Living Earth Crafts Nuage Series User manual

Nuage™Table Collection
USER MANUAL
Nuage™ Designer Cabinetry Series
Nuage™Vector Nuage™Vector +Studio
Nuage™Pedestal
1-400-0006 • Rev E• 6/6/18
© Living Earth Crafts 2018, All Rights Reserved
Nuage™Pedestal +Studio
*all tables shown with oponal accessories and/or nishes

© Copyright 2018
Living Earth Cras®
All rights reserved. is document or any
portion thereof may not be reproduced
in any way, including photocopying or
translation to another language without
the prior written permission from Living
Earth Cras.
Living Earth Cras® is a registered trade-
mark of Earthlite, LLC.
Legal Notice
e information provided in this document is intended
for informational purposes only and is subject to change
without notice. e information provided in this docu-
ment should not be construed as a commitment by
Living Earth Cras®.
Living Earth Cras® assumes no responsibility for the
accuracy or suitability of the information contained in
this document. is document may contain technical
inaccuracies or errors. Living Earth Cras® makes no
expressed or implied warranties of any kind concerning
the information contained in this document, including,
but not limited to, the implied warranties of merchant-
ability and tness for purpose.
Living Earth Cras® shall not be liable for incidental or
consequential damages in connection with or arising out
of the product, performance, or use of this document
and the information and material it describes.

Introduction
Congratulaons on your purchase of a table from the Nuage™ Collecon. All Nuage™ tables
are designed with advanced technology to bring you the quietest, smoothest, all-electric spa
treatment tables in the market today. Each Nuage™ table is designed from the ground up for
amazing comfort, ultra-reliability, and minimal maintenance in the most acve spa environments.
Nuage™ tables are designed for licensed therapists and are intended to be used in a professional
spa, massage studio, or similar commercial environment. While no special training is needed to
operate the table, for safety reasons it is important that the instrucons contained in this manual
are reviewed in detail before the rst use. This manual should be read in its enrety by each
professional who will be operang the table to ensure the safety of both operator and client. This
manual should be saved for future reference.
The Nuage™ table should not be used in any other manner than described in this manual.
Please read, understand, and follow all safety warnings, labels, and instrucons. Misuse, use of
unnecessary force, or using the table for unintended or unauthorized procedures can result in
injury to operator, client, and/or equipment.
Detailed instrucons for use and maintenance can be found in this user manual. If you have
further quesons, please contact us at [phone] for US customers, or [phone] for
internaonal customers. We can also be reached via e-mail at info@livingearthcras.com
Secon 1: Safety Informaon
Safety Symbols
Warnings & Grounding Instrucons
Secon 2: Product Overview
Product Photos & Specicaons
Secon 3: Installaon
Moving Your Table
Basic Setup
Leveling Instrucons
Weight/Li Capacies
Secon 4: Operang Instrucons
Important Safety Notes
Electrical Specicaons
Hand/Foot Control
+Studio Opons
Secon 5: Care & Maintenance
Care Instrucons
Troubleshoong
Warranty Informaon
Contact Us
2
2-3
4-5
6
6
7
7
8
8
9
10-14
15
16
17
Table of Contents
back cover

