Loepfe MillMaster TOP User manual
Installation Manual
MillMaster® TOP
46943003_en
Original Manual
Version 1.0 / 04.2019
Loepfe Brothers Ltd.
Kastellstrasse 10
8623 Wetzikon / Switzerland
Phone +41 43 488 11 11
Fax +41 43 488 11 00
E-mail [email protected]
Internet www.loepfe.com
Document title: MillMaster TOP Installation Manual
Language version: English
This Manual is protected by copyright.
Complete or partial reproduction and dissemination of this Manual to third parties – even in form of extracts –
as well as the use and / or disclosure of the contents are not allowed without the written approval of Loepfe
Brothers Ltd., except for internal purposes.
MillMaster is a registered trademark of Loepfe Brothers Ltd. in Switzerland and / or in other countries.
© 2019 Loepfe Brothers Ltd., Switzerland
MillMaster TOP www.loepfe.com 3
Contents
Contents
1 General Information 7
1.1 About this document 7
1.2 Scope of application 7
1.3 Target audience 7
1.4 Notes 7
2 Safety 8
2.1 Intended use 8
2.2 Safety Information and Warnings 8
2.3 Explanation of symbols 8
3 Installation 9
3.1 System requirements 9
3.2 Network topology 11
3.2.1 Network with one IP address 11
3.2.2 Network with multiple IP addresses 12
3.2.3 Network via routers 13
3.2.4 Network with VPN 14
3.3 Configuring central units and connecting them to the network 15
3.3.1 IP addresses 15
3.3.2 LZE-V 16
3.3.3 LZE-III 18
3.3.4 LZE-II 20
3.3.5 Schlafhorst Informator AC5/ACX5/AC6 23
3.3.6 Schlafhorst Informator AC338 26
3.3.7 Schlafhorst Informator with series number < 7000 26
3.3.8 Schlafhorst Informator with series number > 7000 30
3.4 Connect local network and test connection 32
3.5 Configure server 34
3.5.1 Change BIOS settings 34
3.5.2 Change server name 34
3.5.3 Change network connection properties 35
3.6 Install MillMaster TOP software 38
3.6.1 Installation requirements 38
3.6.2 Installation 38
3.6.3 Install additional client computers 40
3.6.4 Install MillMaster TOP Client 41
4 Operation 42
4.1 System startup 42
4.1.1 Start and configure software 42
4.1.2 Configure MillMaster (TOP server) 42
4.1.3 Activate licenses and options 43
4.1.4 Add user 44
MillMaster TOP www.loepfe.com 5
General Information
MillMaster TOP www.loepfe.com 7
1 General Information
1.1 About this document
This Instruction Manual helps users to work safely and efficiently with MillMaster TOP.
Read this Instruction Manual in its entirety before starting up MillMaster TOP.
This manual is part of MillMaster TOP and must be kept accessible to trained operators at all times in the
immediate vicinity of the device.
1.2 Scope of application
This document applies to:
The MillMaster TOP software tool.
1.3 Target audience
This document is intended for use by specialist personnel only. The descriptions given here assume that
the reader is a qualified professional trained by the manufacturer. These descriptions do not replace
training on product use.
1.4 Notes
Information symbol
This symbol indicates additional information for the user.
Images in the document
The images of the user interface (screenshots) included in this manual are examples,
and do not necessarily contain relevant data.
Safety
8 www.loepfe.com MillMaster TOP
2 Safety
2.1 Intended use
This software is intended exclusively for use as a data analysis and administration tool for yarn clearers
that are linked to the central units of the spinning machines. Any other use, or any use that goes beyond
the intended purpose, is considered improper. Loepfe Brothers Ltd. shall not be liable for any damages
that result from improper use.
2.2 Safety Information and Warnings
Safety information and warnings draw attention to hazards and are marked with symbols and signal words
to express the danger level.
DANGER
Indicates an immediate hazardous situation which will result in death or serious
injury.
WARNING
Indicates a potentially hazardous situation which could result in death or serious
injury.
CAUTION
Indicates a potentially hazardous situation which may result in minor oder
moderate injury.
NOTE
Indicates a potentially hazardous situation which may result in damage to
property.
