LongerPump TS-1A/L0107-1A User manual

TableofContents
Introduction
Operation Panel
Basic Operation
Menu Frame Work
Multi-channel Running Interface
Multi-channel Functions Setting
Single Channel Running Interface
Single Channel Functions Setting
Acceptable Drive Units and Syringes
Syringe Loading
External Control Function
Maintenance
Warranty
Technical Specifications
Start/Stop Key
Fast Forward Key
Fast Reverse Key
Rotary Coded Switch
Channels Switch Key
Exit Key
Select Drive Unit
Select Copy Parameters
Set Delay Time
Controller I.D.
Working Mode Selection
Syringe Select
Dispense Parameters Setting
Calibration
Display Select
Important Information:
Warning:
Please read operating manual carefully before operation.
Over-push or over-draw the syringe may result in the fluid
sprayed. Use appropriate measures to protect operator
and equipment. Be careful during operation.
When the fluid sprays out on the drive unit please shut
down the power supply immediately and clean the drive
unit, then turn on the power supply.
If a trouble happens please contact us or our dealer. Don't
repair the equipment by yourself.
Be careful when inserting or extracting the connection
wire between controller and drive unit to prevent the plug
from damaging.
If the power line or the plug are worn or damaged please
pull out the plug.
Please shut down the power supply before connecting the
external control equipment.
SYRINGE PUMP OPERATING MANUAL
1
2
2
2
4
4
6
8
8
9
11
15
2
2
2
2
2
3
4
16
17
19
21
5
6
5
21
21
22

1
F1 F5
F4
F3
S1
S2
S3
2
F2
Introduction
TS series products are controllers of four channels and multi-function
syringe pumps. They need to be connected with drive units to constitute
syringe pump systems of strong functions and easy-to-operate. They are
widely used in biological laboratory. There are 3 types:
Controller Type
TS-1A
TS-2A
TS-1B
DriveUnitType
L0107-1A
L0107- A
W0109-1B
2
Working Mode
Infusion-only
Infusion/Withdrawal
Infusion/Withdrawal
S1 Controller
S2 Drive Unit
S3 Glass Syringe
Note:
Controller and drive unit are connected through 8 pin S terminal.
Be careful when insertion or extraction. Please see page 21 for
detail information about control function.External
F1 Power Switch
F2 Power Socket
F3DriveUnitSocket
F4 External Control Input and Communication Interface
F5 External Control Output Interface
Operation Panel
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
Fast Forward Key
Exit Key
Channels Switch Key
Fast Reverse Key
Start/Stop Key
Rotary Coded Switch
Basic Operation
Start/Stop Key
Press the Start/Stop Key to start or stop the pump. In multi-
channel working mode, to pause the running state, the pump will
prompt if continue the current working state.
Fast Forward Key
In multi-channel working mode, pressing the Fast Forward Key all
the enabling channels infuse at the max. speed. In single channel
working mode, pressing the Fast Forward Key this channel infuses
at the max. speed. Loose this key the pump stops. Other keys are
invalid when pressing this key.
Fast Reverse Key
In multi-channel working mode, pressing the Fast Reverse Key all
the enabling channels withdraw at the max. speed. In single
channel working mode, pressing the Fast Reverse Key this channel
withdraws at the max. speed. Loose this key the pump stops. Other
keys are invalid when pressing this key.
Note: Fast Forward Key and Fast Reverse Key are invalid when the
pump is in running state.
Rotary Coded Switch (RCS)
Turn the Rotary Coded Switch for menu selection or parameter
setting. Press the Rotary Coded Switch for confirmation.
Note: Put the finger in the center of the switch to press the RCS.
Put the finger on the small concave which is on the side of the
switch to turn the RCS.
Channels Switch Key
Switch between different channels.
Exit Key
Cancel current operation and return to previous menu.

Select Unit：
1# 2# 3# 4#
Copy Para Sel：
1# 2# 3# 4#
Delay time：
1# 6.0 sec
2# 0.0 sec
4# 0.0 sec
3# 0.0 sec
Controller ID：
1
1#:
2#:
3#:
4#:
3 4
1#:
2#:
3#:
4#:
a
b
c
d
e
1#:
2#:
3#:
4#:
Select Unit：
1# 2# 3# 4#
Copy Para Sel：
1# 2# 3# 4#
1# 2# 3# 4#
1# 2# 3# 4#
1# 2# 3# 4#
1# 2# 3# 4#
Save change?