READ AND SAVE THESE INSTRUCTIONS
2
IMPORTANT SAFETY INSTRUCTIONS - FOR COMMERCIAL USE ONLY
Read all instructions before using this product.
Safety Symbols
Familiarize yourself with the following
Safety & Warning symbols. They are
designed to prevent damage and injury to
you, your clients, and your new Earthlite
product.
IMPORTANT: The important safety
instructions and warnings in this manual
cannot cover all possible problems and
conditions that can occur. Use common
sense and caution when installing,
operating, or maintaining this appliance.
Indicates an imminently hazardous
situation which could result in serious
or fatal injury.
Indicates a potentially hazardous
situation which could result in serious
injury.
Indicates a potentially hazardous
situation which could result in
equipment damage and/or injury.
SECTION 1: SAFETY INFORMATION
1) Always unplug this furnishing from the electrical outlet before servicing.
2) Never use this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the furnishing to a service center for examination
and repair.
3) Keep the cord away from heated surfaces.
4) Do not use outdoors.
5) Do not operate where aerosol (spray) projects are being used or where oxygen is being administered.
6) To disconnect, turn all controls to the off position, then remove plug from outlet.
7) Connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
RISK OF ELECTRIC SHOCK, FIRE, AND EXPLOSION
INTERNATIONAL VERSIONS ONLY
This product is for use on a nominal 220V-240V cir-
cuit and has a grounding plug (plug type varies by
country). Make sure that the product is connected
to an outlet having the same conguration as the
plug. No adapter should be used with this product.
NORTH AMERICA ONLY
Grounded
Outlet Box
Grounded Outlet
Grounding Pin
GROUNDING INSTRUCTIONS:
POWER SUPPLY: (120V AC grounded) Electrical limitations: Do not use extension cord with this product, plug
directly into grounded outlet. This product must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-grounding conductor and a grounding plug. This three prong grounded plug
will only t into wall outlet one way. If the plug does not t fully in the outlet, contact a qualied electrician to
install the proper outlet. Do not change the plug in any way.

READ AND SAVE THESE INSTRUCTIONS 3
2) When lowering the table height, be sure there are no foreign obstacles are underneath your table
that could obstruct it from lowering completely. This could damage your table.
3) Never set anything under the table frame to avoid collision if lowered.
4) Never operate your table on an uneven surface. Adjust the leveling feet so that your table is stable.
5) Never raise the head or leg section with a client in the prone position (face down.)
6) Never use or store your table in a wet or very humid environment. Water and excessive moisture
can damage the wood cabinet and electrical components. Evidence of exposure to water or
moisture will void your warranty.
7) If you have purchased the Flexible Armrest Option, never use the Armrests as handholds or body
support mechanisms, especially when setting clients on or off the table.
8) Never drop or insert any object into any opening.
SECTION 1: SAFETY INFORMATION
1) Use this furnishing only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
2) Do not operate this equipment unless properly trained.
3) Install this furnishing in treatment area not accessible to the public.
4) Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled
persons.
5) This product does not have “pinch point” protection. Only operate when no possibility of any portion
of the body could be caught and injured while moving the table top upward/downward, or activating
the back/foot tilt.
6) Do not use this furnishing to support video equipment such as televisions or computer monitors.
7) Never attempt to use the Head or Leg lift section to support concentrated weight such as sitting
or standing
To reduce the risk of burns, re, electric shock, or injury to persons:
1) When lowering any section of the table, make sure that no supplies or any part of
yours or your client’s body is between the top of your table and its base. This could
result in injury, or could damage your table as well as the item. It is recommended
that you always return your table top to the lowest at position to avoid leaving the
base exposed.

Product Image*
Available Tops Flat, Electric Salon Flat, Electric Salon
Top Length 73” 73”
Top Width 30” or 32” 30” or 32”
Top Cushioning Strata 4” Memory Foam Strata 4” Memory Foam
Top Corner Style Round Round
Top Degree of Tilt
(Electric Salon Only)
Back TIlt: 0° - 70°
Leg Tilt: 0° - 43°
Back TIlt: 0° - 70°
Leg Tilt: 0° - 43°
Height Range 25” - 37” 25” - 37”
Cord Exit Locaon Head end of table Head end of table
Diagnosc Panel Locaon Centered inside cabinet Centered underneath top
Base 3 Cabinetry Opons Pedestal Base
Base/Cabinet Measurements
Tradional, Contemporary
52.5” x 23.25” x 21”
Cuvee
54.5” x 23.75” x 21”
51.5” x 22.25” x 21”
Base Construcon Cross braced steel frame
Hardwood Maple cabinet
Cross braced steel frame
Hardwood Maple base
Included Accessories
Programmable Hand Control X X
Foot Control X X
PowerPort Outlets X X
Salon Style Neck Roll X X
Embedded Table Warmer
Smart Tablet
Strata FacePillow w/Plaorm
LED/Chromatherapy Lighng
SO Sound
Stereo Speaker
Aromatherapy System
Warming Drawer1
SECTION 2: PRODUCT OVERVIEW
*all tables shown with oponal accessories and/or nishes. Measurements may vary due to natural material variaons.
1 - see Warming Drawer User Manual for instrucons for use.
4