2.3 Explanation of symbols
Warning symbol
General warning symbol
Electrical voltage warning
Installation
MillMaster TOP www.loepfe.com 9
3 Installation
3.1 System requirements
Server
64-bit operating system Windows 10
Windows in English version or with Multilingual User In-
terface (MUI) package recommended
Processor Intel Core i5, ≥ 4th Gen; recommended i7*, ≥ 4th Gen
Working memory ≥ 16 GB RAM
Disk storage ≥ 500 GB SSD
Network connection (Ethernet) LAN 100/1000 Mbit/s
Ports USB
Uninterruptible power supply (UPS) recommended
Monitor min. 24 inches
Monitor resolution min. 1366 x 768
Client computers
64-bit operating system Windows 10
Processor Intel Core i5, ≥ 4th Gen
Working memory ≥ 8 GB RAM
Disk storage ≥ 250 GB HDD
Network connection (Ethernet) LAN 100/1000 Mbit/s
Ports USB
Monitor (diagonal) min. 24 inches
Monitor resolution min. 1366 x 768
Installation
10 www.loepfe.com MillMaster TOP
Software (required)
.NET Framework 4.X.X If not already installed, this software will be installed dur-
ing the installation.
PostgreSQL If not already installed, this software will be installed dur-
ing the installation.
Internet Explorer 11
GoToAssist
Mobile devices (optional) Recommended browsers
Smartphones and tablets – Firefox ≥ 35.0
– Internet Explorer ≥ 9.0
– Safari ≥ 8.0
– Google Chrome ≥ 42.0
– Chromium ≥ 44.0
– Opera ≥ 25.0
Network connection
Ethernet cable Do not use unshielded UTP cables!
Cat5e, shielded, STP ***
Cat6a, shielded, STP ***
Cat7*, shielded, STP ***
Length ≤ 100 m
Switch max. 4
Patch cable Cat6a, shielded, STP ***
Length ≤ 10 m
Switch 1000 Mbit/s (Gigabit Ethernet Switch)
Router (optional) 1000 Mbit/s (Gigabit Ethernet Router)
Internet Constant connection
Support
Ports reachable:
TCP: 80, 443, 8200
UDP: 53, 514, 1853, 8200
Legend
* We recommend this version.
** We recommend that you install the English version of
the operating system so that the Technical Support team
can change the language settings in case support is
needed.
*** compliant with IEEE 803.3, EN 50288-2-1:2013
Installation
MillMaster TOP www.loepfe.com 11
3.2 Network topology
This section presents examples of network connections.
To ensure proper and error-free network connections, only “shielded” (STP) cables
should be used.
3.2.1 Network with one IP address
Installation
12 www.loepfe.com MillMaster TOP
3.2.2 Network with multiple IP addresses
The machine network and the client network are connected by means of a connection between the two
switches. A static IP address is required for a connection from the software via VNC.
Installation
MillMaster TOP www.loepfe.com 13
3.2.3 Network via routers
The machine network and the client network are connected via routers.
Installation
14 www.loepfe.com MillMaster TOP
3.2.4 Network with VPN
The machine network and the client network are connected via VPN through two routers. This type of
connection is used when two separate networks need to be connected to one another.
Installation
MillMaster TOP www.loepfe.com 15
3.3 Configuring central units and connecting them to the
network
This section describes the different connections to the network and the associated configurations for the
central units.
The software can be connected to the following central units and Informator units:
nCentral unit: LZE-I, LZE-II, LZE-III and LZE-V
nMachine type: Schlafhorst AC 338 and Schlafhorst Oerlikon AC5, ACX5 and AC6 Informators
Requirements for configuration and network connection
nRJ45 cables are available.
nPlan at least 0.5 meters (1 foot 8 inches) of additional RJ45 cable length.
nRJ45 cables are laid in a cable tray or other appropriate device.
nRJ45 cables are not laid together with cables that carry a live voltage.
3.3.1 IP addresses
This section provides suggestions and examples of IP addresses and subnet masks that can be used to
connect the winding machines.
No. Machine
name
IP
addresses
Subnet mask Host
name
LZE
type
Yarn
clearer
type
Spindle
PC MillMaster 192.168.7.1 255.255.255.0
01 Winding ma-
chine 1
192.168.7.101 255.255.255.0
02 Winding ma-
chine 2
192.168.7.102 255.255.255.0
Notes:
Table1:
Example IP addresses and subnet masks
The following local IP address ranges are also available; these ranges are not reachable on the Internet
and can therefore be used for the software.
