LOGAIRE FIRES MAUI User manual

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 1
INSTALLATION AND OPERATING
INSTRUCTIONS
MAUI GAS FIRES
FREESTANDER AND INBUILT
NATURAL GAS / LPG HEATER
LOGAIRE FIRES
S A F E T Y W I T H S T Y L E
To find out more call our home heating hotline [phone]
Manufactured by and all material ©to Metal Fab Industries Ltd. Specifications are subject to change,
however at the time of printing every effort has been made to ensure this information is correct.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING: If the information in these instructions are not followed exactly, a
fire or explosion may result causing property damage, personal damage or loss
of life.
• Do not store or use gasoline or other flammable vapours and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbour’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
• Installation must be performed by a qualified installer, service agency or the gas
supplier.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 2
TABLE OF CONTENTS
TO THE NEW OWNER 4
LOGAIRE MAUI 5
Safety Instructions 5
What To Do If You Smell Gas 5
Lighting Instructions 6
To Turn Off Gas Appliance 6
Manufacturer’s Installation & Operation Instructions 7
OPERATION 8
Operating Instructions 8
Lighting Procedure 9
Initial Burning 10
Heat Output Adjustment 10
Automatic Convection Air Fan Operation 10
Shutdown Procedure 10
SPECIFICATIONS 11
Listings and Code Approvals 11
Logaire Maui Inbuilt/Freestander 12
INSTALLATION 13
General Information 13
Clearance To Combustibles – Freestander 14
Clearance To Combustibles – Inbuilt 15
Minimum Fireplace Dimensions 16
Venting 17
Freestander 17
Model Inbuilt 17
Installation Into Exisitng Woodstove/Solid Fuel Flue System 17
Venting Requirements 18
Gas Connection 19
Natural Gas or LPG 19
Fascia And Assembly – Inbuilt 20
Gas Consumption By Gas Lab New Zealand 21
Gas Pressure Test 21
Primary Air Shutter 21
Test For Flue Exhaust Spillage – Freestander 22
Test For Flue Spillage – Inbuilt 23
Optional Wall Thermostat Installation 24
Optional Remote Control 24
Electrical Grounding Instructions 24
Optional Wall Thermostat Installation Diagram 25
Log Set Installation 26
Installation Technical Data 27
Installation Technical Data 28
Log Diagram 29
LPG Conversion Installation 30
MAUI ZERO CLEARANCE 31
General Description 31
Installation Notes & Safety 31
Required Components 31
Assembly Instructions 32
Optional Fresh Air Supply 33
Gas Supply Line 33
Installation of Maui 33
Framing 34
Placement And Finishing 34
Venting 34
Wiring 35
Clearance Shell Diagram 16 36
Diagram 17 & 18 37

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 3
TABLE OF CONTENTS Continued
Diagram 19 & 25 38
Zero Clearance Vertical Direct Vent Gas Flue Kit 39-40
MAUI ZERO CLEARANCE 41
Maintenance Instructions 41
Pilot Light 41
Log Replacement 41
Gold Plated Doors 42
Door Gasket and Glass Gasket 42
Removal and Placement of Broken Door Glass 42
Fan Maintenance 42
GAS TROUBLE SHOOTING GUIDE 43
Combustion 43
Requirements for Combustion 43
Heat Sources and Temperatures 43
Ignition Temperatures 43
Checking Wire Connections 44
Logaire Gas Stove Wiring Diagram 22 44
Checking Thermopile 45
Pilot Instructions 46
When the Pilot wont stay Lit 47
Adjust of the Piolet Flame 47
Robertshaw Valve Check – Millivolt Saftey Magnet 48
Checking Gas Pressure with a Monometer 49
WARRANTY 50
QUALITY ASSURANCE 50
WARRANTY FORM 51

