Llampec 24 Instruction manual

QUICK USER’S

GUIDE

MODELS

24-24S-26S-40 & 40S

YOUR ENERGISER

WELCOME

First of all, thank you for purchasing our product.

Before using it for the first time, please read this quick guide carefully.

This energiser, like all LLAMPEC products, has been manufactured under

the strictest quality controls and developed with the utmost care.

The technology used in our devices allows them to preserve their effi-

ciency even in the case of voltage losses.

In addition to this, they are sealed with special high-quality resins to

prevent moisture, dust, water or small insects from damaging the device.

This ensures that, on the one hand, they can remain in perfect working

order outdoors and, on the other hand, increases their service life.

CONTENTS

04 YOUR ENERGISER

07 START-UP

09 OTHER INDICATIONS

• FUNCTIONING OF THE VOLTMETER

• HOW TO RECHARGE THE BATTERY

• HOW TO CHANGE THE 12V BATTERY

• HOW TO CHANGE THE FUSE

• HOW TO INSTALL A SOLAR PANEL

16 WARNINGS AND RECOMMENDATIONS

17 SOLVING COMMON PROBLEMS

17 BOX INCLUDES

18 TECHNICAL SPECIFICATIONS

20 WARRANTY TERMS AND CONDITIONS

YOUR ENERGISER

INITIAL CONTACT

The energisers Model 24, 24S, 26S, 40 & 40S have 2 front panels located at each end:

Panel A

( Output Panel ) Panel B

( Control Panel )

Panel A also known as “Output Panel” : this is the part where the energiser is connected to the

fence and to the ground.

Panel B also known as “Control Panel” : this is the part where the on/off button and the speed

button are located.

PANEL A ELEMENTS

( 1 ) Impulse indicator: It lights up whenever the energiser gives a voltage impulse to the fence,

thus verifying its operation.

( 2 ) Socket connectors: Used to connect the energiser to the fence and to grounding system.

TOMA

TIERRA CICLOS

IMPULSOS CERCA

LINEA

10.000-Volt.

( 2 )

( 1 )

VOLTAGE BATERÍA

II-Oi

I-OF

OFF

CONECTOR

PANEL SOLAR

12V.

CONECTOR

CARGADOR 230V.

( 1 )

(2)

(3)

(4)

PANEL B ELEMENTS

Speed switch to select the pulse intervals (remember that the output power will always be the

same, the only thing that will vary is the frequency of the pulse interval).

(2)

( 1 )

Digital voltmeter: Indicates the battery status as long as the energiser is operating (is when

the on/off switch is in the “ON” position).

On the other hand, it is recommended to recharge the battery before the voltmeter indica-

tes 8V, as when the battery is below 7V, the energiser will automatically switch off so as

not to damage the battery.

(3)

(4)

NOTE:NOTE: To get a true reading of the voltmeter, it is recommended to disconnect the energiser from the mains and waitTo get a true reading of the voltmeter, it is recommended to disconnect the energiser from the mains and wait

a few seconds.a few seconds.

Jack connector for solar panel and charger 230V.

Power switch for Turn ON (1 ON position) Turn OFF (0 OFF position) to

start and stop the energiser.

NOTE: On the 24 model, when the energiser is plugged into the mains to recharge the battery, it will conti-

nue to operate as long as the on/off switch is in the “ON” position.

PANEL B ELEMENTS

MODEL 40 & 40S

VOLTAGE BATERÍA

AUTO

MANUAL

SENSOR

CREPUSCULAR 12V.

( 1 ) (2)

(3)

(4)

(5)

( 1 ) Selector:

- High position (-) MANUAL Switch position. Starts the energiser, independent of sunlight.

- Position (0) Middle position of the selector, total shutdown of the energiser.

- Low position (=) AUTO (*) In this position the energiser will start automatically at night

and stop at sunrise.

(2) Speed switch: To select the pulse intervals (remember that the output power will always be

the same, the only thing that will vary is the frequency of the pulse interval). It works in both

(-) MANUAL and (=) AUTO positions.

(3) Digital voltmeter: Indicates the status of the battery as long as the energiser is running (the

selector must be in the (-) MANUAL or (=) AUTO position).