IP addresses
10.0.0.0 – 10.255.255.255
172.16.0.0 – 172.31.255.255
192.168.0.0 – 192.168.255.255
Table2:
Examples of additional IP addresses
Installation
16 www.loepfe.com MillMaster TOP
3.3.2 LZE-V
Connect the LZE-V to the client computer
DANGER
Danger of electric shock
Touching live components and electrical connections can lead to severe injury or
death.
4Unplug the device from mains power before performing any repair or
maintenance work.
4Unplug the device from mains power before removing device enclosure or
opening side panels.
üUse the IP address 192.168.1.200 as the default.
1. Connect the client computer to the LAN 2 port with an RJ45 cable.
ðThe software is now connected to the LZE-V central unit.
LZE-V rear panel
Configure network settings
Prerequisites
üThe LZE-V has been started up.
1. Open Settings > Machine > Base settings.
2. Press .
ðThe login window opens.
3. Enter username (Foreman) and password.
4. Press to edit settings.
5. Machine Name: Enter the name of the machine.
6. MillMaster Link: Select “On”.
7. Confirm with .
ðThe settings are saved.
Installation
MillMaster TOP www.loepfe.com 17
Please note the following restrictions for the hostname:
nuse 8 characters max, no spaces
nUse the letters A-Z, a-z and digits 1-9
nThe first character must be a letter
nHostname and machine name can be identical
1. Open Service > Setup > Network.
2. Press .
ðThe login window opens.
3. Enter username (Service) and password.
4. Press to edit settings.
5. Select the «Network» tab.
6. Host Name: Enter the hostname, e.g. MA01.
7. Select the «LAN 2» tab.
8. DHCP: Select “Off”.
9. IP Address: Enter the IP address.
10. Subnet Mask: Enter the subnet mask, e.g. a value from the IP addresses [}15] table.
11. Gateway: Enter the gateway IP address.
12. DNS: Enter the DNS IP address.
13. «LAN 1» tab: Do not make any changes, except for SAVIO machines.
14. Confirm with .
ðThe settings are saved.
ðThe software restarts.
Service > Setup > Network settings
Installation
18 www.loepfe.com MillMaster TOP
3.3.3 LZE-III
Connect the LZE-III to the client computer
1. Connect the client computer to the LAN 1 port with an RJ45 cable.
2. Select the «Dialog» tab.
3. Select the Software > Options menu.
ðThe «Reports» window opens.
4. Find the MAC address under «Reports».
5. Find the MAC address in the Central unit menu and compare with the MAC address from Reports.
ðIf MAC Address 1 matches, for example, then the LAN 1 port is activated.
ðThe software is now connected to the LZE-III central unit.
LZE-III rear panel
Configure network settings
Prerequisites
üThe LZE-III has been started up.
1. Select the «Dialog» tab.
2. In the Permissions menu, select Foreman Password.
Installation
MillMaster TOP www.loepfe.com 19
ðThe Permissions window opens.
3. Enter the foreman password.
4. Press «OK».
ðThe user level / password level is set to Foreman and the menu changes.
5. Check the MAC address, and change the MAC address if needed. See the section on how to
Connect the LZE-III to the client computer.
6. Select «Reboot system».
ðA “Reboot system?” pop-up window appears.
7. Press «Yes».
ðThe system restarts.
ðThe «System monitor for LZE» window opens.
1. Press «To start service screen» to change the IP address.
ðThe «Loepfe YM Zenit monitor service screen» window opens.
2. Press «Change IP Address».
ðA confirmation window appears.
3. Press «Yes» to reboot the system.
ðThe system restarts.
ðThe «SetIpAddrXp» window opens.
4. Under New Settings, go to the “LAN Adapter to change” field and select LAN 0 or LAN 1.
5. In the “Address Mode for LAN” field, select the radio button for “Use static IP address”.
6. In the “Static IP Address for LAN” field, enter the machine’s current IP address, e.g. from the IP
addresses [}15] table.
7. Press «Set new settings and reboot» to reboot the system.
ðThe settings are saved.
ðThe system restarts.
ðThe network settings are configured.
Installation
20 www.loepfe.com MillMaster TOP
SetIpAddrXp
3.3.4 LZE-II
Connect Ethernet cable
Prerequisites
üThe LZE-II has been started up and the menu has been opened.
1. Connect an RJ45 cable to LAN 1 to use the software.
ðThe software is now connected to the LZE-II central unit.
LZE-II rear panel
Configure network settings (version ≥ 2.0)
1. Select the «Dialog» tab.
2. In the Permissions menu, select Foreman Password.
ðThe Permissions window opens.
Table of contents