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 4
To The New Owner:
Congratulations! You are the owner of a State-Of -The-Art gas stove by
Logaire. This appliance has been designed to provide you with all the
warmth and charm of a woodstove, at the flick of a switch. This model
has been approved by OMNI – test laboratories, inc. for both safety and
efficiency. As it also bears our own mark, it will provide you with
trouble-free economy, comfort and security for many years to follow. To
qualify for Logaire’s warranty program, be sure to fill out the registration
form included in the packet and drop it in the mail today! Please take a
moment now to acquaint yourself with these instructions and the many
features of your Logaire Maui gas stove.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 5
LOGAIRE MAUI
FOR YOUR SAFETY READ BEFORE LIGHTING
This appliance must be installed in accordance with local codes if any, if not,
follow the current CANI-B149/ANSI Z223.1-1988.
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life. Improper
installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Refer to the owner’s information manual provided with this
appliance. For assistance or additional information consult a qualified installer,
service agency or gas supplier.
A This appliance has a pilot which must be lighted by hand, following the
instructions below exactly.
B BEFORE LIGHTING smell all around the appliance area for gas. Be sure to
smell next to the floor because some gas is heavier than air and will settle to
the floor.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance
• DO NOT touch any electrical switch; Do not use any phone in your building
• IMMEDIATELY call your gas supplier from a neighbour’s phone. Follow
your gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department
C Use only your hand to push in or turn the gas control knob. Never use tools.
If the knob will not push in or turn by hand, don’t try to repair it, call a
qualified service technician. Force or attempted repair may result in a fire or
explosion.
D DO NOT use this appliance if any part has been under water. Immediately
call a qualified service technician to inspect the appliance and to replace any
part of the control system and any gas control which has been under water.
This appliance needs fresh air for safe operation and must be installed so there are
provisions for adequate combustion and ventilation air.
CAUTION: Hot while in operation. DO NOT TOUCH. Due to high surface
temperatures keep children, clothing and furniture away. Keep burner and control
compartment clean. See installation and operation instructions accompanying
appliance.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 6
LOGAIRE MAUI
LIGHTING INSTRUCTIONS STOP !
Read the safety information above this label
1 Push in gas control know slightly and turn clockwise to “OFF”. Knob cannot
be turned from “PILOT” to “OFF” unless knob is pushed in slightly.
DO NOT FORCE.
2 Wait five minutes to clear out any gas. If you then smell gas STOP! Follow
in the safety information above on this label. If you don’t smell gas, go to the
next step.
3 Turn know on gas control counterclockwise to “PILOT”.
4 Push in control knob all the way and hold in. Immediately push red button on
spark igniter until pilot lights. Continue to hold control knob in for about ½
minute after the pilot is lit. Release knob and it will pop back up. Pilot should
remain lit. If it goes out, repeat steps 3 and 4.
If knob does not pop up when released, stop immediately and call your service
technician or gas supplier. If the pilot will not stay lit after several tries, turn
gas control knob “OFF” and call your service technician or gas supplier.
5 Turn gas control knob counterclockwise to “ON”.
6 Use rocker switch to operate main burner.
TO TURN OFF GAS APPLIANCE
1 Push in the gas control knob slightly and turn clockwise to “OFF”.
DO NOT FORCE.
2 Turn off electric power to the appliance if service is to be performed.
Do not remove instruction plate: Logaire Maui F/S & I/B

