logika WL-ZAVCDPW-C322121-0 User manual

© 2019 Logika Limited
Smart Cloud Camera
WL-ZAVCDPW-C322121-0
Product Manual
Version 1.0

1
Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
·[e-mail]
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to
ensure safe and proper installation and use.
•Before use, the product must be properly installed as described in this manual by a qualified
technician.
•The product should be used with the supplied accessories.
•Do not disassemble or modify the product.
•Logika is not responsible for any loss due to improper installation or use of this product.
•Please visit our official website at www.logika.nz for more information.
•You can also contact us at the following email address: [e-mail].

2
Device Layout

3
Features
•Communication Mode: IEEE 802.15.4 Zigbee, IEEE 802.11b/g/n.
•Full HD 1080p video.
•Pan and tilt functionality (horizontal 335°, vertical 120°)
•Supports two-way voice communication.
•Built-in motion detection to start recording and send an alarm notification.
•Can be controlled remotely via the mobile app.
Specifications
Communication Protocol
IEEE 802.11/b/g/n, IEEE 802.15.4
Communication Distance IEEE 802.11/b/g/n 50m (visible)
IEEE 802.15.4 500m (visible)
Antenna Configuration Internal Antenna
Overall Power Consumption ≤6W
Wireless Access Mode
WIFI
Rotation Angle (Holder)
Horizontal: 335°, Vertical: 120°
Lens Focal Length
3.6mm
Infrared Lamp Irradiation Distance 5m-6m
Resolution
1080p
Storage
Micro SD (Max storage: 32Gb)
White balance/Backlight compensation/IR
Night Vision Supported
Audio/Video Compression Coding G.722, H.264
Image Rollovers 180°

4
Installation Steps
Installing the Cloud Camera
There are two options for mounting the camera:
Option A: Place the camera upright on a suitable flat surface.
Option B: Mount the camera on the ceiling. Bear in mind that, as the camera is effectively upside
down in this case, you will need to update the orientation in the device settings in the mobile app,
once it has been added to the system. This ensures that you can view the video in the correct
orientation.
1) Remove the base from the camera (attached with magnets).
2) Site the base on the ceiling and mark off where you need to drill the holes for the screws
(supplied). Prior to screwing in the base, make sure you feed in the 12V power cable along
the cable recess in the base.
Remove the base
12V Power Cable
Screw Holes
Cable Recess

5
3) Connect the 12V supply to the camera body and attach it to the base. The main installation
is now complete.
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the
Logika Smart Mobile App user guide which will take you through the process of adding smart
devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app
will walk you through how to add the device to the system.
Device Category:
Camera
Device Name:
Smart Cloud Camera

6
Device Functions
Set Up the Cloud Camera as a Zigbee Gateway
In this mode, the camera can act as a Gateway device, allowing addition of other smart devices on
the network. This means that you do not need to use a Logika Gateway device, as this will perform
the same functions.
To do this, follow the instructions below:
Build the Zigbee Network for the First Time (i.e.. Enter Gateway Mode)
Press the SET key 6 times in quick succession. You will hear an audible notification that the network
is now active.
Add devices to this Gateway
Press the SET key 4 times in quick succession. An audible notification will sound once this is
successfully done. This Gateway is now in a mode which will allow other devices to connect.
Stop Adding Devices
Press the SET key 3 times. An audible notification will sound and no other devices can now be added.
Quit the Zigbee Network
Press and hold the SET key for 10 seconds. After the audible notification, the Cloud Camera will have
exited the network successfully.
Perform a Factory Reset
To completely reset the device settings and remove it from the network, press and hold the SYS key
for 10 seconds until you hear a beep. The device is now in its Factory Default setting.

7
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Quit the Zigbee Network procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at [e-mail] with your issue and we will do our utmost to help!