SECTION 2: PRODUCT OVERVIEW
Electric Salon Electric Salon Electric Salon
73” 73” 73”
30” or 32” 30” or 32” 30” or 32”
Strata 3” Memory Foam
(+ 1” embedded warmer)
Strata 3” Memory Foam
(+ 1” embedded warmer)
Strata 3” Memory Foam
(+ 1” embedded warmer)
Square Square Square
Back TIlt: 0° - 70°
Leg Tilt: 0° - 43°
Back TIlt: 0° - 70°
Leg Tilt: 0° - 43°
Back TIlt: 0° - 70°
Leg Tilt: 0° - 43°
25” - 37” 25” - 37” 25” - 37”
Head end of table Head end of table Head end of table
Underneath back lt secon Centered underneath top Centered underneath top
Pedestal Base Dual Pedestal Base Dual Pedestal Base
51.5” x 22.25” x 21” 51.5” x 22.25” x 21” 51.5” x 22.25” x 21”
Cross braced steel frame
w/laminate
Cross braced steel frame
w/laminate
Cross braced steel frame
w/laminate
X X X
X X X
X X X
X X X
X X
X
X
X X X
X
X
X
X
5

SECTION 3: INSTALLATION
Moving Your Table
• To avoid damage to your Nuage™ table, it is very important that it only be li ed from
certain posi ons on the table (table edges marked with ARROWS below)
• You may need to plug in your table and raise the table, the back sec on, and/or the leg
sec on for easier access to the base for li ing purposes.
• Li your table by grasping  rmly from the bo om of the frame. Do not try to li from the
 ns on the Cuvee cabinet or the cabinet doors.
Nuage Cabinetry Models Nuage Pedestal Models
Nuage Vector Models
Your Nuage™ table comes completely assembled and ready to use.
Ensure you read and follow the unpacking instruc ons included with your shipment.
If you did not receive unpacking instruc ons, please contact L∙E∙C customer service before
unpacking your table.
Once the table is unpacked, follow the “Moving Your Table” instruc ons below.
Basic Setup Instructions
Once your Nuage™ table is posi oned for use, follow these steps:
• Plug the power cord into a grounded outlet that is properly rated for the table.
• Arrange and secure the power cord so it will not create a tripping hazard.
• Place the hand and foot controls in loca ons where they are safe and accessible.
• Ensure the controls are not in danger of being crushed by the li or  lt mechanisms.
• Follow the “Leveling Your Table” instruc ons on the next page.
6
Your Nuage table is very heavy - extreme cau on should be used to avoid
injury to yourself, others around you, and your table. DO NOT li or move
without using proper safety procedures/equipment. DO NOT turn the table
on its side for any reason.

Leveling Your Table
Leveling, or balancing, your table is very important during ini al setup and rou ne maintenance.
Your Nuage™ table is equipped with leveling feet that can adjust to uneven fl oors.
To adjust the leveler feet:
1. Place the table in the posi on you plan to use it.
2. To determine which foot needs adjus ng, a empt to “rock” your table. If there is any
movement, the leg that is li ing is the one that will need adjus ng.
3. Raise table height approximately 6 inches.
4. Using your hand, or a wrench if necessary, turn the leveling foot in the needed direc on.
(Counterclockwise will lower the overall height, clockwise will raise the overall height)
SECTION 3: INSTALLATION
Table Accessories
All Nuage™ tables come with outlets at both ends, speci cally designed for providing a  xed
loca on for FacePillow pla orms, salon pillows, and other accessories.
To learn about all available accessories, visit the Living
Earth Cra s Website, or call Living Earth Cra s customer
service to request a catalog.
Weight & Lift Capacities
The Nuage table is powered by a 2 heavy-duty li columns. The
recommended li capacity is 550 lbs.
550 lbs.
The back and leg sec ons have a maximum weight capacity of 50
lbs. These sec ons are not meant to hold full body weight.
50 lbs.
Warming Drawer (Optional)
IMPORTANT: Please refer to separate Warming Drawer User Manual for safety warnings
and instruc ons for use. If you did not receive one, contact LEC Customer Service before
use to be sent an electronic copy.
7