Yes o CancelN
1# 50.00 nL/sec
20.0 sec
Syringe： 100 Lμ
2#V ： 360ol Lμ
40 sec 5
Syringe： 500 Lμ
3# ： 860 LμVol
68.3 sec 10
Syringe： 1000 Lμ
4# ：700 nLVol
25 sec 1
Syringe：10Lμ
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
Menu Frame Work
Mode Select
yringe Select
Dispense Para
Calibration
Display Select
S
Mode Select
yringe Select
Dispense Para
Calibration
Display Select
S
Mode Select
yringe Select
Dispense Para
Calibration
Display Select
S
Mode Select
yringe Select
Dispense Para
Calibration
Display Select
S
Mode Select
yringe Select
Dispense Para
Calibration
Display Select
S
Infusion
Withdrawal
I/W
W/I
Continuous
Unimetrics
Becton Dickinson
Hamilton
Barrel I.D.
Disp Vol Unit
L
Infusion Unit
sec
ithdrawal Unit
sec
Copy No.:
ause Time:
min
186 0.01
8.5
W
7.0
10
P
0.1
μ
Save change?
Yes o CancelN
Vol 50.00：
：
：
μ
μ
L
Time 60sec
Act 50.00 L
Display Select
Volume
Speed
Flow
：
Multi-channel Running Interface
Switch on the pump. First initializing, and then display the running
interface.
a. Enabling symbol: Symbol of enabling or disabling the channels.
Means enabling the current channel. means disabling the
current channel. The disabling channel is invalid when the pump is
in running state or switching the channels.
b. Channel number: Channel serial number.
c. Start/Stop state: Display the state of current channel.
Start displays Stop displays Pause displays
d. Direction: Display running direction. Infusion displays .
Withdrawal displays .
e. Working mode: Display current working mode. Display in
“infusion, withdrawal, infusion/withdrawal, withdrawal/infusion”
modes. Display in “continuous” mode.
.. .
Multi-channel Functions Setting
Select Drive Unit:
Means enabling the current channel. Means disabling the current
channel. The disabling channel will not work when the pump is
working. The setting method is as below:
Press the RCS
Press the
Exit Key
Press the RCS
Select “Yes”
or “No” Turn the RCS
Press the
Exit Key
Select
“Cancel”
Turn the RCS to select
if save the change
Select Unit：
Copy Para Sel：
Select Unit：
Copy Para Sel：
PresstheRCStoset
the enabling channels
Turn the RCS to
select the channels

5
1#:
2#:
3#:
4#:
1# 2# 3# 4#
1# 2# 3# 4#
1# 2# 3# 4#
1# 2# 3# 4#
1# 2# 3# 4#
1# 2# 3# 4#
1#:
2#:
3#:
4#:
1# 2# 3# 4#
1# 2# 3# 4#
1# 6.0 sec：
2# 0.0 sec：
3# 0.0 sec：
1# 6.0 min：
2# 0.0 sec：
4# 0.0 sec：
3# 0.0 sec：
1# 6.0 min：
2# 0.0 sec：
4# 0.0 sec：
3# 0.0 sec：
6
1#:
2#:
3#:
4#:
1# 2# 3# 4#
1# 2# 3# 4#
1
1
1# 6.0 sec：
2# 0.0 sec：
3# 0.0 sec：
1#:
2#:
3#:
4#:
8.3 sec 10
Syringe ： 100 Lμ
1# 1.860 L Vol ：μ
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
Press the RCS
Press the
Exit Key
Press the
Exit Key
Press the RCS
Press the
Exit Key
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the
Exit Key
Press the RCS
Press the
Exit Key
Press the RCS
Press the RCS
Press the Exit Key
Select “Yes”
or “No”
Turn the RCS
Select “Yes”
or “No”
Turn the RCS
Select “Yes” or “No”
Turn the RCS
Select
“Cancel”
Select
“Cancel”
Select
“Cancel”
Select Copy Parameters
Select the parameters of one drive unit as copy parameters, all
enabling channels will run according to copy parameters. Not setting
copy parameters each enabling channel will run according to its own
parameters setting. Means copy channel; means non-copy
channel. Only one channel can be selected as copy channel, or non-
copy channel is acceptable. The setting method is as below:
Press and
turn the RCS
Turn the RCS to select
the copy channel
PresstheRCStoset
the copy channel
Turn the RCS to select
if save the change
Set Delay Time
Set delay time to start each drive unit in turn. Time units are sec,
min and hour. Time numerical value is from 0.1 to 999.9. The
setting method is as below:
Turn the RCS to select channel
Turn the RCS to set the time unit
Turn the RCS to set the delay time
Turn the RCS to select if save
the change
Controller I.D.
