Longman 25W*6PCS User manual

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

1
 
19

USER MANUAL
(25W*6PCS,RGBAW 5-IN-1 LED)

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

2
 
19

1. Summariz
Summariz
Thank you for purchasing our Light Please read these instructions carefully before begin and
operate the fixtures according to these instructions to avoid any possible damages and accidents
causes by misusage.
Product introduction
This LED all asher is designed in a fashion of hydrodynamic form. It uses high po er RGBAW
5-in-1 25W COB LED, means each LED is made of R,G,B.A.W five led chips. It performs long
life time, lo po er consumption, high brightness stable capability and colorful. The built-in
program includes dimmer, strobe, ater, gradual change, fading and so on. It has the function of lo
eight, lo po er consumption and stable. International standard DMX 512 signal is requested.
Packing list
LIGHT 1PC
Po er Cable 1Set
DMX Signal cable 1Set
The use manual 1PC
2. Saf ty Information
Saf ty Not s
!
Enquire
the
skilled
people
before
any
repair;
!
Al ays
make
sure
disconnect
from
the
po er
source
before
setting
up,
serving
and
moving;.
!Avoid direct eye exposure to the fixture hen it is on;
Saf ty instruction

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

3
 
19

●Make sure the po er supply voltage are consistent ith this lights，Ensure the use of voltage is in
the range of the request technical parameter.
●before the installation, please check the light’s fasteners and mechanical structure have been
received in good condition and appear no damage.
● This light is designed for indoor or outdoor, orking temperature should be lo er than 50
degree.
●The fixtures should be mounted in any position provided there is adequate room for ventilation.
Make sure there are no inflammable and explosive items (ornaments) in 0.5 meters a ay.
●Yello / green cabling earthling safety; no flicker hen the fixture is orking on.
3. Dim nsion diagram
4. Main Function
Input voltage: AC 100V-264V/47-63HZ
Consume

150W
Lamp Type

25W LED 5-in-1 R

G

B

A

W (6PCS)
Life span: 50000~100000hours

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

4
 
19

PWM Dimmer

1500HZ(16666 grades)
Control Signal

DMX512
Control mode

stand alone/ Master slave mode
Channel

38CH,30CH,23CH,23CH-2,18CH,18CH-2,11CH,6CH,5CH
Function Effect: Smooth dimmer, strobes, gradual change, rainbo effect , autos, auto programming
Built-in temperature control measurement function, hen LED ork overheated, intelligent reduce LED
output po er, current po er output could be checked
Cooling mode: Fan cooling Convection, Fan speed can be set to reduce noise
Beam Angle: 30°,60° Optional
Anti-electricity intension

1.5KV
Insulation Resistance:

M Ω
Size: 512*130*232mm
Net Weight: 5.1 Kg
IP Protection: IP65
5. DMX Control Function
DMX Chann ls

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

5
 
19

Illustrations:The same numbers represent the same group.
38CH 30CH
CHANN
EL NAME
CHANN
EL NAME
1 DIM ALL 1 R1
2 R1 2 G1
3 G1 3 B1
4 B1 4 A1
5 A1 5 W1
6 W1 6 R2
7 R2 7 G2
8 G2 8 B2
9 B2 9 A2
10 A2 10 W2
11 W2 11 R3
12 R3 12 G3
13 G3 13 B3
14 B3 14 A3
15 A3 15 W3

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

6
 
19

16 W3 16 R4
17 R4 17 G4
18 G4 18 B4
19 B4 19 A4
20 A4 20 W4
21 W4 21 R5
22 R5 22 G5
23 G5 23 B5
24 B5 24 A5
25 A5 25 W5
26 W5 26 R6
27 R6 27 G6
28 G6 28 B6
29 B6 29 A6
30 A6 30 W6
31 W6
32 STROBE
33 EFFECT
34 AUTO SPEED
35
VIRTUAL COLOR
WHEEL
36 DIMMER MODE
37 ID FUNCTION
38 ID ADDRESS
23CH 23CH. 18CH 18CH.
CHANN
EL NAME
CHANN
EL NAME
1 DIM ALL 1 DIM ALL
2 R1 2 R1
3 G1 3 G1
4 B1 4 B1
5 A1 5 A1
6 W1 6 W1
7 R2 7 R2
8 G2 8 G2
9 B2 9 B2
10 A2 10 A2
11 W2 11 W2
12 R3 12 STROBE
13 G3 13 EFFECT