8
SECTION 4: OPERATING INSTRUCTIONS
Always use extreme cauon when making any posion adjustments to
your table. Ensure all body parts and objects are clear from all moving parts.
The described adjustments can be done with a client on the table, but use
cauon to ensure that the client’s weight is supported while posioning the
table secon(s).
Do not sit or put unnecessary amounts of pressure on
the back secon of the table when it is in lt posion of
any level. This can damage or destroy the lt mechanism
and cause harm or bodily injury to persons. The lt
mechanism is intended solely to be used when a client
is properly seated or laying on the table top. Damage
caused in this manner may void the warranty.
Do not sit or put unnecessary amounts of pressure on
the leg secon of the table when it is in lt posion of
any level. This can damage or destroy the lt mechanism
and cause harm or bodily injury to persons. The lt
mechanism is intended solely to be used when a client
is properly seated or laying on the table top. Damage
caused in this manner may void the warranty.
Important Safety Notes
DO NOT store or place anything under the backrest - this can damage the
top and/or lng mechanism and will void your warranty. This area is not
designed for storage or as an area to hold accessories and/or massage
supplies while performing any type of service.
DO NOT store or place anything between the table and the base - this can damage
the table and/or base and will void your warranty. The base of the table is not
designed for storage or as an area to hold accessories, including foot pedal.
Electrical Specications
Spec North America Europe/Asia
Input Voltage 120 VAC 220 VAC
Input Frequency 60 Hz 50 Hz
Consumpon 7.7 Amps, 925 Was 4.2 Amps, 925 Was
Output 12-24 VDC 12-24 VDC
Duty Cycle 10%, 2 min/18 min 10%, 2 min/18 min
Power Strip Rang 12 Amp Max 15 Amp Max
*Other plugs also availabe for various countries
China
220V AC
PLUG DESCRIPTION
120V AC 220V AC 220V AC
NORTH AMERICA UK / MIDDLE EAST EUROPEASIA

9
SECTION 4: OPERATING INSTRUCTIONS
Hand Control Operation
Raise Back Section Lower Back Section
Lower Leg Section
Lower Entire Table
Raise Leg Section
Raise Entire Table
Preset 2:
Enter/Exit Table
Preset 4:
Body Treatment
Preset 3:
Facial Treatment
Foot Control Operation
Preset 1:
Flat Massage
Lower Entire Table Raise Entire Table
Your Nuage™ hand control is already connected and ready for use. See below for
descripons of each buon’s funconality, including 4 convenient memory posions.
Your Nuage™ foot control is already connected and ready for use. The foot control allows
you to simply raise and lower the table, allowing convenient hands-free adjustments.
Always use extreme cauon
when making any posion
adjustments to your table.
Ensure all body parts and
objects are clear from all
moving parts.

10
SECTION 4: OPERATING INSTRUCTIONS
LED Chroma Lighting Hand Control Operation (+Studio Only)
Your +Studio table is equipped with color-changing LED accent lighng, allowing you to match
any decor or client preference. With the remote, the user can change the color to any one of
16 colors, or use the preset color changing paerns. See below for instrucons on how to use
the included remote control:
This secon of buons
will turn the LEDs to a
solid color of your choice
These two buons
adjust the dimming On/O Controls
Flashes a variety of colors
Flashes white
Smoothly fades all colors
Flashes red, green, blue
Embedded Table Warmer (+Studio Only)
Your +Studio table is equipped with an embedded table warmer, that can be operated by the
below control panel. The control panel will be mounted to your table cabinet.
Power Buon
Lower
Temperature
Raise
Temperature