On the other hand, it is recommended to recharge the battery before the voltmeter indicates

8V. When the battery is below 7V, the energiser will switch off automatically so as not to

damage the battery. Even if you can see the voltmeter below 7V, the battery will never go

below 7V.

(4) 12V connector base: Jack for solar panel.

(5) Twilight Sensor: An automatic switch to activate the energiser when the natural light dims

and it becomes dark.

NOTE: When the selector (1) is set to position (=) AUTO runs for 5 seconds. If there is sufficient sunlight it will switch

off. Otherwise it will continue to run.

For stop, it also needs a few seconds to be able to change the status.

START-UP

CONNECT THE ENERGISER TO THE

FENCE AND GROUNDING SYSTEM

STEP 1. Go to Panel A (“Exit Panel”).

STEP 2. Connect the positive wire (red banana) to the red socket “CERCA LINEA”.

STEP 3. Connect the negative wire (black banana) to the black socket “TOMA TIERRA”.

STEP 4. Connect the terminal on the other end of the black wire to the grounding system and the spring-clip

on the red wire to any point on the positive wires of the fence.

TOMA

TIERRA CICLOS

IMPULSOS CERCA

LINEA

10.000-Volt.

TOMA

TIERRA CICLOS

IMPULSOS CERCA

LINEA

10.000-Volt.

TOMA

TIERRA CICLOS

IMPULSOS CERCA

LINEA

10.000-Volt.

TURN ON THE ENERGISER

STEP 1. Go to the on/off switch located on Panel

B (“Control Panel”).

Energisers MOD.24,24S AND 26S

STEP 2. Turn the on/off switch to the “ON” position.

Energisers MOD.24,24S AND 26S

STEP 3. The speed switch (“I or II”) is used to select the pulse intervals (time between pulses) where

position I is slow and position II is fast.

NOTE:NOTE: In both position I and position II, the output power is the same, the only thing that varies is the frequency of the range.In both position I and position II, the output power is the same, the only thing that varies is the frequency of the range.

STEP1. Go to the Selector switch located on Panel B

(“Control Panel”).

Energisers MOD.40 and 40S

AUTO

MANUAL

AUTO

MANUAL

STEP 2. Set the Selector switch to the “MANUAL” posi-

tion. Energisers MOD.40 and 40S

* Set the Selector switch to the “AUTO” position so

that the energiser operates only at night. Energisers

MOD.40 and 40S

OTHER INDICATIONS

DIGITAL VOLTMETER OPERATION

1The voltmeter is activated when the on/off switch is in the

“ON” position.

switch is in the “ON” position,

marking the actual battery status.

When the voltmeter (when disconnected from the mains)

shows 12V, the battery is 100% charged.

3Before the voltmeter reaches 8V, it is recommended to recharge the

battery, as once it drops below 7V, the energiser will automatically

switch off to prevent battery deterioration.

NOTE: If on any occasion the voltmeter shows a voltage lower than 7V, this does NOT mean that the energiser is faulty.

HOW TO RECHARGE THE BATTERY

MODEL 24, 24S AND 26S

1Go to Panel B (Control Panel) of your

energiser.

Next, connect the jack end of the charger

to the 12V. connector on the control

panel.

3Finally, plug the charger into a 230V

mains socket.

NOTE:NOTE: To recharge the battery, it does not matter what position the on/off switch is in.To recharge the battery, it does not matter what position the on/off switch is in.

However, if the energiser is switched on, the voltage on the voltmeter will increase by a few volts instantly.However, if the energiser is switched on, the voltage on the voltmeter will increase by a few volts instantly.

Therefore, to know the actual voltage, it is recommended to unplug the energiser from the mains, turn the on/off switch to theTherefore, to know the actual voltage, it is recommended to unplug the energiser from the mains, turn the on/off switch to the

“ON” position and wait a few seconds for the actual reading to be displayed.“ON” position and wait a few seconds for the actual reading to be displayed.

CONECTOR

PANEL SOLAR

12V.

CONECTOR

CARGADOR 230V.

12V.

CONECTOR

PANELSOLAR

CONECTOR

CARGADOR 230V.

NOTE:NOTE: The energiser model 26S does not include the charger, so in order to recharge the battery without a solar panel, itThe energiser model 26S does not include the charger, so in order to recharge the battery without a solar panel, it