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 7
LOGAIRE MAUI
LISTED: GAS FIRED VENTED FROOMHEATER – FREESTANDER AND
INBUILT.
TESTED TO : CAN 1-2.1-M86, ANSI Z21.11.1 – 1991
CERTIFIED FOR: CANADA AND U.S.A. REPORT NO. 476-1103
TESTED TO NZS5262:1997
GAS TYPE: NATURAL GAS OR UNIVERSAL LPG
(PROPANE/BUTANE)
GAS PRESSURE: NATURAL GAS – MAXIMUM SUPPLY
PRESSURE 5kPa
LPG – MAXIMUM SUPPLY PRESSURE 2.75kPa
BURNER PRESSURE: NATURAL GAS – 0.87 kPa LPG – 2.5kPa
INPUT RATING: 50MJ/h
INSTALL & USE ONLY IN ACCORDANCE WITH MANUFACTURER’S
INSTALLATION & OPERATION INSTRUCTIONS. FOR USE WITH NATURAL
GAS AND PROPANE. A CONVERSION KIT SUPPLIED BY THE
MANUFACTURER SHALL BE USED TO CONVERT THIS APPLIANCE TO
THE ALTERNATIVE FUEL.
GAS FIRED VENTED ROOM HEATER: THIS APPLIANCE MUST BE
INSTALLED IN ACCORDANCE WITH LOCAL CODES, IF ANY; IF NOT,
FOLLOW ANSI Z223.1 – CAN 1-B149.
ELECTRICAL SUPPLY 240V, .45 A, 50 Hz
NOT FOR USE WITH SOLID FUEL. DO NOT REMOVE LABEL.
METAL FAB INDUSTRIES; P O BOX 58 473
GREENMOUNT, AUCKLAND
FAX [phone]
Email: [email protected]
SERIAL NUMBER MG NO. _____________________

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 8
OPERATION
OPERATING INSTRUCTIONS
WARNING
Do not abuse the F/S or I/B’s glass by striking, slamming, or similar trauma. DO
NOT operate the stove with the glass panel removed cracked or broken. Use only
glass supplied by Logaire and approved for use with this heater. DO NOT use
substitute materials. Replacement of the panel should be done by a licensed or
qualified service person.
Before operating this appliance, proceed through the following checklist.
1. Read and understand these instructions before operating this appliance.
2. Check to see that all wiring is correct and enclosed to prevent possible shock.
3. Check to ensure there are no gas leaks.
4. Never operate the appliance with the door open.
5. Verify that all venting and the venting cap is unobstructed.
6. Verify that log placement is correct.
7. The unit should never be turned off and on without a minimum of a 60-second
wait.
8. Once pilot light is on, use the ON-OFF rocker switch for normal operation.
When off for more than a month, extinguish pilot by following shutdown
procedure. (For ON-OFF rocker switch location see page 10).
9. Keep area near the appliance clear and free from combustible materials,
gasoline and other flammable vapours and liquids.
DIAGRAM 1
DIAGRAM 2

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 9
OPERATION
LIGHTING PROCEDURE
1. STOP! Read the safety information. Pages 4 – 6.
2. If using an optional thermostat, set the thermostat to the lowest setting.
3. Turn off the electric power to the unit (unplug).
4. Turn the ON-OFF rocker switch to the OFF position. See page 10.
5. Push in the gas control knob slightly and turn it clockwise to “OFF”. NOTE:
The knob cannot be turned from “PILOT” to “OFF” unless it is pushed in
slightly. Do not force it.
6. Wait five (5) minutes to clear out any gas. If you smell gas, STOP! Follow
“B” in the safety information on the label on page 5.
7. Set the variable flame control to “HI” by turning it fully clockwise.
8. Press in the gas control knob slightly and turn counterclockwise to “PILOT”.
9. Find the pilot by looking under the middle of the front log.
10. Push the control knob fully down and hold. Immediately push the red piezo
igniter button to light the pilot. It is normal to have to push the red spark
igniter button several times before the pilot ignites. Continue to hold the
control knob in for about one (1) minute after the pilot is lit. Release the knob
and it will pop back up. Pilot should remain lit. If it goes out, repeat step 5
through 9.
• If the knob does not pop up when released, stop and immediately call
your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas control knob
to off and call your service technician or gas supplier.
11. Turn the gas control knob counterclockwise to “ON”.
12. Place the ON-OFF rocker switch to the ON position.
13. Turn on the electric power to the heater(Plug in).
14. If in use, set the optional thermostat to the desired room temperature.
15. Set the variable flame control to the desired setting; Turn fully clockwise for
“HI” and fully counterclockwise for “LOW”. See diagram 2. Refer to page 8.








 !"

