrap Swing Hangers
Protective Area: 24' x 32'
Top View - Surface Mount
Inground Model
Shown
3429mm [11' 3"]
457mm [18"] DIA. X
610mm [24"]
DEEP FOOTING
(4) REQ'D
1219mm
[4']
Top View - Inground
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB

Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Page 3 of 14
11APR22
Rev. A
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
Inground Model
Shown
Each Add-A-Bay for these
two models use the footing
layout shown at left.
Note: For more than eight
bays, please contact your
service representative.
LT0945
5" 2 Seat Arch Swing Add-A-Bay
w/Anti-Wrap Swing Hangers
Protective Area: 24' x 32'
Footing Layout - Same spacing for inground and surface mount.
Top View - Surface Mount
457mm [18"] DIA. X
610mm [24"]
DEEP FOOTING
(4) REQ'D
3429mm [11' 3" ]
Top View - Inground
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
1219mm
[4']

Page 4 of 14
11APR22
Rev. A
Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
Inground Model
Shown
LT0947
5" 1 Seat Arch Swing
w/Anti-Wrap Swing Hangers
Protective Area: 21' x 32'
Footing Layout - Same spacing for inground and surface mount.
Top View - Surface Mount
457mm [18"] DIA. X
610mm [24"]
DEEP FOOTING
(4) REQ'D
2235mm [7' 4" ]
1219mm
[4']
Top View - Inground
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB

Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Page 5 of 14
11APR22
Rev. A
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
Inground Model
Shown
Each Add-A-Bay for these
two models use the footing
layout shown at left.
Note: For more than eight
bays, please contact your
service representative.
LT0949
5" 1 Seat Arch Swing Add-A-Bay
w/Anti-Wrap Swing Hangers
Protective Area: 21' x 32'
Footing Layout - Same spacing for inground and surface mount.
Top View - Surface Mount
457mm [18"] DIA.
X 610mm [24"]
DEEP FOOTING
(4) REQ'D
2235mm [7' 4"]
1219mm
[4']
Top View - Inground
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB
TOLERANCES UNLESS OTHERWISE STATED LINEAR: >0MM => 100MM
1MM
>100MM => 1500MM
2MM
>1500MM => 3000MM
3MM
>3000MM
6MM
ANGULAR
1
98.00
2489
55.99
1422
01
INITIAL RELEASE 02NOV21
MSB
REV
ECN
DESCRIPTION
DATE
DRN
CHK'D
APP'D
REVISIONS
FRAME - 5.00" STEEL ARCH SWING (SM)
1 OF 2
WEIGHT:
REV:
DRG No.
TITLE:
APPR0VAL/DATE
CHECKED/DATE
DRAWN BY/DATE
DIMENSIONS ARE IN MM UNLESS STATED OTHERWISE
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE PROPERTY
OF PLAYPOWER. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF PLAYPOWER IS
PROHIBITED.
01
-
- -
929426
- - -
DO NOT SCALE
929426
SHEET:
MAT'L: AS INDEXED
SW
133.3
LB

Page 6 of 14
11APR22
Rev. A
Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
PARTS IDENTIFICATION
PN 929419* TOP
RAIL-3.5"OD X 79.58"
(ANTI-WRAP)
PN 929418* TOP RAIL-
3.5"OD X 126.58"
(ANTI-WRAP)
PN 929414* FRAME - 5.00"
STEEL ARCH SWING
PN 929415* FRAME - 5.00"
STEEL ARCH SWING (ADD
BAY)

Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Page 7 of 14
11APR22
Rev. A
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
PN 102422 ANTI WRAP SWING HANGER 3 1/2" TOP RAIL
PARTS IDENTIFICATION
EXPLODED VIEW
ASSEMBLED VIEW
PN 929427* FRAME-5.00" STEEL
ARCH SWING (ADD BAY)SM
PN 929426* FRAME-5.00"
STEEL ARCH SWING (SM)

