Loopcomm LP-8696P User manual

http://www.loopcomm.com
Step1
Step3
Step4
Step8
Step9
http://setup.loopcomm.com
Step2
Step5
Step6
Step7
SMART REPEATER
SmartRepeater
Loopcomm_Repeater loopcomm
Side and Bottom Panel Description
Antenna : Two 2dBi fix external Antenna.
Connect the Cable RJ-45 to Smart Repeater
and to computer or Notebook Port
Plug the Smart Repeater to Power Plug
1.Click on the wireless icon to see available wireless networks
(For vista, click start> Connect To)
2.Select your current Wireless Network and click Disconnect
3.Press WPS button for 5Seconds to restart the Smart Repeater
and wait for 60Seconds and try
http://setup.loopcomm.com again.
Find an optimal setup location between your Wireless Router and
your wireless dead zone
Normal Power 100mW Compact Wi-Fi Range Extender
LP-8696P
Indoor 802.11B/G/N 2.4G Wireless Smart Repeater
READ FIRST
Quick Install Guide 1.0.0
Connect your PC or Tablet to the Smart Repeater
Open your Web Browser
Enter the setup web address into your browser:
If the URL fails to open, then try http://192.168.1.250
Recommended browsers: Google Chrome, Safari or Internet Explorer (8.0 or up) Do not use Firefox
Disconnect your PC from wireless networks, open your browser and try again.
Windows 7 & Vista (example)
Welcome to Dashboard
Scan for a wireless Network
The Dashboard will provide you with the current
status of the Smart Repeater.
Click Scan to find available networks to extend
Click Scan to begin scanning for nearby wireless
networks.
Highlight and select the wireless network(S) that
you wish to repeat.
Recommended signal
Select the wireless network with
a signal strength greater than 70%
for the most reliable connection
Click Next to Continue.
Home Network Security Settings (If necessary)
Enter your password and then click next.
If your wireless home network(s) does not have
security enabled, leave the security field blank.
Click Next to Continue.
Configure Settings for your Extended Network
The ID of your extended network is:
Loopcomm_Repeater
To change it, enter a new name in the SSID Field.
Wireless Users connecting to the range extender
can use this ID to identify the extended network.
Enter a new key in the security key field. The key
must be at least 8 characters long.
Click Next to apply your settings. The smart Repeater
will reboot. This process may take up to 150seconds.
Don’t refresh the web page.
The page will automatically reload with the connection
status.
Connect to the New Extended Network
During the countdown process, the Range extender
will reboot and disconnect the Wi-Fi connection. At
this point, you need to reconnect your PC or tablet to
the new extended network. Follow the instruction on
the screen to connect to the extended network.
Once you have connected, click the check box to
confirm.The Next button will appear allowing you to
complete the setup process.
If there are problems with your configuration, the
setup wizard will inform you to rescan for a network
to extend.
If there are no problems, you will see the setup
summary page below.
Congratulations, the smart repeater is now
successfully configured. Your settings are now
saved. You may now detach the Ethernet cable
from your computer and connect to wireless
smart repeater.
You may also attach any wired network
devices to the wired ports on the back
of the smart repeater.
Press Finish to complete the process.
If there is a problem with your configuration,
then the smart setup wizard will inform you to
restart the wizard and select another network
to repeat.
Setup Summary
Finish Refesh
Press 3Seconds for
WPS configuration
Press above 5Seconds
to reset
RJ-45 Port for connecting
to computer
Power Plug

http://www.loopcomm.com
Loopcomm_Repeater
Loopcomm_Repeater
Loopcomm_Repeater
Smart Features
Access Schedule
How to Connect your Wireless Computer to the Smart Repeater
Windows 7 and Vista Windows 8
IPhone
Click on the wireless icon to see available wireless
Networks (For Vista, Click Start > Connect To).
Select the “Loopcomm_Repeater” network and
click Connect.
Swipe in from the right edge to access the
Charms bar, tap on Settings, Select the
WiFi icon and select “Loopcomm_Repeater”
A. Click on the wireless icon to view available wireless
networks. Select the “Loopcomm_Repeater” or
network to join that network.
Tap on settings icon, select Wi-fi, and
choose the network,”Loopcomm_Repeater”.
MAC OS X
Wi-Fi Protected Setup (One-Touch Setup or Push Button Configuration)
If your wireless adapter has WPS one touch setup, you can use it when connecting to the Smart Repeater,
Hold the WPS button on the smart Repeater (left side) for 3 seconds. The WPS LED will begin to blink. As it
blinks push the WPS button on your wireless adapter or enable WPS with the provided software for your
wireless adapter.