#$  DIAGRAM 3
WARNING
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARD OF HIGH SURFACE TEMPERATURES AND
SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.
CAUTION: ANY SAFETY SCREEN OR GUARD REMOVED FOR SERVICING AN APPLIANCE MUST BE REPLACED
PRIOR TO OPERATING THE APPLIANCE.
CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 10
OPERATION
INITIAL BURNING
The first fire in your stove is part of the paint curing process. To ensure that the paint
is properly cured, light the unit and leave it on for 5 minutes and let it cool down for
30 minutes. Repeat 3 or 4 times. When first operated, the unit will release an odour
caused by the paint curing, the burning off of any oils remaining from manufacturing
and burning off the starch in the gas logs. Also the brick panels will discolour during
the initial burn and return to their original colour after about one hour. This is due to
the burning off of manufacturing starches.
The glass panel may require cleaning after the unit has cooled down. DO NOT
ATTEMPT TO CLEAN THE GLASS WHILE IT IS HOT.
HEAT OUTPUT ADJUSTMENT
The gas control valve, located behind the lower right access door, can be used to
adjust the heat output and flame height by turning the metal gas knob clockwise for
maximum and counter clockwise for minimum. (see diagram 1 page 8). The
minimum and maximum settings are factory set to provide a wide range of heat output
and should not be altered.
AUTOMATIC CONVECTION AIR FAN OPERATION
The fan control is located behind the lower left access door and is an “HIGH – OFF –
LOW” control. (see diagram 1 on page 8). The fan operates automatically when the
control is in the High or Low position. The fan will turn on as the stove comes up to
temperature. After the unit has been turned off and the stove has cooled to below a
useful heat output range the fan will shut off automatically.
SHUTDOWN PROCEDURE
1. Use the “ON-OFF” rocker switch to turn off the main burner.
2. To turn off pilot light, push in the gas control knob slightly and turn clockwise
to “OFF”. Do not force.
3. Turn off all electrical power to the appliance if service is to be performed.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 11
SPECIFICATIONS
LISTINGS AND CODE APPROVALS
The Maui Gas Heater has been tested to ANSI Z21.88a-1998 Vented Gas Fireplace
Heaters by OMNI – Test Laboratories, Inc. and listed for installation and operations
as described in these Installation and Operation Instructions.
This gas appliance has been tested in accordance with National Safety standards and
complies with the following.
AS / NZS 3350 . 1 : 2000, Gas Regulations : 1993
And NZS 5261 . 1 : 1996.
The installation must conform to local codes or in the absence of local codes with
NZS 5261 - 1996
Check with your local building code agency before you begin your installation to
ensure compliance with local code, including the need for “permits” and follow-up
inspections. If any problems are encountered regarding code approvals, or if you wish
clarification of any of the instructions contained here, contact your local dealer.
Your stove and venting system should be serviced annually by a qualified service
person.
Do not use this appliance if any part has been under water. Immediately call a
qualified service technician to inspect the appliance and to replace any part of
the control system and any gas control, which has been under water.
WARNING
Improper installation, adjustment, alteration, services or maintenance can cause injury
or property damage. Refer to this manual for assistance or additional information
consult a qualified installer, service agency or the gas supplier.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 12
SPECIFICATIONS
LOGAIRE MAUI INBUILT
LOGAIRE MAUI FREESTANDER