SECTION 4: OPERATING INSTRUCTIONS
11
Tablet Instructions (+Studio only)
1. Click on the “Video” icon
Switch to
fullscreen
mode
Pause/Play
2. Click on the video you would like to play
Power Volume Up/Down

SECTION 4: OPERATING INSTRUCTIONS
Tablet Instructions (+Studio only)
Pull knob to adjust
lt of tablet if needed
12

SECTION 4: OPERATING INSTRUCTIONS
So Sound Overview (Nuage Vector +Studio Only)
So Sound is designed to deliver the healing frequencies of sound and music, taclely, so
you feel the sound and/or music resonang through your body and brain simultaneously
to hearing it; thus ‘reminding’ the body of it’s natural state of harmony. This sensory
integrave process eciently and eecvely restores a deeper sense of mental, emoonal,
and physical health and well-being.
Operating the So Sound System
Your tablet comes pre-connected to the So Sound system, so when you play videos (see
instrucons on previous page), it will automacally begin to resonate through the So Sound
transducers.
Resonance
Adjustment
Knob
Volume
Adjustment
Knob
13
From your
player’s
headphone
output
Output to
headphones
or speakers
with separate
power

SECTION 4: OPERATING INSTRUCTIONS
Jawbone Jambox Speaker (Nuage Vector +Studio Only)
The integrated Jawbone Jambox speaker comes pre-connected to the tablet and So Sound
system, so when you play the videos (see instrucons on page 11), it will automacally
begin to play through the speaker.
Playing the music simultaneously through both the So Sound System and the Jawbone
speaker gives a more comprehensive sensory integraon experience. Speakers are designed
to deliver music through the air, while the So Sound System is designed to deliver music
through mass. In other words, the frequency ranges that we hear are dierent from the
frequency ranges we feel. By combining the two we create a fully immersive sound healing
environment.
The image below shows the controls on your Jambox speaker - the ony funcons needing
adjustment will be the the volume controls, using the “+” and “-” buons.
Decrease
Volume
Increase
Volume
NOTE: Play/Pause/Stop of the videos will need to be controlled through the tablet
Balancing Your Audio System (Nuage Vector +Studio Only)
The intent of this exercise is to nd the opmum balance of sound and resonance
1. Have an individual lay on the table as if they were receiving treatment
2. Lower the resonance to the lowest possible level
3. Set the volume on the Jambox speaker to a medium level
4. Begin playing the videos on the tablet
5. Slowly turn the volume on the Jambox speaker to a comfortable level
6. Adjust the resonance level unl it feels good to the individual on the table
NOTE: Once the resonance level is set, it does not need to be further adjusted on the So
Sound amplier. Control both the volume of the speaker and resonance level by changing
the volume on the tablet.
14

SECTION 5: CARE & MAINTENANCE
Your Nuage™ table is relavely maintenance free, as the liing mechanism is enclosed
and sealed. However, to ensure your table will connue to funcon properly and keep its
appearance, we recommend the following.
Vinyl
Aer each treatmeant on your table, clean thoroughly, removing all residue.
This and other residues may cause the vinyl to dry out and become brile.
We recommend a mild detergent and warm water mix, or environmentally
friendly disinfectant cleaners, such as Viraguard®. Apply with cloth or spray
directly onto the upholstery. Ensure surface is wiped clean of residue.
Use cauon when aempng to remove stains as you could damage your
vinyl. Any stains should be treated immediately with a soluon of 1 part
alcohol to 10 parts water. Restore the luster to the spot with a light
applicaon of spray furniture wax.
Laminate
Never use abrasive cleaners. A mild liquid detergent and warm water will
clean soiled surfaces. To avoid discoloraon, cleaners containing petroleum
disllates must not remain on surfaces.
Wood To maintain the wood nish and retouch scratches, use a high quality
furniture wax.
Electronics An-stac electronic aerosol dusters can be used to keep the surfaces of
electronic components, power cables, and plugs free of dust.
Lubricaon
& Mechanical
If necessary, lubricate wheel joints, casters, foot glide levelers, ball joints,
and other mechanical parts with a light machine oil. Periodically check and
ensure all visible bolts remain ghtened.
Leveling Feet Regularly check to ensure the table is level and stable.
See page 7 for leveling instrucons.
Cleaning & Ongoing Maintenance
15
DO NOT USE acetone, “Armor All” type cleaners, citrus-based cleaners,
or industrial cleaners. These can seriously damage the upholstery. Such
damage would not be covered under warranty.
RISK OF ELECTRIC SHOCK
Always unplug this furnishing from the electrical outlet before cleaning.

