Living & Co Waipoua User manual

Job no.
Waipoua Queen Bedframe
INSTRUCTION MANUAL
Maximum recommended weight is 200kg
162.2cm
102.5cm
212.8cm

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
2
120Min
Approximate Assembly Time
2 Person Assembly
Floor Area 3m
x 4m
Required Assembly Space
Tools Required
Assembly Details

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
3
1. For the protection of your furniture, we recommend that the product is
placed on a protected surface during assembly to prevent damage
2. Please check that all parts are present before you start the assembly of
your furniture
3. For ease and speed of assembly, we recommend that you identify all the
parts required for each step before commencing with assembly
4. For larger items, please ensure that you have sufficient space (as
indicated on page 1)
5. We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily
6. During Assembly, please take care not to over-tighten hardware as this
may damage the product
7. Always place the product on a steady and stable surface
8. Do not use the product as a stepladder
9. This product is intended for indoor, household use only as it is a non-
industrial product
✓Please periodically check all fittings and re-tighten as necessary
✓To clean your item, please use a damp cloth and wipe clean
✓Never allow any kind of liquid on your furniture
✓Please do not place hot items (e.g. Hot drinks) directly on to the surface
Tips before you start
Care and Maintenance

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
4
QTY
PART
MEASUREMENTS
NOTES
1
Headboard Top
1622 x 92 x 25mm
Laminate on both sides
1
Headboard LH End
1000 x 80 x 25mm
Laminate on both sides (green mark on back)
1
Headboard RH End
1000 x 80 x 25mm
Laminate on both sides (red mark on the back)
1
Headboard Top Panel
1560 x 500 x 15mm
Laminate on one side
1
Headboard Bottom Panel
1560 x 500 x 15mm
Laminate on one side
2
Side Rail
2050 x 196 x 30mm
Laminate on one side
1
Centre Rail
2050 x 148 x 15mm
Plain (unfinished)
1
Footboard
1560 x 396 x 25mm
Laminate on both sides
5
Bed Slat
1510 x 350 x 15mm
Plain (unfinished)
Parts List
15 x Cams
(15mm)
14 x
Connecting
Bolts
6 x Dowels
8xPanhead
Screws
8xNail on
Glides
15 x H5
Large Screw
40 x 25mm
Woodscrew
Hardware List
6 x Bed
Bracket Slot
6 x Bed
Bracket Type 1
6 x Bed
Bracket Type 2

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
5
The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this
system works.
Cam Installation & Operation Guide
Press the cam fitting into the hole
provided. The arrow on the top of the
cam must point to the connecting
hole in the edge of the board.
Screw the connecting bolt into
the hole as shown. Screw in until
the plastic sleeve touches the
board.
Fit the two pieces of board
together. The head of the
connecting bolt must fit up
into the cam fitting.
Turn the cam fitting in a clockwise
direction to lock the boards together.
The cam fitting should turn between
¼ & ½ a turn.

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
6
•To begin assembly, lay the Top down with the holes facing up on a clean and clear surface.
•Screw six Connecting Bolts into the holes as shown.
•Insert the two Dowels into the holes as shown.
Assembly
STEP 1: Headbaord Top
Connecting Bolts
Dowels
Connecting Bolt
Dowel

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
7
•Lay the LH end down with the holes facing up on a clean and clear surface.
•Insert the cam into the large hole as shown on page 5. Ensure they are inserted in the right orientation.
•Screw in the four connecting bolts in the holes indicated below.
•Tap the nail on glide into the centre of the base of the end.
•Repeat these steps for the RH end.
Nail on Glide
STEP 2: LH & RH Headboard Ends
Connecting Bolt
Cam
Nail on Glide
Connecting Bolt
Cam

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
8
•Lay the headboard top panel with the holes facing up on a clean and clear surface.
•Insert the eight Cams into the holes as shown on page 5. Ensure they are inserted in the right
orientation.
Cams
STEP 3: Headboard Panels
Cams
Cams
Dowels
•Lay the headboard bottom panel with the holes facing up on a clean and clear surface.
•Insert the four Cams into the holes as shown on page 5. Ensure they are inserted in the right orientation.
•Insert the Dowels in the four holes in the top of the panel.
•Tap the two Nail on Glides into the bottom of the panel as indicated below.
Nail on Glides
Nail on Glide
Dowel
Cam

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
9
•Flip the headboard bottom panel over and lay down with the cams facing down, finished side up.
•Place three brackets over the small pre-drilled holes and insert the four 25mm Woodscrews in each
one as shown below. Ensure the slots in the brackets on the sides are closest to the edge of the
panel and the centre bracket has the slot on the RH.
•Repeat the installation of the brackets on the footboard the same way however ensure the centre
brackets has the slot on the LH side.
•Tap the four Nail on Glides into the bottom (unfinished edge) of the footboard as indicated below.
STEP 4: Bed Brackets
Bed Bracket Slot
Bed Bracket Slot
Nail on Glides
25mm Woodscrew
Bed Bracket Slot
25mm Woodscrew
Nail on Glide

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
10
•Lay one of the Side Rails finished side down on a clean clear surface.
•Position the Bed Brackets over the holes at each end of the rail ensuring the type 1 and 2 are at
opposite ends as shown below.
•Insert the four 25mm Woodscrews in each of the brackets.
•Repeat these steps for the second Side rail.
•Repeat these steps for the Centre Rail and insert the 15mm Panhead screws into the four holes in
each bracket. Ensure the brackets are screwed to the face with the indented rebates and the pre-
drilled holes in the edge of the rail are on the top edge.
STEP 5: Side Rails
Bracket Type 1
25mm Woodscrew
Bracket Type 2
Panhead Screws
25mm Woodscrew
15mm Panhead Screw
Pre-drilled holes
Rebate

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
11
•Bring all the components for the headboard together including the Top the LH and RH Ends the
Top Panel and the Bottom Panel.
A. Join the Top and Bottom Panel as show below by inserting the dowels into their appropriate holes.
B. Then attach the LH and RH Ends by inserting the connecting bolts into the holes on the side of the
Panels then tighten the cams as show in the instruction on page 5.
C. Finally place the Top onto the Top Panel and Ends and tighten the cams.
STEP 6: Assemble Headboard
A
B
B
C
B
B

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
12
•Attach the bed rails to the headboard and the footboard by hooking the brackets together. A second
person may be needed to assist in this step.
•First hook the bracket together at the footboard end other end of the rail onto the headboard. Ensure
hooks are pushed in tightly.
•Repeat this process for the centre and other side rail.
STEP 7: Install Bed Rails
Centre Bed rail
Side B Bed Rail
Side A Bed Rail

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
13
•Place the five slats in place an insert the H5 Large screws
STEP 8: Install the Slats
H5 Large Screw
H5 Large Screws

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
14
Congratulations, your Waipoua Queen Bed Frame is now complete.
Thank you for supporting New Zealand Made furniture.

15

16
WARRANTY
We pride ourselves on producing a range of quality products that are both packed with features and
completely reliable.
We are so confident in our products; we back them up with a five-year warranty. Now you too can relax
knowing that you are covered.
For parts and assistance, call the manufacturer direct on 0800 100 858 or email
[e-mail]. Please do not call the store you purchased the cabinet from as they will
be unable to help you.
This product is covered by five-year warranty when accompanied by proof of purchase.