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

7
 
19

14 B3 14 AUTO SPEED
15 A3 15
VIRTUAL COLOR
WHEEL
16 W3 16 DIMMER MODE
17 STROBE 17 ID FUNCTION
18 EFFECT 18 ID ADDRESS
19 AUTO SPEED
20
VIRTUAL COLOR
WHEEL
21 DIMMER MODE
22 ID FUNCTION
23 ID ADDRESS
11CH 6CH 5CH
CHANNE
L NAME CHANNEL NAME
CHANNE
L NAME
1 DIM ALL 1
DIM
ALL 1 R
2 R 2 R 2 G
3 G 3 G 3 B
4 B 4 B 4 A
5 A 5 A 5 W
6 W 6 W
7 STROBE
8 EFFECT
9 AUTO SPEED
10
VIRTUAL
COLOR WHEEL
11 DIMMER MODE
NAME VAL
UE FUNCTION
DIM ALL 0-255 DARK->LIGHT
RED 0-255 DARK->LIGHT
GREEN 0-255 DARK->LIGHT
BLUE 0-255 DARK->LIGHT
AMBER 0-255 DARK->LIGHT
WHITE 0-5 DARK->LIGHT

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

8
 
19

STROBE 0-5 No strobe
6-20 Not synchronous strobe(slo to
fast)
21-60 Synchronous strobe(slo to fast)
61-10
0Electronic Sine ave(slo to fast)
101-1
40 Random Strobe(slo to fast)
141-1
80 Opening pulse(slo to fast)
181-2
20 Closing pulse(slo to fast)
221-2
55
Electronic Square ave(slo to
fast)
EFFECT 0-5 NO EFFECT
6-10 CT01(Call custom color CT01)
11-15 CT02
16-20 CT03
21-25 CT04
26-30 CT05
31-35 CT06
36-40 CT07
41-45 CT08
46-50 CT09
51-55 CT10
56-60 AUTO 1(0-255S)
61-65 AUTO 2(0-255S)
66-70 AUTO 3(0-255S)
71-75 AUTO 4(0-255S)
76-80 AUTO 5(0-255S)
81-85 AUTO 6(0-127.5S)
86-90 AUTO 7(0-25.5S)
91-95 AUTO 8(0-12.25S)
96-10
0AUTO 9(0-17S)
101-1
05 AUTO 10(0-25.5S)
106-1
10 AUTO 11(0-25.5S)
111-1
15 AUTO 12(0-25.5S)
116-1
20 AUTO 13(0-17S)

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.

9
 
19

121-1
25 AUTO 14(0-17S)
126-1
30 AUTO 15(0-12.25S)
131-1
35 AUTO 16(0-12.25S)
136-1
40 AUTO 17(0-25S)
141-1
45 AUTO 18(0-25S)
146-1
50 AUTO 19(0-25.5S)
151-1
55 AUTO 20(0-255S)
156-1
60 AUTO 21(0-25.5S)
161-1
65 AUTO 22(0-12.25S)
166-1
70 AUTO 23(0-17S)
171-1
75 AUTO 24(0-25.5S)
176-1
80 AUTO 25(0-25.5S)
181-1
85 AUTO 26(0-25.5S)
186-1
90 AUTO 27(0-17S)
191-1
95 AUTO 28(0-17S)
196-2
00 AUTO 29(0-12.25S)
201-2
05 AUTO 30(0-12.25S)
206-2
10 AUTO 31(0-25S)
211-2
15 AUTO 32(0-25S)
216-2
20 AUTO 33(0-255S)
221-2
25 CHASE1
226-2
30 CHASE2

