Living & Co Takiwira User manual

Job no.
Tākiwira Bedside Table
INSTRUCTION MANUAL
Maximum recommended weight 15kgs per drawer
46cm
54.3cm
36.6cm

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
1
60
Min
Approximate Assembly Time 1 Person Assembly
Floor Area 3m
x 2m
Required Assembly Space
Tools Required
Assembly Details

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
2
1. For the protection of your furniture, we recommend that the product is
placed on a protected surface during assembly to prevent damage
2. Please check that all parts are present before you start the assembly of
your furniture
3. For ease and speed of assembly, we recommend that you identify all the
parts required for each step before commencing with assembly
4. For larger items, please ensure that you have sufficient space (as
indicated on page 1)
5. We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily
6. During Assembly please take care not to over-tighten hardware as this
may damage the product
7. Always place the product on a steadyand stable surface
8. Do not use the product as a stepladder
9. This product is intended for indoor, household use only as it is a non-
industrial product
Please periodically check all things and re-tighten as necessary
To clean your item, please use a damp cloth and wipe clean
Never allow any kind of liquid on your furniture
Please do not place hot items (eg. Hot drinks) directly on to the surface
Tips before you start
Care and Maintenance

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
3
QTY
PART
MEASUREMENTS
NOTES
1
Top
460 x 396 x 25mm
Laminate on one side.
1
LH End
518 x 390 x 15mm
Laminate on both sides.
1
RH End
518 x 390 x 15mm
Laminate on both sides.
1
Top Drawer Front
412 x 195 x 15mm
Laminate on one side.
1
Bottom Drawer Front
412 x 235 x 15mm
Laminate on one side.
1
Front Rail
418 x 80 x 15mm
Laminate on front side only.
1
Back Rail
418 x 80 x 15mm
Plain (both sides are unfinished)
2
LH Drawer Sides
340 x 160 x 12mm
Laminate on both sides.
2
RH Drawer Sides
340 x 160 x 12mm
Laminate on both sides.
2
Drawer Backs
368 x 155 x 12mm
Laminate on both sides.
2
Drawer Bottoms
378 x 339 x 4mm
Laminate on both sides.
1
Back Panel
463 x 438 x 4mm
Plain (unfinished)
Parts List
Hardware List
12 x
Connecting
Bolts
8 x Large
Cams
(15mm)
8 x Large
Cams
(15mm)
8 x Drawer
Slide
Screws
8 x Small
Woodscrews
16 x Dowels
4 x Panhead
Screws
4 x Nail on
Glides
2 x Metal
Drawer Slide
Sets
2 x Handles
8 x 31mm
Woodscrews

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
4
The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this
system works.
The Drawer Slide components shown above are to be attached to the cabinet. They have letters CL or CR
stamped on them to indicate left hand or right-hand components. You will need these for steps 1 and 2.
Your pack will contain two sets of Metal Drawer Slides. These are bundled together with adhesive
tape. The set comprises of 4 components. Undo the tape on one set at a time and separate the
parts.
LEFT HAND PART (DL) RIGHT HAND PART (DR)
The Drawer Slide components shown above are attached to the drawer. They have the letters DL
or DR stamped on them to indicate left hand or right-hand components. Put these parts aside for
attaching to the drawer later.
Cam Installation & Operation Guide
Drawer Slides Guide
Use these holes

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
5
•To begin assembly, lay the top finished side down on a clean and clear surface
•Screw four Connecting Bolts into the holes as shown
•Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each
slide (ensure that the end of the slide with the wheel is on the side with the finished edge).
•Insert two Large Cams as shown (make sure the arrow on the top of the Cam points towards the
top edge of the End).
•Push two Dowels into the top edge of the End
•Screw two Connecting Bolts into the holes as shown
Assembly
STEP 1: Top
STEP 2: LH End
Connecting Bolt
Connecting Bolt
Large Cam
Drawer Slide Screw
Connecting Bolt
Connecting Bolt
Connecting Bolt
Connecting Bolt
Dowel
Connecting Bolt
Cam
Drawer Slide Screw
Dowel
Cam
Drawer Slide Screw
Finished Edge
Connecting Bolt

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
6
• Repeat the previous step with the RH End.
• Install 2 Dowels and 2 Large Cams into each Rail as shown (ensure the arrow on the top of the
Cam points towards the edge of the Rail with the hole in it.
STEP 3: RH End
Connecting Bolt
Large Cam
Drawer Slide Screw
STEP 4: Rails
Dowel
Dowel
Cam
Drawer Slide Screw
Finished Edge
Connecting Bolt
Cam
Drawer Slide Screw
Connecting Bolt
Dowel
Cam
Dowel
Cam
Large Cam
Dowel

