Living & Co Waipoua User manual

Job no.
Waipoua 6 Drawer Lowboy
INSTRUCTION MANUAL
Maximum recommended weight 15kgs per drawer
INSTRUCTION MANUAL
Maximum recommended weight is 15kgs per drawer
118.3cm
m
39.6cm
m
79.4cm

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
2
120Min
Approximate Assembly Time
2 Person Assembly
Floor Area 3m
x 4m
Required Assembly Space
Tools Required
Assembly Details

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
3
1. For the protection of your furniture, we recommend that the product is
placed on a protected surface during assembly to prevent damage
2. Please check that all parts are present before you start the assembly of
your furniture
3. For ease and speed of assembly, we recommend that you identify all the
parts required for each step before commencing with assembly
4. For larger items, please ensure that you have sufficient space (as
indicated on page 1)
5. We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily
6. During Assembly please take care not to over-tighten hardware as this
may damage the product
7. Always place the product on a steady and stable surface
8. Do not use the product as a stepladder
9. This product is intended for indoor, household use only as it is a non-
industrial product
✓Please periodically check all fittings and re-tighten as necessary
✓To clean your item, please use a damp cloth and wipe clean
✓Never allow any kind of liquid on your furniture
✓Please do not place hot items (e.g. Hot drinks) directly on to the surface
Tips before you start
Care and Maintenance

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
4
QTY
PART
MEASUREMENTS
NOTES
1
Top
1183 x 396 x 25mm
Laminate on one side.
1
LH End
684 x 370 x 15mm
Laminate on one side (green mark on back).
1
RH End
684 x 370 x 15mm
Laminate on one side (red mark on back).
1
Base Shelf
1091 x 352 x 15mm
Plain (unfinished).
4
Corner Legs
794 x 80 x 25mm
Laminate on both sides.
1
Division
669 x 354 x 15mm
Plain (unfinished).
4
Front Rails
538 x 50 x 15mm
Laminate on one side.
1
LH Top Drawer Front
557 x 195 x 15mm
Laminate on one side (green mark on back).
1
RH Top Drawer Front
557 x 195 x 15mm
Laminate on one side (red mark on back).
2
LH Drawer Fronts
557 x 215 x 15mm
Laminate on one side (green mark on back).
2
RH Drawer Fronts
557 x 215 x 15mm
Laminate on one side (red mark on back).
6
LH Drawer Sides
340 x 160 x 12mm
Laminate on both sides (green mark on back).
6
RH Drawer Sides
340 x 160 x 12mm
Laminate on both sides (red mark on back).
6
Drawer Backs
488 x 155 x 12mm
Laminate on one side.
6
Drawer Bottoms
498 x 339 x 4mm
Laminate on one side.
1
Back Panel
694 x 1111 x 4mm
Plain (unfinished).
Parts List
Hardware List
26 x
Connecting
Bolts
18 x Large
Cams
(15mm)
12 x Small
Cams
(12mm)
24 x Drawer
Slide
Screws
24 x Small
Woodscrews
30 x Dowels
9 x 15mm
Panhead
Screws
4 x Nail on
Glides
6 x Metal
Drawer Slide
Sets
36 x 31mm
Large
Woodscrews
4 x Short
Connecting
Bolts
2 x Washer
1 x Safety
Strap
2 x H5 Large
Screw

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
5
The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this
system works.
The Drawer Slide components shown above are to be attached to the cabinet. They have letters CL or CR
stamped on them to indicate left hand or right-hand components. You will need these for steps 1 and 2.
Your pack will contain six sets of Metal Drawer Slides. These are bundled together with adhesive
tape. The set comprises of 4 components. Undo the tape on one set at a time and separate the
parts.
LEFT HAND PART (DL) RIGHT HAND PART (DR)
The Drawer Slide components shown above are attached to the drawer. They have the letters DL
or DR stamped on them to indicate left hand or right-hand components. Put these parts aside for
attaching to the drawer later.
Cam Installation & Operation Guide
Drawer Slides Guide
Use these holes

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
6
•To begin assembly, lay the top finished side down on a clean and clear surface.
•Screw six Connecting Bolts into the holes as shown.
•Using the Panhead screw, attach the Safety Strap as shown by screwing it first through the
Washer and then through the eyelet in the Strap, into the hole in the left-hand side of the Top. Make
sure that the Strap is positioned so that the tail end falls through the hole in the edge of the Top as
shown below.
Assembly
STEP 1: Top
Connecting Bolt
Panhead Screw
Safety Strap
Washer
Safety Strap
Connecting Bolts
Screw the
Panhead
screw through
the Washer.