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
10
! "
19
!
231-2
35 CHASE3
236-2
40
SOUND 1:SOUND CHANGE
COLOR
241-2
45
SOUND 2:SOUND
STROBE(WHITE COLOR
ONLY)
246-2
55 RESERVED
AUTO SPEED 0-255 AUTO SPEED,FAST->SLOW
VIRTUAL
COLOR WHEEL 0-10 No effect
(RGB color
mixing instead of
RGB channels but
A W channels not
affected)
11 Blue (Blue=full,
Red+Green+White=0)(step)
12-50 Red=0, Green->up,Blue =full,
White=0(proportional)
51 Light Blue (Red=0, Green=full,
Blue =full, White=0)(step)
52-90 Red=0, Green=full, Blue->do n,
White=0(proportional)
91 Green (Red=0, Green=full, Blue
=0, White=0)(step)
92-13
0
Red->up, Green=full, Blue=0,
White=0(proportional)
131 Yello (Red=full, Green=full,
Blue=0, White=0)(step)
132-1
70
Red=full, Green->do n, Blue=0,
White=0(proportional)
171 Red(Red=full, Green=0, Blue=0,
White=0)(step)
172-2
10
Red=full, Green=0, Blue->up,
White=0(proportional)
211 Magenta (Red=full, Green=0,
Blue=full, White=0)(step)
212-2
50
Red -> do n, Green=0,
Blue=full, White=0(proportional)

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
#
11
$ %
19
$
251-2
55
Blue (Red=0, Green=0, Blue=full,
White=0)(step)
DIMMER MODE 0-10 Use the dimmer mode hich
menu had set up
11-20 Linear curve and not smooth
21-30 Square la curve and not smooth
31-40 Inverse square la curve and not
smooth
41-50 S-curve and not smooth
51-60 Linear curve and smooth
61-70 Square la curve and smooth
71-80 Inverse square la curve and
smooth
81-90 S-curve and smooth
91-25
5
Use the dimmer mode hich
menu had set up
ID FUNCTION 0-10 ID DISABLE
10-20 ID ENABLE
21-30 ID ADDRESS CHANNEL
DIVIDED BY 10 AND ENABLE
31-25
5RESERVED
ID ADDRESS 0-255 ID ADDRESS
AUTO EFFECT
1 R,G,B,A,W,RG,RB,GB,AW,RGBA,RGBW,RGBAW
2 R↑,R↓,G↑,G↓,B↑,B↓,A↑,A↓,W↑,W↓
3 R↑G↑,R↓G↓,R↑B↑,R↓B↓,B↑G↑,B↓G↓
4 R↑G↑B↑W↑,R↓G↓B↓W↓
5 B,BG↑,BG,B↓G,G,GR↑,GR,G↓R,R,RB↑,RB,R↓B(Rainbo effect)
6 One piece running from 1 to 6 then change color continue
7 2 Amber step running
8 3 Orange running ith fade
9 3 Pink step running
10 2 Red running on Green
11 2 Green running on Blue
12 2 Yello running on Pink
13 1 Red step running
14 1 Yello step running
15 3 Yello running ith fade
16 3 Pink running ith fade

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
&
12
' (
19
'
17 Yello open from 1 to 6 then dark
18 Blue open from 1 to 6 then dark
19 Each piece change ith RGBYPC
20 Inverse direction AUTO 6
21 Inverse direction AUTO 7
22 3 White running ith fade
23 3 Cyan step running
24 Inverse direction AUTO 10
25 Inverse direction AUTO 11
26 Inverse direction AUTO 12
27 Inverse direction AUTO 13
28 Inverse direction AUTO 14
29 Inverse direction AUTO 15
30 Inverse direction AUTO 16
31 Inverse direction AUTO 17
32 Inverse direction AUTO 18
33 Each piece rainbo effect
6. Display Op ration instruction
MENU : access the menu or return to a previous menu option
ENTER: select the current menu option
UP: menu selection or parameter increments
DOWN: menu selection or parameters decrease
M nu Tr :