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
7
•Fit the Front Rail (the one with one finished side) over the Connecting Bolt closest to the finished
side of the End as shown (ensure the finished side of the Rail is facing forward so the cams can’t be
seen once the cabinet is completed).
•Fit the Back Rail over the other Connecting Bolt.
•Tighten the two Cams in a clockwise direction to lock the pieces together.
•Fit the Connecting Bolts installed in the RH End into the Cams in the Rails as shown below.
•Tighten the remaining three Cams in the Rails by turning them in a clockwise direction (they should
turn at least ¼ of a turn).
STEP 5: Attach Rails to LH End
STEP 6: Attach RH End
Front Rail
Back Rail
Front Rail
LH End
Back Rail
Front Rail
LH End
Back Rail
RH End

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
8
• Fit the Top to the Ends by fitting the four Connecting Bolts installed in the Top into the Cams in the
Ends. Tighten all four Cams to lock the Top to the Ends.
• Tap the four Nail on Glides into the bottom of the Ends as indicated below. Space them about
50mm in from the front and back edges.
•Carefully lay the bedside on its front edge.
•Slide the Back Panel in place
•Using the two Panhead screws provided, secure the Back Panel in place. Then stand the Bedside
upright.
STEP 7: Attach Top and Glide Feet
STEP 8: Back Panel
Front Rail
Top
LH End
RH End
H37 Nail on Glides
Nail on Glide
Panhead Screw
Top
RH End
Back Panel
LH End
RH End

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
9
Assemble the Drawers
Drawer Bottom
LH Drawer Side
Drawer Side
RH Drawer Side
Drawer Front

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
10
•Install the hardware in the Drawer parts as shown below.
Note: Be sure that the arrow on the Small Cam points to the end of the drawer side nearest i
STEP 9: Install Hardware
Connecting Bolt
Small Cam
Dowell
Connecting Bolt
DRAWER FRONT
Cam
LH DRAWER SIDE
RH DRAWER SIDE
Dowel
Dowel
Cam

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
11
•Lay the Drawer Front finishes side down on a smooth, clean surface.
•Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in
the Drawer Front.
•Turn the Small Cams in a clockwise direction to lock the Drawer Sides in place.
•Slide the Drawer Bottom into place in the grooves in the Drawer Sides and Drawer Front.
•Fit the Drawer Back into place between the Drawer Sides. The groove in the Drawer Back will fit
over the end of the Drawer Bottom.
•Secure the Drawer Sides to the Drawer Back with four Woodscrews as shown below.
STEP 10: Assemble the Drawer
Drawer Back
Drawer Bottom
2 x
Woodscrews
RH Drawer Side
Dowel
Connecting Bolt
Drawer Front
LH Drawer Side
2 x
Woodscrews
Woodscrew

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
12
•Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four
woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up
against the back of the Drawer Front. Each slide requires two screws.
STEP 11: Attach the Drawer Slides
Woodscrew
RH Drawer Slide (DR)
Woodscrew
Woodscrew
LH Drawer Slide (DL)

AFTER SALES SUPPORT
www.compacfurniture.co.nz or 0800 100 858
13
•Attach the Bar Handle to the Drawer Front using the screws provided
•Fit the drawers into the Bedside. Make sure that the rollers at the back of the drawer go behind the
front rollers in the cabinet and into the channel of the drawer slide. It helps to lift the front of the
drawer up a little when doing this.
STEP 12: Attach the Handle and Insert the Drawers
Congratulations, your Tākiwira 2 Drawer Bedside is now complete.
Thank you for supporting New Zealand Made furniture.
Angle the drawer slightly to ensure
that the wheel at the back of the
drawer slide goes behind the front
wheel on the cabinet slide. Then lift the
drawer up and slide it into the
channel of the drawer slide.

WARRANTY
We pride ourselves on producing a range of quality products that are both packed with features and
completely reliable.
We are so confident in our products, we back them up with a five-year warranty. Now you too can relax
knowing that you are covered.
For parts and assistance, call the manufacturer direct on 0800 100 858. Please do not call the store you
purchased the cabinet from as they will be unable to help you.
This product is covered by five-year warranty when accompanied by proof of purchase.