When control computer controls many pumps through RS485
interface, it must identify each controller's I.D.. This controller I.D.
should be unique. It's the identification of this controller.
The controller address serial number is from 1 to 30. The default is
1. The setting method is as below:
Single Channel
Running Interface
Switch on the pump. First initializing, and then display the multi-
channel running interface. Press Channels Switch Key to enter single
channel running interface. Please see below for detail operation:
Turn the RCS to select
if save the change Turn the RCS to set the
controller I.D.
Press Channels
Switch Key
Press Channels
Switch Key
Press Channels
Switch Key
Press Channels
Switch Key
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Select Unit：
Copy Para Sel：
Select Unit：
Copy Para Sel：
Select Unit：
Copy Para Sel：
Select Unit：
Copy Para Sel：
Delay time：
Delay time：
Delay time：Delay time：
Select Unit：
Copy Para Sel：
Controller ID：
Controller ID：
8.3 sec 10
Syringe ： 100 Lμ
2# 1.860 L Vol ：μ
8.3 sec 10
Syringe ： 100 Lμ
3# 1.860 L Vol ：μ
8.3 sec 10
Syringe ： 100 Lμ
4# 1.860 L Vol ：μ

Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
a.Display mode: Display the current volume, flow rates or speed.
Please see page 16 “Display Select” for setting method.
b.Time: Required time for one time infusing or withdrawal.
Counting down when running.
c.Syringe: Display selected syringe.
d.Start/Stop state: Start displays Stop displays Pause
displays
e.Copy number: Display dispensing copy number. Counting down
when running (no display in “continuous” mode).
f. Working mode: Display current working mode. Display in
“infusion, withdrawal, infusion/withdrawal, withdrawal/infusion”
modes. Display in “continuous” mode.
g.Direction: Display running direction. Infusion displays .
Withdrawal displays .
;;
.
87
Volume Display
b.
c.
d.
e.
g.
a.
f.
Flow Rate Display
Speed Display
1#： 6.715mm/min
8.3 sec 10
1#： 224.0nL/sec
8.3 sec 10
Single Channel Functions Setting
5 functions are set:
Working Mode Selection
8.3 sec 10
Continuous
Display Select
Note: TS-1A controller disables Mode Select. It only has infusion
working mode.
Three Display Modes for Single
Channel Running Interface:
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
Press the RCS
Press the
Exit Key
Press the Exit Key
Press the RCS
Press the
Exit Key
Press the RCS
Press the RCS
Select “Yes”
or “No”
Turn th e RCS
Turn the RCS
Select
“Cancel”
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the RCS to select
if save the change
Turn the RCS to
select working mode
Turn the RCS to
select working mode
Prompts
Infusion: The pump infuses during the whole working course
Withdrawal: The pump withdraws during the whole working course
Infusion/Withdrawal: The pump infuses first and then withdraws during the
whole working course
Withdrawal/Infusion: The pump withdraws first and then infuses during the
whole working course
Continuous: The pump infuses first and then withdraws, and then cycles
continuously
Please see page 11 “Dispensing Parameters Setting” to set the parameters for
above working modes.
Save change?
Yes o CancelN
8.3 sec 10
Syringe ： 100 Lμ
1# 1.860 L Vol ：μ
Syringe ： 100 Lμ
Syringe ： 100 Lμ
8.3 sec 10
Syringe ： 100 Lμ
1# 1.860 L Vol ：μ
Mode Select
yringe Select
Dispense Para
Calibration
S
Mode Select
yringe Select
Dispense Para
Calibration
S
Infusion
Withdrawal
I/W
W/I
Syringe ： 100 Lμ
1# 1.860 L Vol ：μ
Turn the RCS to select
working mode

Turn the to select
the specification
RCS
9
8.3 sec 10
Size Select
I.D.
