Lockly ACCESS TOUCH User manual

3D FINGERPRINT SCANNER FOR DEADBOLTS
INSTALLATION GUIDE
ACCESS TOUCH

Go to Lockly.com/installation to watch a video
version of this installation guide.

Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to
install and get your Lockly up and running.
Installation generally takes less than 30 minutes. If
you have any questions please reference our online
support at: Lockly.com/support or call [phone]
for help.

You will need the following tools:
*Modify door hole using a wood file or utility knife. When trimming the door hole, make
sure to have enough space for the fingerprint sensor cable. Avoid cable from getting
pinched or tightly squeezed between the door surface and lock's ring or shield.
3
Required Tools
Important, before getting started...
Phillips Screwdriver
*Optional
Flathead Screwdriver Wood File
Lockly Access Touch is designed to work with existing standard deadbolts. Before
installing, check your existing deadbolt for smooth and clean operation. With the
door closed, the deadbolt should lock and unlock without any resistance or binding.
If any resistance or binding exist, adjust or modify strike plate for smooth, resistance
free operation. Failure to do so will impede the performance of the Lockly Access
Touch.
If needed, Lockly offers standard mechanical deadbolts designed to work with
Lockly Access Touch to replace old or worn deadbolts. To purchase, visit
www.lockly.com/accessories or call our Customer Hotline: [phone].

Remove the existing lock installed on your door and retain the deadbolt.
*Modify door hole using a wood file or utility knife. When trimming the door hole, make
sure to have enough space for the fingerprint sensor cable. Avoid cable from getting
pinched or tightly squeezed between the door surface and lock's ring or shield.
4
Step 1
Existing Deadbolt
1
REMOVE EXISTING DEADBOLT

A. NO RING B. MOUNTING RING C. ANTI-PRY SHIELD
Does not require door
lock hole modification.
There are primarily 3 different styles of deadbolts (shown below) found on most doors.
Depending on which type yours is, you may need to do a slight modification on your door
hole (trim by wood file or utility knife) to ensure the cable of the fingerprint sensor is
not pinched between the door and the lock.
*Optional
5
Step 1 continued
Door Exterior
2
REMOVE EXISTING DEADBOLT
Lock type B and C require door hole
modification. File or trim door hole to
avoid cable from being pinched .
IMPORTANT:

6
Step 2
2
Front/Exterior
With the mounting plate facing out,
route the cable on the fingerprint
sensor through the deadbolt
hole as shown.
Square Mounting Plate
Round Mounting Plate
Depending on the style and shape of your existing deadbolt, select either the square
or round , provided mounting plate.
A
A
B
B
C
C
DEMO
1
60mm
70mm
Standard diameter of
rounded deadbolt lock
INSTALLING FINGERPRINT SENSOR
Adjust the position of the sensor according to
the diameter of your deadbolt lock.
Carefully tighten screws after adjusting the position.
D
D
D

7
Door Exterior
CABLE UNDER
DEADBOLT BODY
!
Existing
Deadbolt
Guide the cable through the door
hole under the existing deadbolt.
Remove protective paper from adhesive
strips.
Carefully check alignment then press
mounting plate and sensor flush to door.
Remove positioning sleeve, assembly
should remain in place by the adhesive
strips.
Insert the Positioning Sleeve
INSTALLING FINGERPRINT SENSOR
Open area positioned at the bottom
* If you trimmed or filed your door hole, the cable
should be seating on the trimmed or filed area.
E
E
6
34
5
Step 2 continued
IMPORTANT:

8
Step 3
Make sure the deadbolt is extended If necessary, remove key from deadbolt .
Check to make sure the deadbolt remains
fully extended. If needed, use a screwdriver
or pliers to fully extend.
Reinstall deadbolt ensuring torque blade
and lock are in the correct orientation.
INSTALLING THE EXTERIOR ASSEMBLY
II
II
I
I
V
V
12
34
II I

9
Step 4 INSTALLING THE INTERIOR ASSEMBLY
1
Identify and select the appropriate
spindle/torque blade adapter that
matches your lock.
Silver
Gold ---- Right Swing Doors
Black ---- Left Swing Door
Red
Green
Attached the temporary positioning
guide tool to the selected adapter
to form the adapter assembly. You will
use the adapter in the succeeding steps.
Adapter Assembly
H
K
Z
HK
2
If none of the provided adapters match your locks spindle or torque
blade, please call our Customer Hotline [phone] to get help with
an alternative solution.
IMPORTANT:

10
INSTALLING THE INTERIOR ASSEMBLY
Step 4 continued
Attach the adapter assembly to the
torque blade or spindle. Ensure assembly
mated with the torque blade or spindle
and it is level with the lock and the mount-
ing plate. Check alignment of the mount-
ing plate before securing it with adhesives.
34
Z
Z
G
Secure the rubber gasket to the interior
mounting plate. Route the sensor cable
through the notched rectangular hole
located at the bottom of the mounting
plate .
F
F

11
6
5
Insert and hand tighten backplate screws. Adjust alignment as needed and tighten with
a screwdriver until mounting plate is secure.
Remove the adapter and positioning tool assembly.
INSTALLING THE INTERIOR ASSEMBLY
Step 4 continued
N
N
*Use the existing screws of your deabolt.
Make sure the screw head will not pass
through the mounting plate holes. Use
provided washer if the screw head is
less than <9mm.