SECTION 5: CARE & MAINTENANCE
This helpful troubleshoong guide will provide you with informaon about how to recognize a
problem with your table, determine possible causes, and nd a soluon.
In the event your specic situaon is not covered in this guide, please contact Living Earth Cras
so our technical support department can assist you. Beyond the troubleshoong guide below, do
not aempt to repair the table yourself. This can void your warranty.
Unauthorized service will not be covered. Please be sure to contact Living Earth Cras Customer
Service rst at [phone], [phone] Int’l.
Troubleshooting
Table does not
raise or lower
1. Ensure the table is plugged into a grounded and dedicated outlet.
2. If using a dimmer switch, ensure it is turned to full power.
3. Ensure the outlet in your room is receiving power. This can be done
by plugging in a small appliance and turning it on.
4. Ensure the switch on the aached power strip is turn on.
5. Check the fuse or circuit breaker for blown fuse or tripped breaker.
6. Ensure the controls are securely plugged into the juncon box.
Table does not
operate in
accordance with
funcons on
hand control
1. Ensure the controls are securely plugged into the juncon box.
2. Perform a table reset (see instrucons below).
1. Locate your table’s diagnosc panel (See Product Overview table, pages 4-5)
2. Press the “down” buon to lower table to lowest point.
3. Press the “down” buon and hold unl table moves slightly to signal reset inializaon.
4. Press the “up” buon to bring table to highest point, and connue to hold the “up” buon
unl table moves slightly to signal reset progression.
5. Press the “down” buon to bring the table down approximately 2 inches.
6. Press the “up” buon to bring table to highest point, and connue to hold the “up” buon
unl the table moves slightly to signal reset progression.
7. Press the “down” buon to bring the table down approximately 2 inches.
8. Press the “up” buon to bring table to highest point, and connue to hold the “up” buon
for several seconds. No movement should occur, signaling that the reset is complete.
Table Reset
Follow these steps to perform a reset of your table - you will be using your table’s diagnosc
panel to cycle the control box and actuators.
16

SECTION 5: CARE & MAINTENANCE
17
Warranty Information
Living Earth Cras (L∙E∙C) oers an industry best warranty against defects in materials, design,
and workmanship, to the original owner, as follows:
• Frame - lifeme warranty*
• Foam and upholstery covering - warranted for three (3) years
• Motors, controls, electronics - warranted for two (2) years, including parts and labor
• Accessories and opons - warranted for one (1) year, unless otherwise noted
L∙E∙C may repair or replace defecve components at our discreon. L∙E∙C will return the warranted
product, standard shipping pre-paid, to customers in the connental US. Internaonal customers
are responsible for any applicable dues and taxes, as well as all shipping charges inbound and
outbound. Normal wear and tear, and costs associated with maintenance procedures, and
damage caused by accident, misuse, improper maintenance, harsh operang environments or
neglect (which includes tears in the upholstery and damage caused by harsh chemical-based
cleaners) are not covered under this warranty. All warranes are limited to repair or replacement,
at L∙E∙C’s discreon, unless otherwise stated.
*Lifeme warranty applies to the original owner, as long as you own your table for 5 years aer
the model is disconnued, or 5 years for private label tables.

Visit us online at: livingearthcrafts.com
Read our blog at: livingearthcrafts.com/blog
Join us on Facebook®
Contact Us
Living Earth Crafts
990 Joshua Way
Vista, CA 92081 USA
[phone]
[phone] Int’l
[phone] fax
[email protected]
Hours of operation:
Monday - Friday
8:00 a.m. to 5 p.m. PST
Saturday - Sunday
Closed