()μL
5102550
100 250 500 1000
： 1.13mm
Spec L()μ
I.D. mm()
Unimetrics 10
0.46
25
0.73
50
1.03
100
1.46
250
2.3
500
3.26
1000
4.61
I.D. mm()
1
4.7
3
8.59
5
11.99
10
14.48
20
19.05
30
21.59
60
26.6
I.D. mm()
1
4.61
2.5
7.28
5
10.3
10
14.57
25
23.03
50
32.57
10
8.3 sec 10
1# 10.00mm
2# 10.00mm
3# 10.00mm
4# 10.00mm
：
：
：
：
1# 8.00mm
2# 10.00mm
3# 10.00mm
4# 10.00mm
：
：
：
：
1# 8.00mm
2# 15.00mm
3# 10.00mm
4# 10.00mm
：
：
：
：
2.Select the Inner Diameter of the Syringe
Select the inner diameter of the syringe after setting the inner diameter.
1# 8.00mm
2# 10.00mm
3# 10.00mm
4# 10.00mm
：
：
：
：
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
Press the RCS
Press the Exit Key
Press the RCS
Press the
Exit Key
Press the RCS
Press the RCS
Press the
Exit Key
Press the
Exit Key
Press the
Exit Key
Press the RCS
Press the RCS
Select “Yes” or “No”
Select “No”
Select “Yes”
Select “Yes”
or “No”
Select “Yes” or “No”
Press the
Exit Key
Select
“Cancel”
Select
“Cancel”
Press and
turn the
RCS
Press and
turn the
RCS
Press and
turn the
RCS
Syringe Select
Select Standard Syringe
Three syringe manufacturers are listed in the TS-1B menu. Please see
below table for specifications:
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Setting and Select the Inner Diameter of the Syringe
1. Setting the Inner Diameter of the Syringe
If the syringe used is not listed in the menu the inner diameter of
the syringe needs to be measured and entered (0.01 mm - 40 mm).
The pump can save 4 inner diameters of the syringes.
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the RCS to highlight
“Syringe Select”
Turn the to select
the type
RCS
Turn the to select
if save the parameter
RCS
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Turn the to highlight
the Syringe Select
RCS
“”
Turn the to select
if save the change
RCS
Turn the to select
if save the change
RCS Turn the to set
the inner diameter
RCS
Select
“Cancel”
Turn the to select
if save the change
RCS
Select
“Cancel”
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Mode Select
yringe Select
Dispense Para
Calibration
S
Mode Select
yringe Select
Dispense Para
Calibration
S
Save change?
Yes o CancelN
Syringe ： 100 Lμ
1# Vol ：1.860 Lμ
Unimetrics
Becton Dickinson
Hamilton
Barrel I.D.
Syringe ： 100 Lμ
1# 1.860 L Vol ：μ
Unimetrics
Becton Dickinson
Hamilton
Barrel I.D.
Unimetrics
Becton Dickinson
Hamilton
Barrel I.D.
Becton
Dickinson
Hamilton
Spec cc()
Spec m()L
Spec L()μ
I.D. mm()
Unimetrics 10
0.46
25
0.73
50
1.03
100
1.46
250
2.3
500
3.26
1000
4.61
I.D. mm()
0.48 0.73 1.03 1.46 2.3 3.26
I.D. mm()
25
0.73
50
1.03
100
1.46
250
2.3
500
3.26
SGE
Hamilton Spec L()
μ
Spec L()μ
10 25 50 100 250 500
Three syringe manufacturers are listed in the TS-1A,TS-2A menu.
Please see below table for specifications:

Note:
When the pump can't infuse the setting volume in the setting time
the running interface will display “I-speed Overflow” (see below).
Pleaseadjustthedispensingtimeorthedispensingvolume.