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
)
13
* +
19
*
TAB LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4
ADDR(Address) 001-512
STAT(Static
control) R1 0-255 *
G1 0-255 *
B1 0-255 *
A1 0-255 *
W1 0-255 *
R2 0-255 *
G2 0-255 *
B2 0-255 *
A2 0-255 *
W2 0-255 *
R3 0-255 *
G3 0-255 *
B3 0-255 *
A3 0-255 *
W3 0-255 *
SHUT 0-255 *
SET(Set) CAL(Calibration) R 0-255
G 0-255
B 0-255
A 0-255
W 0-255
USE YES/NO
CHMD(Channel
mode) 38CH
30CH
23CH
23CH.
18CH
18CH.
11CH
6CH
5CH
DIM(Dimming
mode)
LIN/SQR/ISQR/SC
UR/LIN.
/SQR./ISQR/SCUR.
DISY(Display set) ON(Permanent on)
2MIN (2 minutes
off)
,-./01 2345678
9:;< /7=>
?@ABC-

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
D
14
E F
19
E
CTST(Custom
color set) CT01 R 0-255
. G 0-255
. B 0-255
. A 0-255
. W 0-255
CT10
AUTO(Auto) AT01 RUN.. *
. . RUN.. *
. . RUN.. *
. . RUN.. *
AT33 RUN.. *
ATSP(Auto speed) 0-255
CHS1
G
Chase 1
H
RUN.. *
CHS2
G
Chase 2
H
RUN.. *
CHS3
G
Chase 3
H
RUN.. *
PROG
G
Program
H
CHS1
G
Chase 1
H
SC01
G
Scene 1
H
R1 0-255
. . G1 0-255
. . B1 0-255
. . A1 0-255
. . W1 0-255
. . R2 0-255
. . G2 0-255
. . B2 0-255
. . A2 0-255
. . W2 0-255
. . R3 0-255
. . G3 0-255
. . B3 0-255
. . A3 0-255
. . W3 0-255
. . SHUT 0-255
. . AUTO NONE,AT01-AT33
. . ATSP 0-255(S)
. . TIME 0-255(S)
. . WAIT 0-25.5(S)
. . USE YES/NO
. SC20
G
Scene 20
H
CHS3
G
Chase 3
H
INFO
G
Information
H
SOFT(Soft are
version) Vx.x
POW(Po er
reduction) 100%/80%/50%
IJKLMINOPNQRSTQN UUUV

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
W
15
X Y
19
X
Z
LOAD(Load) ST L
[
Setting load) YES/NO
PR L
[
Program
load) YES/NO
SEND(Send) YES/NO
ID 0-255
Illustrations: When enter to the “*” position displayed on the LED, the projector ill automatically set as master and
send data to external. Other projectors ill synchronously running ithout manually set as slaver. When po er cycle
it ill jump to the “*” position and running again.
6.1 DMX ADDRESS SETTING
1) Press the
\
ENTER
]
button in
\
ADDR
]
menu, then enter to the DMX address setting.
2) Press the
\
UP/DOWN
]
button to select
\
1-512
]
numerical value.
3) Press the
\
ENTER
]
button to escape and save.
6.2 STATIC SETTING
1) Press the
\
ENTER
]
button in
\
STAT
]
menu, then enter to the static setting.
2) Press the
\
UP/DOWN
]
button to select
\
RED1
]^\
GREEN1
]^\
BLUE1
]^\
AMBER1
]
,
\
WHITE1
]
…
\
SHUT
]
.
3) Press the
\
UP/DOWN
]
button to set up the
\
0-255
]
numerical value.
4) Press the
\
ENTER
]
button to escape and save.
6.3 COLOR CAST CALIBRATION SETTING
1) Press the
\
ENTER
]
button in
\
CAL
]
menu, then enter to the color cast calibration setting.
2) Press the
\
UP/DOWN
]
button to select
\
RED
]^\
GREEN
]^\
BLUE
]^\
AMBER
]
,
\
WHITE
]
3) Press the
\
UP/DOWN
]
button to set up the
\
0-255
]
numerical value.
4) On the
\
USE
]
interface, pressing
\
YES
]
button means valid,
\
NO
]
means invalid.
5) Press the
\
ENTER
]
button to escape and save.
Illustrations: When pressing the
\
YES
]
button hich means valid on the
\
USE
]
interface, the actual output value of
RED
^
GREEN
^
BLUE
^
AMBER,WHITE, UV is output in accordance ith the percentage hich the color cast
calibration value divides 255.
6.4 CHANNEL MODE SETTING
1) Press the
\
ENTER
]
button in
\
CHMD
]
menu, then enter to the channel mode setting.