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
7
•Screw the legs onto the LH end using the 31mm gold screws. Ensure the guide holes in the end
match up with the guide holes on the leg before inserting the screws.
•Tap the Nail on glides into the base of the legs using the guide holes provided.
STEP 2: Screw Legs to LH End
Nail on Glide
Large Woodscrew
Screw
Large Woodscrew
screw
Finished Edge
Large Woodscrew
screw
Nail on Glides

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
8
•Repeat the previous step with the RH End.
Nail on Glide
STEP 3: Screw Legs to RH End
Nail on Glide
Large Woodscrew
Screw
Large Woodscrew
Finished Edge
Large Woodscrew

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
9
•Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each
slide (ensure that the end of the slide with the wheel is on the side with the finished edge).
•Insert two Large Cams as shown (make sure the arrow on the top of the Cam points towards the
top edge of the End).
•Push two Dowels into the top edge of the End.
•Screw three Connecting Bolts into the holes as shown.
Dowel
Cam
Drawer Slide Screw
Finished Edge
Connecting Bolt
STEP 4: Hardware LH End
Connecting Bolt
Drawer Slide Screw
Connecting Bolt
Large Cam
Drawer Slide
Screw
Dowel

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
10
•Repeat the previous step with the RH End.
STEP 5: Hardware RH End
Dowel
Cam
Finished Edge
Connecting Bolt
Drawer Slide Screw
Connecting Bolt
Drawer Slide Screw
Connecting Bolt
Large Cam
Drawer Slide
Screw
Dowel

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
11
•Install the hardware in the Division as shown below. NOTE: The holes for the Cams could be on
either side of the Division.
•Repeat this step for both sides of the division. Ensure that the end of the slide with the wheel faces
towards the Finished edge of the Division.
STEP 6: Division
Cam
Dowel
Short Connecting Bolt
Large Cam
Drawer Slide
Screw
Dowel
Finished Edge
Drawer Slide Screws
Drawer Slide Screws
Short Connecting Bolt

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
12
Your pack will contain the following rails a base shelf.
•4 x Front Rails
•1 x Base Shelf
•Install the Large Cams into each piece as indicated.
•Push the Dowels into each of the boards as indicated.
STEP 7: Rail and Shelf
Large Cam
Dowel
Dowels
Large Cams
Large Cam
Dowels
Dowels

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
13
•Lay the Top on a clean, clear surface.
•Attach the LH End to the Top by fitting it down over the Connecting Bolts installed in the Top. Make
sure the Finished edge of the LH End faces the front of the Top. Then tighten the cams as show on
page 5.
•Fit the two Front Rails over the Connecting Bolts in the End as shown (ensure the finished side of
the Rail is facing forward so the cams cannot be seen once the cabinet is completed). Then tighten
the cams, ensure you don’t over tighten the cams, or this may split the side of the rail.
STEP 8: Attach LH End to Top
Top
LH End
Front Rails

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
14
•Attach the Division to the Top by fitting it down over the Connecting Bolts installed in the Top. Make
sure the Finished edge of the Division faces the front of the Top. Then tighten the cams as show on
page 5.
•Also fit the Connecting Bolts in the division into the cams in the Front Rails. Then tighten the cams,
ensure you don’t over tighten the cams, or this may split the side of the rail.
STEP 9: Attach Division to Top
Division
Unfinished Edge
Front Rails

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
15
•Install the Base Shelf by fitting the shelf into Connecting Bolts in the LH end as shown below.
Ensure the finished edge of the shelf is facing forward, then tighten the cams as show on page 5.
STEP 10: Fit the Base Shelf
Finished Edge
Base Shelf

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
16
•Attach the RH End to the Top by fitting it down over the Connecting Bolts installed in the Top. Also
insert the connecting bolts in the ends of the front rails and base shelf. Then tighten the cams as
show on page 5.
•Then install the Large H5 Screws into the holes in the centre of the shelf.
STEP 11: Attach RH End to Top
RH End
Large Screw
H5 Large Screw

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
17
•Slide the Back Panel in place.
•Using eight Panhead screws provided, secure the Back Panel in place using the predrilled holes in
the back panel. Then stand the Lowboy upright.
STEP 12: Back Panel
Panhead Screw
Panhead Screws
Panhead Screws

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
18
•Install the hardware in the Drawer parts as shown below.
Note: Be sure that the arrow on the Small Cam points to the end of the drawer side nearest it.
Assemble the Drawers
Drawer Bottom
LH Drawer Side
Drawer Side
RH Drawer Side
Drawer Front
STEP 13: Install Hardware
Connecting Bolt
Small Cam
Dowell
Connecting Bolt
DRAWER FRONT
Cam
LH DRAWER SIDE
RH DRAWER SIDE
Dowel
Dowel
Cam

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
19
•Lay the Drawer Front finishes side down on a smooth, clean surface.
•Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in
the Drawer Front.
•Turn the Small Cams in a clockwise direction to lock the Drawer Sides in place.
•Slide the Drawer Bottom into place in the grooves in the Drawer Sides and Drawer Front.
•Fit the Drawer Back into place between the Drawer Sides. The groove in the Drawer Back will fit
over the end of the Drawer Bottom.
•Secure the Drawer Sides to the Drawer Back with four Woodscrews as shown below.
•Repeat this step for all 6 drawers.
STEP 14: Assemble the Drawers
Large Woodscrew
Screw
Drawer Back
Drawer Bottom
2 x Large
Woodscrews
RH Drawer Side
Dowel
Connecting Bolt
Drawer Front
LH Drawer Side
2 x Large
Woodscrews

AFTER SALES SUPPORT
[e-mail] or 0800 100 858
20
•Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four
small woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up
against the back of the Drawer Front. Each slide requires two screws.
•Repeat this step for all 6 drawers.
STEP 15: Attach the Drawer Slides
RH Drawer Slide (DR)
Small Woodscrew
Small woodscrew
LH Drawer Slide (DL)
Small woodscrew