NOTE: Positioning tool must be removed.
12
78
Step 4 continued
INSTALLING THE INTERIOR ASSEMBLY
Using the key for your deadbolt, test
locking and unlocking to ensure smooth
operation. If there is binding or resistance,
loosen the back plate mounting screws
and adjust plate alignment with spindle
/torque blade to alleviate any misalign-
ment that may be causing the issue
Remove positioning tool and return
adapter to torque blade or spindle
V
V
III
K
K
H
H
When finish, leave the deadbolt fully extended and remove the key if
necessary before proceeding to the next step.
IMPORTANT:

13
Step 4 continued
INSTALLING THE INTERIOR ASSEMBLY
Push any excess cable that might
interfere with the back assembly
or the spindle/torque blade back
through the deadbolt door hole.
NOTE: If you need to disconnect the
cable, make sure to press the snap tab
to release the plug before carefully
pulling it out. Do not force, as this may
result in damaging the lock.
Plug the cable coming through mounting plate into the interior assembly as shown.
Tuck cable under eyelet hook and route to the right on interior assembly
Plug into , match red side of
plug with red on socket - insert tightly.
XY
X
Y
9

14
Step 4 continued
INSTALLING THE INTERIOR ASSEMBLY
Before placing the interior
assembly onto the mounting
plate, ensure the thumb turn
is vertical.
Merge the interior assembly to
the mounting plate ensuring the
spindle torque/blade adapter
seats properly to the thumb
lever receiver. You may need
to wiggle the thumb lever back
and forth slightly in the process
to align the two parts. Secure the interior assembly
to mounting plate with 2
screws.
M
2X
M
RESET
PROGRAM
L
L
12
11
10

15
After all batteries are installed, PRESS and HOLD the program button for 10S. The lock
will automatically start self-check (release program button once check starts). The
self-check process determines right or left swinging door and is very important to
ensure correct installation. IMPORTANT: If lock is not properly installed it will open and
close repeatedly (refer to next page #3).
With door open and deadbolt fully extended, place ribbon inside compartment and
insert 8batteries (note correct -/+ polarity).
123
4
PRESS
& HOLD
123
4
1
2
Step 5 INSTALLING BATTERIES

16
If your lock is not properly installed, it will open and close repeatedly at times
and/or battery life will be reduced.
Once self-check completes ensure the lock operates smoothly by manually locking
and unlocking the door using the thumb turn on the interior assembly. The deadbolt
should operate smoothly without any interference or binding. If necessary, repeat
steps 3 & 4 and ensure that (a) the deadbolt was extended and (b) The spindle/torque
blade was properly mated and aligned to the interior back assembly.
Once self-check is complete, install battery cover , secure with screw on top (do
not over tighten).
INSTALLING BATTERIES
J
J
3
4
5 6 7 8
Step 5 continued
IMPORTANT:

17
Step 6 DOWNLOAD LOCKLY APP
Congratulations! You have completed the Lockly Access Touch installation. To complete its setup,
download the Lockly App from the App Store or on Google Play and follow on-screen instructions
for adding a new lock.
Scan or visit
Lockly.com/app
or
Search & Download
Directly on...

FCC Warning：
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must acceptany interference received, including interference
that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should
be installed and operated with minimum distance 20cm between the radiator & your body.
IC WARNING
This device contains license-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
IC Radiation Exposure Statement
This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and
operated with a minimum distance of 20cm between the radiator and any part of your body.
Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de lanorme RSS-102. Il doit
être installé et utilisé à une distance minimale de 20 cm entre le radiateur et toute partie de votre corps.
WARNING: This product can expose you to chemicals including Lead, which is known to the State of California
to cause cancer. For more information go to www.P65Wamings.ca.gov.

Lockly Access Touch can be fitted for both right swing doors and left swing doors.
INSTALLATION OVERVIEW AND PARTS LIST
SCAN & SAVE
LOCK SERIAL
ACTIVATION CODE
PGDXXXXXXXXXXXXXXXX
XXXXXXXX
Positioning Sleeve
Parts List
Labeled As Description
ASquare Mounting Plate
Parts List (Not Included)
Labeled As Description
BRound Mounting Plate
CFingerprint Sensor
DKM3*6mm Screw
E
Positioning Tool
Interior Mounting Plate
Adhesive Strips
F
G
H
JBattery Cover
KAdapter
LInterior Assembly
MPM4*12mm Screw
UActivation Card
ZAdapter Assembly
NWasher
V
D
U
II
F
N
G
III
H
Z
K
L
M
J
Keys
ILock Exterior
II Deadbolt
III Screws
V
B
A
C
I
E
ACC20211201