11
8.3 sec 10
Vol overflow！
8.3 sec 10
Syringe: 100 Lμ
12
8.3 sec 10
I-speed Overflow！
8.3 sec 10
Syringe: 100 Lμ
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the
Exit Key
Press the
Exit Key
Press the
Exit Key
Press the
Exit Key
Select “Yes” or “No”
Select “Yes” or “No”
Select “Cancel”
Press the RCS
Select “Cancel”
Press and
turn the
RCS
Press and
turn the
RCS
Press and turn the RCS
Dispense Parameters Setting
The dispense parameters include dispense volume, infusion time,
withdrawal time, copy number and pause time.
Dispense volume: It is the volume for one time infusion or withdrawal
The volume range is 1 nL to 99.99 mL
There are volume units of nL, 0.01nL, 0.1µL, µL and 0.01mL available.
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the and highlight
the “Dispense Para”
RCS
Turn the and set the unitRCS
Turn the to
set the volume
RCS
Turn the to select
if save the parameter
RCS
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Note:
When the one time dispensing volume or the total dispensing volume
(multiply one time dispensing volume by copy number) are more than
the volume of the syringe the running interface will display “Vol
Overflow” (see below). Please change the syringe or adjust the
dispensing volume or the copy number.
Infusion time: It is the time for one time infusion
The range of infusion time is from 0.1 second to 999.9 hours
There are time units of second, minute and hour available
Turn the and highlight
the Dispense Para
RCS
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Turn the and set the unitRCS
Turnthe tosetthetimeRCSTurn the to select
if save the change
RCS
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Mode Select
yringe Select
Dispense Para
Calibration
S
Mode Select
yringe Select
Dispense Para
Calibration
S
Syringe ： 100 Lμ
1# L Vol ：1.860 μ
Disp Vol Unit
86 0.01 L
Infusion Unit
8.5 sec
1μ
Disp Vol Unit
86 0.01 L
Infusion Unit
8.5 sec
1μ
Disp Vol Unit
86 0.01 L
Infusion Unit
8.5 sec
1μ
Syringe ： 100 Lμ
1# Vol ：1.860 Lμ
Disp Vol Unit
86 0.01 L
Infusion Unit
8.5 sec
1μ
Disp Vol Unit
86 0.01 L
Infusion Unit
8.5 sec
1μ
Disp Vol Unit
86 0.01 L
Infusion Unit
8.5 sec
1μ

Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Note:
When the one time dispensing volume or the total
dispensing volume (multiply one time dispensing volume
by copy number) are more than the volume of the syringe
the running interface will display “Vol Overflow” (see
right). Please change the syringe or adjust the dispensing
volume or the copy number.
8.3 sec 10
W-speed Overflow！
8.3 sec 10
Syringe： 100 Lμ
13 14
8.3 sec 10
Pause Time:
0.1 min
8.3 sec 10
Pause Time:
0.1 min
8.3 sec 10
Press the RCS
Press the
Exit Key
Press the
Exit Key
Press the RCS
Press the RCS
Press the RCS
Press the
Exit Key
Press the Exit Key
Press the RCS
Press the RCS
Press the RCS
Press the
Exit Key
Press the Exit Key
Select “Yes” or “No”
Select “Yes” or “No”
Select “Yes” or “No”
Select “Cancel”
Select “Cancel”
Select “Cancel”
Press and turn the RCS
Press and
turn the
RCS
Press and
turn the
RCS Press and turn the RCS
Press and
turn the
RCS Press and turn the RCS
Withdrawaltime:Itisthetimeforonetimewithdrawal
The range of withdrawal time is from 0.1 second to 999.9 hours
There are time units of second, minute and hour available
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the and highlight
the “Dispense Para”
RCS
Turn the and set the unitRCS
Turnthe tosetthetimeRCS
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Turn the to select
if save the parameter
RCS
Note:
When the pump can't withdrawal the setting volume in the setting
time the running interface will display “W-speed Overflow” (see
below). Please adjust the dispensing time or the dispensing volume.
Copy Number: It is the total infusion and withdrawal numbers of the
whole working course. The range is 1 - 999. In Infusion/Withdrawal
(I/W) and Withdrawal/Infusion (W/I) modes, one time working
course is finishing one time infusion and withdrawal.
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the and highlight
the“DispensePara”
RCS
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting Turn the and set
the copy number
RCS
Turn the to select
if save the parameter
RCS
Pause Time: It is the stop time between two dispensing operation.
