Logitech X50 User manual

Logitech® X50
Product Manual

Logitech X50
2
Contents
English. . . . . . . . . . . . . . . . . . . 3
繁体中文 . . . . . . . . . . . . . . . . . . 8
한국어 . . . . . . . . . . . . . . . . . . . 13

Logitech X50
English 3
Features
1
2 4 5
3
1. Power / Bluetooth Pairing Button
2. Volume Buttons
3. 3.5mm Aux-In Jack
4. Micro USB Connector
5. Status LED

Logitech X50
4 English
Power
Note: To save power, X50 will automatically turn itself o after 15 minutes of no Bluetooth connection.
ON/OFF

Logitech X50
English 5
Connection – via Bluetooth
3s
Pairing your first device
When you turn X50 on for the first time, it automatically goes into pairing mode and searches for
a Bluetooth source device to pair with. X50 works with Bluetooth-enabled devices that support
Advanced Audio Distribution Profile (A2DP), such as smartphones, tablets and personal computers.
Pairing additional devices
To pair X50 with additional source devices, press and hold the Power / Bluetooth pairing button
for 3 seconds. X50 will enter pairing mode, make a sound, and flash its Bluetooth LED while
searching for another device. Once the next device is paired with, X50 will sound to confirm
pairing and the Bluetooth LED will remain solid blue.
X50 will remember the last 8 devices it was connected to. The next time the speaker is turned
on, it will attempt to reconnect automatically to the last device it was connected to before it was
turned o.
X50’s Bluetooth range is approximately 10 meters, or 30 feet. If you take your source device out
of range, the connection will be suspended. X50 will automatically reconnect if the source device
is brought back in range within 5 minutes. After 5 minutes, the active connection will be dropped.
– – – – – – – – – – – – – – – – – – – – – –
10 m (30 ft)

Logitech X50
6 English
Connection – via Auxiliary input
You can also connect X50 with any source devices using a 3.5mm auxiliary cable.
AUX AUX

Logitech X50
English 7
LED Indication
Not Charging -
Normal Battery
Not Charging -
Low Battery Charging Fully Charged
Power O OFF OFF Breathing in
PURPLE colour OFF
Power On -
Pairing
Fast blinking in
BLUE colour
Fast blinking in
RED colour
Fast blinking in
PURPLE colour
Fast blinking in
BLUE colour
Power On -
Connectable
Slow blinking in
BLUE colour
Slow blinking in
RED colour
Slow blinking in
PURPLE colour
Slow blinking in
BLUE colour
Power On -
Connected Steady BLUE Steady RED Steady PURPLE Steady BLUE

羅技 X50
8 繁体中文
功能
1
2 4 5
3
1. 電源 / 藍牙 配對按鈕
2. 音量按鈕
3. 3.5 公釐輔助輸入插孔
4. Micro USB 接頭
5. 狀態 LED 指示燈

羅技 X50
繁体中文 9
電源
注意： 為節省電力，X50 會在沒有 藍牙 連線 15 分鐘後自動關閉電源。
開/關

羅技 X50
10 繁体中文
連線 – 透過 藍牙
3s
配對您的第一個裝置
當您第一次開啟 X50 電源時，它會自動進入配對模式並搜尋 藍牙 來源裝置以與其配對。X50 可搭
配支援先進音訊散播協定 (A2DP) 的 藍牙 裝置使用，例如智慧型手機、平板電腦與個人電腦。
與其他裝置建立配對
若要將 X50 與其他音源裝置配對，請按住電源 / 藍牙 配對按鈕 3 秒鐘不放。X50 會進入配對模
式，並在搜尋其他裝置時發出提示音效以及閃爍其 藍牙 LED 指示燈。與下一個裝置完成配對
後，X50 就會發出配對確認音效，且 藍牙 LED 指示燈會保持穩定藍燈。
X50 可記憶最近曾連線的 8 個裝置。下次音箱開啟電源時，會自動嘗試重新連線到電源關閉前的
最後一個連線裝置。
X50 的 藍牙 範圍大約是 10 公尺，或者 30 英呎。如果您將音源裝置帶離此範圍之外，連線就會
中止。如果音源裝置不超過 5 分鐘又進入範圍之內，X50 會自動重新建立連線。如果超過 5 分 鐘，
現用的連線會被棄用。
– – – – – – – – – – –
10 公尺 (30 英呎)