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
_
16
` a
19
`
2) Press the
b
UP/DOWN
c
button to select
b
68CH
cdb
60CH
cdb
28CH
cdb
28CH.
cdb
23CH
cdb
23CH.
cdb
18CH
cd
b
11CH
cdb
6CH
cdb
5CH.
c
3) Press the
b
ENTER
c
button to escape and save.
6.5 DIMMING MODE SETTING
1) Press the
b
ENTER
c
button in
b
DIM
c
menu, then enter to the dimming mode setting.
2) Press the
b
UP/DOWN
c
button to select
b
LIN
cdb
SQR
cdb
ISQR
cdb
SCUR
cdb
LIN.
cdb
SQR.
cdb
ISQR.
c
and
b
SCUR.
c
.
3) Press the
b
ENTER
c
button to escape and save.
Illustrations
e
When setting
b
LIN.
cdb
SQR.
cdb
ISQR.
c
and
b
SCUR.
c
in
b
DIM
c
menu, there ill be added
a little delay dimming effect for smooth..
Dimming curve:
Linear curve: square la curve: Inverse Square la curve: S-curve:
6.6 DISPLAY SETTING
1) Press the
b
ENTER
c
button in
b
DISY
c
menu, then enter to the display setting.
2) Press the
b
UP/DOWN
c
button to select
b
ON
cdb
2 MINITES OFF
c
3) Press the
b
ENTER
c
button to escape and save.
6.7 UTO LOCK KEY SETTING
1) Press the
b
ENTER
c
button in
b
LOCK
c
menu, then enter auto lock key setting.
2) Press the
b
P/DOWN
c
button to select
b
YES
c
,
b
NO
c
3) Press the
b
ENTER
c
button to escape and save.
Instructions:
When set to [YES], it will lock automatically after two minutes to prevent accidental triggering flood flushing,
and then press any key for 10 seconds to unlock.
6.8 CUSTOM COLOR SETTING

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
f
17
g h
19
g
1) Press the
i
ENTER
j
button in
i
CTST
j
menu, then enter to the custom color setting.
2) Press the
i
UP/DOWN
j
select
i
CT01
j
…
i
CT10
j
2) Press the
i
UP/DOWN
j
button to select
i
1-512
j
numerical value.
3) Press the
i
ENTER
j
button to escape and save.
6.9 AUTO RUN, SELF-PROGRAM RUN
1)Press the
i
ENTER
j
button in
i
AUTO
j
menu, then enter to the auto run,self-program run.
2)Press the
i
UP/DOWN
j
button to select
i
AT01
j
…
i
AT33
jki
SPEED
jki
CHASE01
j
…
i
SOUND2
j
3)Press the
i
ENTER
j
button to start running.
6.10 EDIT SELF-PROGRAM
1) Press the
i
ENTER
j
button in
i
PROG
j
menu, then enter to the edit self-program.
2) Press the
i
UP/DOWN
j
button to select
i
CHASE01
j
…
i
CHASE03
j
3) Press the
i
ENTER
j
button for confirmation and enter to the next menu.
4) Press the
i
UP/DOWN
j
button to select
i
SCENE01
j
…
i
SCENE20
j
5) Press the
i
ENTER
j
button for confirmation and enter to the next menu.
6) Then press the
i
UP/DOWN
j
button to select
i
RED1
j
…
i
SHUT
jki
TIME
jki
WAIT
jki
USE
j
7) Press the
i
UP/DOWN
j
button to set up the parameter hich are needed.
8) Press the
i
ENTER
j
button t o escape and save.
Illustrations
l
When
i
USE
j
is set to be
i
NO
jk
or the parameter of
i
TIME
j
is 0, it ill not run this scene.When
i
WAIT
j
is set to be FADE time, the running process is as the follo ing chart sho ing.
6.11 CHECK THE LIGHTING INFORMATION
1) Press the
i
ENTER
j
button in
i
INFO
j
menu, then enter to the checking the lighting information.
2)
i
SOFT
j
button is for soft are version information.
3)
i
POW
j
button is for the current information of po er reduction. It is 100% output in normal conditions, but 80%
or 50% output in over temperature protection situation.