Page 8 of 14
11APR22
Rev. A
Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
1a. Refer to Footing Layout and Construction Drawings for inground and surface mount footing
criteria for installation. Surface mount model can be placed on either a 4" concrete slab or a
concrete footing. For inground footings, place blocking material in bottom of footing holes.
Note: Do not pour concrete for footings until model is fully assembled per instructions
and braced in position, leveled and plumbed.
STEP 1 DIG FOOTINGS (IF APPLICABLE)
STEP 2 MARK TOP RAILS FOR HANGER PLACEMENT
2a. Mark top rails for anti-wrap swing hanger placement. Measure from end of top rail to center
of anti-wrap swing hanger as shown below.
2' [610mm]2' 4" [706mm]
2' [610mm] 2' [610mm]2' 4" [711mm]2' 1" [642mm]
PN 929419* TOP RAIL-3.5"OD X 79.58" (ANTI-WRAP)
PN 929418* TOP RAIL-3.5"OD X 126.58" (ANTI-WRAP)

Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Page 9 of 14
11APR22
Rev. A
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
STEP 3 ASSEMBLE AND ATTACH ANTI-WRAP SWING HANGERS
3a. Locate anti-wrap swing hanger. Remove H-shackle using a wrench with pin hole to remove
tamper proof bolt. Set bolt aside. Open hanger into halves and remove plastic collar.
3b. Illustration 1 - Centering plastic collar on mark made on top rail in Step 2, set top half on
rail. Attach with included hardware as shown.
3c. Illustration 2 - Repeat with bottom collar half. NOTE: Plastic collar halves will NOT
COMPLETELY MATE on top rail. Align tab with notch, and ensure gap between collar
halves is equal on both sides of top rail.
3d. Illustration 3 - Place steel hanger around plastic collar.
TOP RAIL
P/N 102422
ANTI WRAP
SWING HANGER
AW-HANGER-B.WMF
(2)
(1)
(3)
(4)
APPLY VIBRA-TITE
THREAD LOCKER
3e.Illustration 4 - Apply loctite
threadlocker to end of tamper
proof bolt. Attach H-shackle to
hanger via tamper proof bolt.
Tighten all hardware.
3f. Using a grease gun, place
a sufcient amount of all purpose
grease into grease tting to allow
hanger to swing freely.
LOCTITE

Page 10 of 14
11APR22
Rev. A
Arch Swing Frames 5" & Add-A-Bays 5" with Anti-Wrap Swing Hangers
Arch Swing Frames 5" with Anti-Wrap Swing Hangers
(inground and surface mount) 2 Seat, 2 Seat Add-A-Bay, 1 Seat, 1 Seat Add-A-Bay
I800053
STEP 4 FASTEN TOP RAIL TO ARCHES
4a. Set arches on ground with stubs facing each other. Firmly seat ends of top rail over
each arch stub, aligning mating bolt holes.
4b. Install bolts through top rail and arch stub in two places; repeat at other end of top rail.
5a. Repeat Step 4 for remaining arches and top rails, if applicable.
5b. For inground model, lift frame assembly and set in footings. Surface mount model will be
attached to concrete with anchor bolts in Step 6. Ensure that frame arches are plumb and
that top rails are level. Block in position so that bottom surface of top rails are 96" (8'- 0")
from nished grade. Ensure all hardware is securely tightened.
STEP 5 SET FRAME ARCH INTO FOOTINGS
Install Tip: Once top rail is in stub, all eight bolt holes must be aligned. If necessary
for alignment, run a 11/16" drill bit through all eight holes. Do not allow bit to wander,
creating a larger hole.
PN 200002145
BOLT M8 X 1.25 FEMALE
10.3 X 30 MM
(2) REQ'D
PN 200142931
ROD THREADED M8 X
75MM-PARTS ROOM
TOP RAIL
FRAME
ARCH