LIXIL American Standard Cadet 2794.709 Maintenance manual

SAVE FOR FUTURE USE
7302484-100R1 10/20
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2020
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!NOTE: Pictures may not exactly define contour of china and components.
Thank you for selecting American Standard - the benchmark of fine quality for over 140 years.To ensure this product is installed properly, please read
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
TANK 4000.709
Cadet®Touchless Toilet
Models 2794.709 / 2989.709 / 215AA.709
* For seat installation, see
instructions included with seat.
Tank To Bowl
Gasket
Hand Sensor
Plastic
Washers (2)
Nuts (2)
AAA Batteries (3)
A AA A AA A AA
AA Batteries (4)
AA AA AA AA
Attachment
Handle
KIT INCLUDED WITH TANK
BOWL WITH EXPOSED TRAPWAY
Bolt Covers (2)
Bolt Caps (2) Bowl-To-Floor
Knobs (2)
T-Bolts with
Retainer (2)
KIT INCLUDED WITH BOWL
Also includes Standard
Bolt Caps (2)
BOWLS WITH CONCEALED TRAPWAY
Bowl-To-Floor
Knobs (2)
T-Bolts with
Retainer (2)
KIT INCLUDED WITH BOWLS
3517A.101
CHAIR HEIGHT ELONGATED BOWL
3075.000 / 3075.120
CHAIR HEIGHT ELONGATED BOWLS
Slow Close Toilet Seat

(3517A bowl only)
Turn Off Water Supply
Flush to remove
water from tank;
sponge remaining
water from
bowl before
removing toilet.
Clean Flange
!Caution: If leaving floor flange
open for more than 1-2 hours,
cover flange to prevent escaping
sewer gases.
BACK-TO-BACK INSTALLATION
Recommended fitting type for
back-to-back installations.
Depending upon your plumbing and venting conditions, the flow from the
toilet in a back-to-back installation may create a vacuum on the system
and draw water from the opposing bowl. The National Standards Plumbing
Code prohibits the use of a cross fitting for drainage as throw over is
possible. The code does approve a directional "Y" style fitting with proper
venting to direct the water downward and away from the other toilet.
Press firmly.
1 2
Wax Ring Slow Close Toilet Seat
Water Supply Line
SOLD SEPARATELY
NOTE: T Bolts with retainer included. NOTE: Bowl with exposed trapway shown.
Wax Ring
(sold separately)
INSTALLATION INSTRUCTIONS:
BEFORE YOU START: Please see specificaton sheet for rough-in information
7302484-100R1 10/20
- 2 -
If Removing An Existing Toilet

!WARNING: Overtightening of water supply line nuts could result in breakage and potential flooding. If the
connection leaks after hand tightening, replace the supply line. Do not use any type of sealant on the water
supply connection. Use of plumber’s putty, pipe dope, or any other type of sealant will void the warranty.
5
7 8
6
Thread, then hand
tighten water supply. This
is best done when using
Concealed Trap Bowl.
Tighten handles
alternately until tank
contacts bowl.
HAND TIGHTEN
ONLY!
* For seat installation,
see instructions
included with seat.
7302484-100R1 10/20
- 3 -
34
TIP: Place 2 pieces of masking tape on floor
(as shown) to help with alignment in step 4. NOTE: Bowl with exposed
trapway shown.
NOTE: If installing a Concealed Trap Toilet Bowl,
connect supply hose to supply valve.
Apply weight evenly.
Do not move after
placement. Water
tight seal may break.
Hand tighten only.
Do not overtighten.
!
NOTE: Exposed trap shown.
Bolt caps not used for
Concealed Trap models.
MANUAL FLUSH
BUTTON

AA BATTERY PACK
Flush Control Module
7302484-100R1 10/20
- 4 -
Hand Sensor Module
Hand Sensor
LED Light
Flush Control
Cable Connector
Flush Control
Cable Connector
Manual Flush
Button / Assembly
Water Supply
Hose Nut
Flush Valve
In-Line Filter
Flush Control
Tower
Rell Tube / Overow
Flush Control Cable
Water Lever
Adjustment Screw
AA Battery Pack

7302484-100R1 10/20
- 5 -
9
10
Hand Sensor Module
a. Remove plastic Flush Control Module/Battery Pack
Clip from box, snap and place over “Flush Valve
In-Line Filter” area.
b. Remove Flush Control Module/Battery Pack from box
and follow procedure in “Operational Guide”, steps 4 to 9
under “Changing Batteries / Flush Control Module in
Tank to add batteries to module. (ref illustration from
attached drawing)
Remove Hand Sensor Module from box and follow procedure
in “Operational Guide”, steps 1 to 3 under “Changing
Batteries / Hand Sensor Module”, while also referencing the
NOTES portion at the end.
Also reference under the “Operational Guide”, “Installation of
Hand Sensor Module”, for preferable locations to mount the
Hand Sensor Module.
Please utilize the included signage should you feel it
necessary to communicate to users how to activate the
hygienic touchless ush. The signage can be affixed to the
top of the tank or around the ush actuator.
Example: around the ushing actuator on wall
Example: on tank cover
Flush Control
Module/Battery
Pack Clip
Flush Control
Module/Battery
Pack