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 13
INSTALLATION
Installation and repair should be done by a qualified service person. The appliance
should be inspected before use and at least annually by a professional service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding
material, et cetera. It is imperative that control compartments, burners and circulation
air passageways of the appliance be kept clean.
Due to high temperatures, the appliance should be located out of traffic and away
from furniture and draperies.
WARNING
This appliance can only be common-vented in accordance with the Natural Gas
Installation Code. Which requires that the venting must be sized accordingly to
accommodate the total kW range of all appliances concerned and that the code allows
the venting of the appliances in question to be vented together. It should also be noted
that gas appliances must not be vented with solid fuel burning appliances,
WARNING
Failure to correctly install this appliance will void your warranty. For warranty
agreement refer to page 46.
General Information
Provide adequate clearance around the air openings into the combustion chamber. For
servicing and proper operation adequate combustion and ventilation air must also be
provided.
The Logaire Maui must be installed on a flat, solid, continuous surface (eg. metal,
concrete). This may be the floor, or it can be raised up on a platform to enhance its
visual impact. The Logaire Freestanding Gas Stove can be installed in a wide variety
of ways and will fit nearly any room layout. The Maui Gas Fire must be seismic
restrained through the holes provided.
The Logaire Freestanding Gas Stove is approved for alcove installations and must
meet the clearances listed. The freestanding and the fireplace insert can be installed in
a bedroom or bed/sitting room with a millivolt thermostat only. The inbuilt can be
installed in masonry or factory built fireplace. The freestanding and the fireplace
insert units are NOT approved for mobile home installations.
We recommend that you plan your installation on paper using exact measurements for
clearances and floor protection before actually installing this appliance. If an existing
chimney is not utilised, position the appliance to allow free passage of factory-built
listed chimney through the wall or ceiling and roof. Have a qualified building
inspector review your plans before installation.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 14
INSTALLATION
CLEARANCE TO COMBUSTIBLES – FREE STANDER
This appliance may be installed only with clearances as shown in Diagram 4.
DO NOT combine clearances from one type of installation with another in order to
achieve closer clearances.
Measurements below are minimum distances to combustibles.
A Side Wall to Unit: 75mm
BBack Wall to Unit: 150mm
CBack Wall to Flue Centerline: 250mm
DSide Wall to Flue Centerline: 450mm
ESide Wall to Unit: 75mm
FSide Wall to Flue Centerline: 238mm
Minimum ceiling height from top of units is 600mm
HEARTH SIZE
The Logaire Maui needs to be installed on a non-combustible surface no smaller than
the minimum size of the freestander overall dimensions as per Diagram 4.
DIAGRAM 4

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 15
INSTALLATION
CLEARANCE TO COMBUSTIBLES – INBUILT
This appliance may be installed only with the clearances as shown in Diagram 5. Do
not combine clearances from one type of installation with another in order to achieve
closer clearances.
Measurements below are minimum distances to combustibles.
AInsert Top to Top Facing: 250mm
BInsert Top to Mantle: 550mm
CInsert Side to Sidewall: 150mm
DInsert Side to Side Facing: 75mm
EHearth Extension Side: 0mm
FHearth Extension Front: GHearth Height
300mm if 0mm
263mm if 50mm
225mm if 100mm
188mm if 150mm
DIAGRAM 5

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 16
INSTALLATION
MINIMUM FIREPLACE DIMENSIONS
The minimum fireplace dimensions required to be able to install the Logaire gas insert
into a factory built or masonry fireplace are shown in diagram 6 below.
NOTE: Do no remove or alter any part of a factory built fireplace
except glass doors or a smoke shelf which can be
reinstalled if the Logaire gas insert is removed.
DIAGRAM 6