Therangeis0.1- 999.9min.
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the and highlight
the“DispensePara”
RCS
Turn the to select
if save the parameter
RCS
Turn the and set the pause timeRCS
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Mode Select
yringe Select
Dispense Para
Calibration
S
Mode Select
yringe Select
Dispense Para
Calibration
S
Mode Select
yringe Select
Dispense Para
Calibration
S
Withdrawal Unit
8.3 sec
Copy No.:
1
Withdrawal Unit
8.3 sec
Copy No.:
1
Withdrawal Unit
8.3 sec
Copy No.:
1
Withdrawal Unit
60.0 sec
Copy No.:
1
Withdrawal Unit
60.0 sec
Copy No.:
1
Syringe ： 100 Lμ
1# Vol ：1.860 Lμ
Syringe ： 100 Lμ
1# Vol ：1.860 Lμ
Syringe ： 100 Lμ
1# Vol ：1.860 Lμ
Vol overflow！
Syringe: 100 Lμ
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

15
8.3 sec 10
Interface A
16
Display Select
8.3 sec 10
Press the
Exit Key
Press the
Exit Key
Press the Exit Key
Press the
Exit Key
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Press the RCS
Select “Yes” or “No”
Select “Yes” or “No”
Select “Yes” or “No”
Select “Cancel”
Select “Cancel”
Select “Cancel”
Press and
turn the
RCS
Press and
turn the
RCS
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the to select
if save the parameter
RCS
Turn the to select
if save the parameter
RCS
Calibration
When the accuracy of the dispensing volume can not reach 0.5% (in
the condition of 30% of max. infusion distance), calibration is
needed to adjust the linear speed of the drive unit.
≥
Turn the and
highlight the “Calibration”
RCS
Press the
to start the test
Start/Stop
Key
Turn the to enter
the calibration volume
RCS
Turn the to enter
the actual volume
RCS
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Volume (Vol): The required volume for calibration
Enter volume setting interface (see Interface A) and turn the
to set the calibration volume. There are 10%, 50% and 80% of the
syringe volume available. When selecting the user-defined syringe
the default calibration volume is 50% of the syringe volume. Please
see page 9 “Syringe Select” to select suitable syringe.
Time: The calibration time for the pump is 1 minute.
Actual volume (Act): Press the after setting the
calibration volume. Enter the actual volume.
RCS
Start/Stop Key
Please see page 16 “Display
Select” for “Speed” and
“Flow” display.
Turn the and highlight
the “Display Mode”
RCS Turn the to select
the Display Mode
RCS
Turn the to select
if save the parameter
RCS
There are volume, speed and flow rate display modes available.
Volume: Display current one time infusion or withdrawal volume
Speed: Display current running speed
Flow rates (Flow): Display current flow rates
Note:
Select “Yes” to save the
current setting
Select“No”nottosave
the setting
Select “Cancel” to return
to previous menu and
keep on selecting
Save change?
Yes o CancelN
Save change?
Yes o CancelN
Mode Select
yringe Select
Dispense Para
Calibration
S
Display Select Display Select
Volume
Speed
Flow
：
Syringe ： 100 Lμ
1# Vol 1.860 L ： μ
Syringe ： 100 Lμ
1# Vol 1.860 L ： μ
Save change?