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
m
18
n o
19
n
6.12 LIGHTING SETTING PARAMETER RESET
1) Press the
p
ENTER
q
button in
p
ST L
q
menu, then enter to the lighting setting parameter reset.
2) Press the
p
UP/DOWN
q
button to select
p
YES
q
.
3) Press the
p
ENTER
q
button to escape and save.
Illustrations
r
“ADDR” “CTST” and “PROG” are not reset, the others reset to the underlined value of the ord.
6.13 【PROG】SELF-PROGRAMMING PARAMETER RESET
1) Press the
p
ENTER
q
button in
p
PR L
q
menu, then enter to the
p
PROG
q
self-programming parameter reset.
2) Press the
p
UP/DOWN
q
button to select
p
YES
q
.
3) Press the
p
ENTER
q
button to escape and save.
6.14 LIGHTING PARAMETER DOWNLOADING EACH OTHER VIA DMX
CABLE
1) Press the
p
ENTER
q
button in
p
SEND
q
menu, then enter to sending parameter to other lights.
2) Press the
p
UP/DOWN
q
button to select
p
YES
q
.
3) Press the
p
ENTER
q
button to confirm sending.
Illustrations
r
1)Please disconnect the connection of projector and DMX console before sending the parameter.
2)The information of
p
ADDR
qsp
CAL
qsp
ID
q
can’t be sent, can’t be do nloaded each other.
3)There ill be an automatic reset of the other projectors after receiving parameter
correctly.
6.15 ID ADDRESS SETTING
1) Press the
p
ENTER
q
button in
p
ID
q
menu, then enter to the ID address setting.
2) Press the
p
UP/DOWN
q
button to select
p
0-255
q
numerical value.
3) Press the
p
ENTER
q
button to escape and save.
Illustrations
r
1)When ID FUNCTION in channel profile is 10-20,the ID ADDRESS in fixture setting must equal to the ID
ADDRESS in channel profile setting then the fixture ill be actived.
2)When ID FUNCTION in channel profile is 21-30,the ID ADDRESS in channel profile setting ill be divided by
10 then ignore the fractional part, if the result is equal to the ID ADDRESS hich setted in
p
ID
q
menu,the fixture

广州朗文光电有限公司
GUANGZHOU LONGMAN PRO LIGHT FACTORY CO,. LTD.
t
19
u v
19
u
ill be actived.For example, if the fixture ID ADDRESS is 3 no ,the valid value in the channel profile setting is
30-39. Similarly hen 15 the valid value is 150-159.
7、TROUBLESHOOTING
PROBLEM REASON AND ACTION
The light can’t be
started normally
Check the po er connection is correct or not.
Please detect the voltage.
Po er supply is damaged or incorrect connected. Call a
qualified personnel to fix it.
Connection of control board is not correct. Call a qualified
personnel to fix it.
Out of console’s
control
Please check the DMX connector and the po er
connection is connected correctly or not. It means having
signal if it sho s t inkling of the decimal point hich in
the lo er right corner of the screen hen exiting the screen
saver.
Please check the DMX address setting of lighting is correct
or not.
Check【CHMD】setting is correct or not.
Please check hether the DMX line is near to the high
voltage ire or not. In that case, it ill damage or interfere
the DMX electric circuit.
The beam appears
dim ,the brightness
declines obviously
Check hether the 【CAL】is started or not and the set value
is too small.
Check hether the【POW】is in over temperature protection
situation or not, if yes, please take measures for ventilation.