LogiLink HD0101 User manual

Size: 84 x 118.4mm
* 100P 雪銅紙
* 拉頁, 一本德文(在前)英文手冊,
另一本西班牙文(在前)波蘭文手冊
* 兩面, 正四色反四色彩色印刷

- 1 -
Do not throw the appliance away with the normal
household waste at the end of its life, but hand it in at
an official collection point for recycling. By doing this
you will help to preserve the environment.
1.0 Safety Instructions
Put the Device always on a stable and straight Surface. In case
of falling it can be damaged.
Don’t place the Device into direct Sunlight or in Places with high
Temperature. This can damage the Device or shorten his
average useful Life.
Don’t place it in the near of Heat Sources, like Radiators or other
heat producing Devices.
Don’t expose the Device to Rain, Water, Wetness or high Humidity.
Don’t place it in the Bathroom or the Kitchen in the near of a Sink.
Avoid the direct Contact with Water.
Don’t try to open the Device.
Prior to the first use of our product make a backup of your data.
We are not liable for any loss of data, unless you can accuse us
intention or gross negligence.
In any case, liability for loss of data is limited to the effort that is
necessary to restore from existing backup copies.
Congratulations to the Purchase of Logilink HD0101!
Please read the Manual and Safety Instructions before using the
product for the first time. Otherwise damage can be the result.

- 2 -
2.0 Introduction
The HDMI Repeater extends the length of any HDMI cable by
regenerating the HDMI signal before it sends the outputs to the
HDMI monitor or projector. The HDMI Repeater will clean out the
digital noise (sparkles) in your picture. The input of the HDMI
repeater is connected with a long HDMI (male to male) cable
from the HDMI device like DVD player or Satellite set top box
with a HDMI output port. The HDMI repeater output is connected
to a second HDMI (male to male) cable to go from the output to
any HDMI display or projector with a HDMI connector. The box
is placed near the display to remove any noise that has been
generated by a long HDMI cable.
2.1 Features
This kind of the HDMI Repeater has many features that enable it
to perform in a superior manner. Among those features you will
find:
Compliance with HDMI High Speed specification
Extends the HDIM signal up to 35 m
HDTV: 480i/576i/480p/576p/720p/1080i/1080p
Bandwidth: 165MHz/1.65Gbps per channel (4.95Gbps all
channel)
Supports HDCP pass-through, LPCM
Supports 8bit per channel (24bit all channel) deep color

- 3 -
2.2 Specifications
Signal Inputs/Output
Input Video Signal 5 Volts p-p (TTL)
Maximum Single Link Range 1920x1080P
Output Video HDMI High Speed
HDMI Input/Output
Connector
Type A 19 pin
Operating Frequency
Vertical Frequency Range 50/60Hz
Video Amplifier Bandwidth 1.65Gbps/165MHz
Resolutions(HDTV)
Interlaced(50&60Hz) 480i, 576i, 1080i
Progressive(50&60Hz) 480p, 576p, 720p, 1080p
Mechanical
Size (W-H-D) 27mm x 49mm x 15mm
Weight(Net) 0.017KGs
Environmental
Operating Temperature 0 ºC to +70 ºC
Operating Humidity 10% to 85 % RH (no
condensation)
Storage Temperature -10 ºC to +80 ºC
Storage Humidity 5% to 90 % RH (no condensation)
Power Requirement
External Power Supply 5V DC@2A(optional)
Power consumption (Max) 3W
Accessories Adapter
AC Power Adapter US standard, UK standard and so
on
Note: Specifications are subject to change without notice.
2.3 Package Contents
HDMI Repeater
User Manual

- 4 -
3.0 Panel Descriptions
HDMI input Power input HDMI output
4.0 Connection and Operation
1) Connect the source device output into input of the HDMI
Repeater and connect output of the HDMI Repeater to the
HDMI display unit. The HDMI Repeater is put close to the
HDMI display unit (Input cables are optional)
* Please refer to connection diagram section.
2) Insert the DC side of 5v power supply if the 5v of the source is
not enough.
Attention: Insert / Extract cable gently.
Connection Diagram
The CE mark confirmed that this product meets the
main requirements of the Directive 2004/108/EC of
the European Parliament and the Council of
Europe concerning telecommunications and
terminals regarding the Safety and health of users
and of electro-magnetic interference compliance.
The CE has been demonstrated. These statements
are deposited by the manufacturer.