Yes o CancelN
Vol 10.00：
：
：
μ
μ
L
Time 60sec
Act 10.00 L
Vol 10.00：
：
：
μ
μ
L
Time 60sec
Act 10.00 L
Vol 10.00：
：
：
μ
μ
L
Time 60sec
Act 10.00 L
Vol：
：
：
10% 50% 80%
Time 60sec
Act 10.00 Lμ
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

17 18
Acceptable Drive Units and Syringes
Syringe Material
Glass Syringe
Specification
Glass Syringe
Inner Diameter
(mm)
Flow Rate
（
（
μL
/min
)
)
10 25 50 100 250 500 1000
Glass Syringe
1.318nL
-
13.18μL
3.320nL
-
33.20μL
6.610nL
-
66.10μL
13.282nL
-
132.82μL
32.96nL
-
329.6μL
66.22nL
-
662.2μL
132.42nL
-
1324.2μL
T -1A/L0107-1A、S TS-2A/L0107-2A
TS-1B/W0109-1B
Controller
Glass Syringe
Drive Unit
Reference Flow Rates List
Glass Syringe
Drive Unit
Controller
Syringe Material
Syringe
Specification
Flow Rate
（
（
μL)
/min)
Glass Syringe
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
10 25 50 100 250 500 1000
1.318nL
-
13.18μL
3.320nL
-
33.20μL
6.610nL
-
66.10μL
13.282nL
-
132.82μL
32.96nL
-
329.6μL
66.22nL
-
662.2μL
132.42nL
-
1324.2μL
Syringe Material
Syringe
Specification
Flow Rate
（
（
cc
/min
)
)
Plastic Syringe
0.138
-
1.38
μL
mL
0.460
-
4.60
μL
mL
0.896
-
8.96
μL
mL
1.306
-
13.06
μL
mL
2.261
-
22.61
μL
mL
2.904
-
29.04
μL
mL
4.409
-
44.09
μL
mL
Syringe Material
Syringe
Specification
Flow Rate
（
（
mL
/min
)
)
Plastic Syringe
135
10 20 30 60
12.5 510 25 50
0.132
-
1.32
μL
mL
0.330
-
3.30
μL
mL
0.661
-
6.61
μL
mL
1.323
-
13.23
μL
mL
3.305
-
33.05
μL
mL
6.610
-
66.10
μL
mL
0.46 0.73 1.03 1.46 2.3 3.26 4.61

19
Syringe Loading
20
1. Lift up and rotate
the pressing knob
2. See above drawing
to load the glass
syringe
TS-1A/L0107-1A
Loading Pole
Pressing Knob
TS-1B/W0109-1B
Pressing Knob
Plunger Fixing Board
Barrel Fixing Board
TS-2A/L0107-2A
1. Lift up and rotate
the pressing knob.
Rotate and loose
the tightening
knobs according to
the arrowhead
directions
3. Lift up the pressing
knob and rotate the
press knob according
to the arrowhead
direction to fix the
glass syringe
Pressing Knob
Loading Pole
Tightening
Knob 2
3. Rotate the tightening
knobs according to
the arrowhead
directions to fix the
glass syringe
2. See above drawing
to load the glass
syringe. Lift up the
press knob and
rotate the press
knob according to
the arrowhead
direction to press
the glass syringe
1.Rotate the tightening
knobs according to the
arrowhead directions.
Loose the plunger fixing
board and the barrel
fixing board
2.Lift up the pressing knob
and rotate the pressing
knob according to the
arrowhead direction.
Load the syringe. Rotate
the pressing knob to
press the syringe
3.Tighten the tightening
knobs according to the
arrowhead directions to
fix the syringe
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL
Tightening
Knob 1

Maintenance
Warranty
Keep the surface of the pump clean and dry. Prevent the liquids
from entering the inner of the drive units.
The surface of drive units are not organic solvent and aggressive
liquids resistant. Please pay attention when using.
Note
If a trouble happens, please contact us or our dealers.
The warranty period for this product is one year. If repair or
adjustment is necessary within the warranty period, the problem
will be corrected at no charge if it is not due to misuse or abuse on
your part, as determined by the manufacturer. Repair costs outside
the warranty period, or those resulting from product misuse or
abuse,maybeinvoicedtoyou.
21
Stop State: OC gate is open
Running State: OC gate is close
Infusion: OC gate is open
Withdrawal:OCgateisclose
22
External Control Function
1234
External Control Output Interface
External Control Input and Communication Interface
5678
9101112
13 14 15 16
Channel 1
12345678
（1 2)(5 6)(9 10)(13 14)
are 4 suits OC gates
（3 4)(7 8)(11 12)(15 16)
are 4 suits OC gates
TS-1A/L0107-1A、TS-2A/L0107-2A、TS-1B/W0109-1B
Technical Specifications
System Functions
Parameters Setting: The parameters of each channel can be different
Parameters Saving: The parameters of each channel can be saved
Running Control: Each drive unit can be controlled separately; Or four
drive units can be controlled to run simultaneously or run at
different time
Copy Channel: All drive units can be run according to the parameters of
one drive unit of them
Delaying Startup: Delaying startup time of each channel can be
controlled separately
Memory Function: Select resume operation or remain stopped when
power returns after an interruption
Block Protection: When one drive unit stops accidently, the system will
warm and stop
External Control: Each channel has two ways OC gate output to
indicate the start/stop and running direction of this channel
Communication: Realize computer control through RS485
communication interface
Main Functions for Each Channel
Channel 2 Channel 3 Channel 4
Start/Stop State
Output
Direction State
Output
Port Definition:
1# +5V
2# COM
3# COM for external control start/stop
4# External control start/stop: change to high level, start and stop
states switch
5# NC
6# COM for Rs485
7# RS485 B
8# RS485 A
Note: 1 - 3# are RS485 communication bus ports. Can connect to
the control computer (computer, PLC, SCM).
