logika Smart Metallic Curtain Switch User manual

© 2019 Logika Limited
Smart Metallic Curtain Switch
WL-ZCCWNPWA-C111111-0
Product Manual
Version 1.0

1
Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
·[e-mail]
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to
ensure safe and proper installation and use.
•Before use, the product must be properly installed as described in this manual by a qualified
technician.
•The product should be used with the supplied accessories.
•Do not disassemble or modify the product.
•Logika is not responsible for any loss due to improper installation or use of this product.
•Please visit our official website at www.logika.nz for more information.
•You can also contact us at the following email address: suppo[email protected].

2
Device Layout

3
Features
•Communication Mode: IEEE 802.15.4 Zigbee.
•Designed to be used with the Smart Curtain Motor.
•Open or close curtains/blinds by a touch panel, mobile or voice control.
•Support time setting and linkage control to other smart devices.
Specifications
Communication Mode IEEE 802.15.4 ZigBee
Power 100-240V AC, 50/60 Hz
Motor Power 125W 50/60Hz
Load Type AC Curtain Motor
Overall Dimension 86×87×40mm
Material & Colour Silver, Metal
Flame Retardant Rating UL94 V-0
Working Temperature/Humidity -10°C to +45°C, ≤95%RH (Noncondensing)

4
Installation Steps
Hardware Installation
1) Turn off the power prior to installation and wire up the switch to the Smart Curtain Motor
according to the wiring diagram below:
2) Press the Joint Button to release the decorative cap and affix the main body to the inner
(back) box using two screws, as shown:
3) Replace the decorative cap to complete the installation.

5
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the
Logika Smart Mobile App user guide which will take you through the process of adding smart
devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app
will walk you through how to add the device to the system.
Device Category:
Curtain
Device Name:
Smart Metallic Curtain Switch

6
Device Functions
When the device is first powered on, it will normally automatically attempt to connect to the Zigbee
Smart Home network. The System Indicator light will flash as it’s searching for the network. If it
connects, the light will remain on for 2 seconds and then go out.
If this does not happen, you can manually connect via the mobile app and follow the instructions
below.
Join the Zigbee Network
Press the Multi-Function Button once. The System Indicator light will start flashing, signifying it’s
searching for the network.
When it successfully connects, the System Indicator light will stay solid for 2 seconds then go out.
Binding the Curtain Switch to a Curtain Motor
1) Press and hold the Multi-Function button while pressing the On button and then let go.
2) The System Indicator will flash once, signifying that the switch is now sending a binding
request.
3) If the binding succeeds, the System Indicator will flash 3 times. On failure, it will flash 6
times.
You can also perform a binding by utilising the Housekeeper Tasks in the mobile app. Please refer to
the Logika Smart Mobile App user guide for more information.
Quit the Zigbee Network
Long press the Multi-Function Button for 6 seconds. The System Indicator light will flash 4 times and
go out. The device has now been successfully removed from the network and been reset to the
factory defaults.
User Guide
1) Press the On button to start the curtain opening. The curtain will open fully and stop. If you
wish to stop sooner, just press the On button again.
2) Press the Off button to start closing the curtain. Press again to make it stop mid-way.

7
Safety Precautions
• Disable any power prior to connecting the device to the main supply.
• The device must be installed by a qualified electrician.
• The device must be installed in a plastic back box. If installed in a metallic back box, the signal
will be impaired.
• Do not disassemble or refit this product or its accessories.
• The device should be mounted in a dry environment. It is not designed to be used
outdoors.

8
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Quit the Zigbee Network procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at [e-mail] with your issue and we will do our utmost to help!