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 17
INSTALLATION
VENTING
The freestanding and inbuilt are vented appliances and must be connected to a
chimney/flue in accordance with the installation codes.
For your safety this heater is equipped with a vent safety switch designed to sense
incorrect venting and reacts by shutting down the gas supply. This heat actuated
switch is located within the draft hood and will detect either a blocked chimney or
backdraft condition. The chimney switch must never be by-passed or disconnected as
a hazardous or deadly condition can result.
FREESTANDER
The Maui Freestander must be installed with a B-vent flue system as approved for use
by Logaire. For cosmetic or aesthetic purposes a 150mm outer flue can be used as
long as an approved inner vent is installed. Fasten the B-vent to the exhaust collar on
the top of the stove. If desired use one MG” sheet metal screw but do not penetrate
the inner sleeve of the B-vent when tightening the screw.
Follow all venting manufacture’s requirements and local building codes. In cold
climates, we recommend the use of insulated B-vent, chase, and liners. For altitudes
above 2000 ft. we recommend that a minumum flue height of 3.7M be used. A wind
cap is recommended for wind turbulent sites when flue spillage is noted. (See page
21).
MODEL INBUILT
The Maui inbuilt must be installed witha B-vent flue system as approved for use by
Logaire with a liner running the full length of the chimney. A minimum flue hight of
3.6m is recommended. B-vent must be supported by a vent support – supplied by the
vent manufacturer.
The Logaire Insert incorporates its own internal draft hood so no additional external
draft hood is required. Periodically check that the vent is not blocked and a sufficient
draft is present when the unit is in operation. Refer to spillage test page 21.
INSTALLATION INTO EXISTING WOODSTOVE/SOLID FUEL
FLUE SYSTEM
Never connect the Maui Gas Fire to a chimney flue serving a separate solid-fuel
burning appliance.
1. Clean and inspect the existing solid fuel chimney.
2. If using B-vent for the entire installation pass the B-vent through the existing
solid fuel chimney. Support the B-vent from the solid fuel chimney top (not
the cap) using vent hangers available from your local vent supplier. Install a
trim collar where the B-vent enters the solid fuel chimney. Connect B-vent to
the spigot collar on the stove using one sheet metal screw.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 18
INSTALLATION
VENTING REQUIREMENTS
Minimum vertical runs shall be no less than 2.4 metres.
Changes of direction from the vertical should be avoided where possible.
NOTE: Vertical run to be at maximum possible distance before any
change in direction.
Where change of direction is unavoidable refer to NZS 5261-1996 Standard / AG601
1995 Australian gas association standard.
Where gradient of lateral (horizontal) runs are required LOGAIRE recommends a
minimum angle of 45% with a minimum run of 600 mm height of vertical flue before
gradient, provided a 1.5 meter vertical run is fitted after any off-set,
Refer to diagram 7.
DIAGRAM 7
Any deviation from minimum and maximum recommended dimensions may effect
performance of the fire.

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 19
INSTALLATION
GAS CONNECTION
The gas connection is ½” SAE 45°flare fitting and is easily accessible at the rear of
the Freestander and on the right side of the Inbuilt. The gas line can be rigid pipe or
to make installation easier use a listed flexible connector and manual shut-off valve if
allowed by local building codes. For minimum and maximum supply pressure, refer
to the compliance plate attached to the unit.
Inlet pressure can be checked on the regulator and manifold pressures can be checked
using the port on the control valve between the variable flame control and the control
knob, and are easily accessible for a test gauge connection. Refer to diagram 8
DIAGRAM 8
NATURAL GAS OR LPG
The F/S and I/B gas stoves are available to burn either Natural gas of LPG. The
burners are specifically manufactured to burn either one. Make sure the stove you
have purchased is equipped for the proper gas.
NOTE:
During any pressure testing of the gas supply piping system
that exceeds test pressures of ½ psig, this appliance and its
individual shutoff valve must be disconnected from the piping
system. If test pressures equal to or less than ½ psig are used
then this appliance must be isolated from the piping system by
closing its individual manual shutoff valve during the testing.




P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 20
INSTALLATION
FASCIA AND ASSEMBLY- INBUILT
1. Attach the right and left fascia sides to the side panel support brackets using two
screws on each side.
2. Connect the two ON/OFF wires to the rocket switch located in the right side of the
fascia top panel.
3. Remove the Top Grill panel from the unit by removing 2x M6 bolts from under
the firebox top. These are accessible by opening the side panels.
4. Attach the fascia top and the top grill panel to the top of the unit using the 2x M6
bolts. Ensure that the tabs on either side of the fascia top insert into the slots on
the top of the fascia sides.
5. Route the power cord through the opening in the bottom of either the left or right
side fascia.
Refer to diagram 9.
WARNING
Failure to position the parts in accordance with this diagram or failure to use only
parts specifically approved with this appliance may result in property damage or
personal injury.
DIAGRAM 9