Syringe Selection: The syringe can be selected in the manufacturer
table which includes manufacturer and size
User-defined Syringe: 4 inner diameter of user-defined syringe barrel
canbeinputandsaved
Working Mode Setting: TS-1A has only infusion working mode. TS-
2A/TS-1B has 5 working modes available: infusion, withdrawal,
infusion/withdrawal, withdrawal/infusion, continuous
Parameters Setting: Set dispensing volume, infusion time, withdrawal
time, pause time and copy number
Display Mode Selection: Different parameters (volume, flow rate,
linear speed) can be selected in the main display interface
FastForward&FastReverse:Infusionorwithdrawalatthemax.speed
Calibration: Acquire accurate volume through calibration
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Max. Infusion Distance: 90 mm
AcceptableSyringe:5µL-60mL
Linear Speed: 7.9 µm/min - 79.4 mm/min
Adjusting Resolution: 7.94 µm/min
Distance Resolution: 0.165 µm
Linear Force: 90 N
Setting Mode: Membrane Keypad and rotary coded switch
Accuracy: 0.5% error in the condition
Of 30% of max. Infusion distance
Display: 128x64 graphic LCD
External Control: Input control: start/stop
Output control: start/stop, direction (OC gate)
Communication Interface: RS485
Power:AC100V- 240VorDC12V/3.2A
Power Consumption: 34W
OperatingCondition:Temperature0-40
Relative humidity ‹ 80 %
ControllerDimensions(L×W×H):235×178×74
Controller Weight: 0.9 Kg
DriveUnitDimensions(L×W×H):245×100×95 (mm)
DriveUnitWeight:3Kg
IP Rating: IP41
>
≤
≥
≤
±
℃
23 24
TS-1A/L0107-1A, TS-2A/L0107-2A Specifications TS-1B/W0109-1B Specifications
Max. Infusion Distance: 70 mm
AcceptableGlassSyringe:5µL-1000µL
Linear Speed: 7.94 µm/min - 79.4 mm/min
Adjusting Resolution: 7.94 µm/min
Distance Resolution: 0.165 µm
Linear Force: 20 N
Setting Mode: Membrane Keypad and rotary coded switch
Accuracy: 0.5% error in the condition
of 30% of max. infusion distance
Display: 128x64 graphic LCD
External Control: Input control: start/stop
Output control: start/stop, direction (OC gate)
Communication Interface: RS485
Power:AC100V-240VorDC12V/3.2A
Power Consumption: 24W
OperatingCondition:Temperature0-40
Relative humidity ‹ 80 %
ControllerDimensions(L×W×H):235×178×74
Controller Weight: 0.9 Kg
DriveUnitDimensions(L×W×H):180×46×78(mm)
DriveUnitWeight:0.6Kg
IP Rating: IP21
>
≤±
≥
≤
℃
SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Longer Syringe Pump Operating Manual
TS-1A/L0107-1A
TS-2A/L0107-2A
TS-1B/W0109-1B
Baoding Longer Precision Pump Co., Ltd.
SYRINGE PUMP
OPERATING MANUAL
BaodingLongerPrecisionPumpCo.,Ltd
ADD: Building A,Chuangye Center Baoding
National High - Tech Industrial Development Zone
Baoding, Hebei, China 071051
TEL: 86 - 312 - 3110087 3138553
FAX: 86 - 312 - 3168553
E - mail: [email protected]
Http:www.longerpump.com