Using the Smart Features on your Smart Repeater
The Smart Repeater is equipped with many powerful security features which can be accessed through
the web menu:
Access Scheduling
Control when your Wi-Fi is on/off
2.4GHz Wi-Fi settings > Access Schedule
User Access Control
Restrict network access to specific users
2.4GHz Wi-Fi settings > Access Schedule
Wireless Coverage Control
Adjust the distance of your wireless network
2.4GHz Wi-Fi settings > Access Schedule
Setting the Range Extender’s System Clock
In order to access schedules and perform the logs using the correct time stamps and schedules you
need to set your System clock. To do so, Press Management and access the System clock, tab to sync the
System Clock with your computer time.
Tips: Trouble Accessing the smart setup Wizard
PROBLEM: The setup wizard does not appear when you enter the setup web address.
http://setup.loopcomm.com
Enter the setup web address into your browser:
If the URL fails to open, then try http://192.168.1.250
Solution: Disconnect your computer from all Wi-Fi networks and try again
Your computer should be connected to the Dual Band Range Extender with the included Ethernet Cable.
Disconnect your computer from all
wireless networks .
Enter http://setup.loopcomm.com into
your web browser again.
NOTE : your computer does not need internet to access the Smart Setup Wizard.
Click the wireless signal icon from bottom
Right corner. Select your network and click
Disconnect.
Right click the wireless signal icon from bottom right corner.
Click view available wireless networks, select your network and
click Disconnect.
Check your power first
Reboot the smart Repeater. Disconnect your computer from all wireless networks and try again.
Tips: Power Outages, Resetting Routers and Channel Changes
Wireless routers operate on specific wireless channels to avoid interference with neighboring networks. Some
wireless routers are set automatically to scan for the best wireless channel. A power outage, or a simple reboot,
may cause your home wireless router to change its wireless channel and cause the range extender to disconnect
from your home network.
To fix this issue, Simply log onto the smart repeaters web menu by opening your web browser and accessing
http://setup.loopcomm.com. If the page does not load, try resetting the smart repeater by holding the reset
button for 5 to 10seconds. After the Smart Repeater has rebooted open your web browser and try again.
When the web menu appears, run through the smart setup wizard again to reconfigure the connection to your
home network.
To prevent the channel changing issue from occurring in the future, you may log onto your router’s web menu
and set the wireless channel from automatic to a static channel number. You need to reconfigure the smart
repeater with the new channel. If you are not sure how to access your router’s web menu, contact the support
department for the brand of your wireless router.
Auto loading web menu
When the smart repeater loses its connection with your home network, the web menu will automatically load on
your web browser. All web address entries will be redirected to the smart setup wizard of the smart repeater. This
redirect feature is through the web menu (left side): More Settings>2.4G> Network Settings> IP Settings
Trouble Shooting Tips
PROBLEM: I cannot connect to my home network. I received an error when running the smart setup wizard.
SOLUTION: a. Your home network may be secured. Double check that you have the correct security
key to connect to the home network.
b. Reboot your home network router and try to connect again using the smart setup wizard.
c. Check that your home network router’s DHCP server is enabled. The smart repeater needs
to obtain an IP from your home network router.
PROBLEM: My smart repeater was working fine previously, but now I can no longer access the internet
through the smart repeater.
SOLUTION : a. The connection to your home network may have been dropped or the router settings
may have changed. Changes to the router could be a result of several events, such as
power outage. When this occurs, connect to the smart repeater and access the setup
menu using the web address: http://setup.loopcomm.com
Run the smart setup wizard to reconnect the smart Repeater to your network.
b. The smart repeater may be too far from your home router are not maintaining signal
Strength above 70%. Check the signal strength between the router and the smart
Repeater through the web menu (left side): more settings>Management>device status.
The signal strength readout will be under the home wireless network settings section.
This signal strength must be above 70%. If it is below, move the smart repeater closer to
your router, or reposition the smart repeater.
PROBLEM: I cannot find my home network when scanning for wireless networks in the smart setup wizard.
SOLUTION: a. The smart repeater may be out of range, Move the smart repeater closer towards the
wireless router and try the setup wizard again from the web menu.
b. Make sure that your home networks wireless SSID is broadcasting and not hidden.
Hidden SSIDs will require that you manually enter the SSID into the wireless settings
>2.4G > home network menu.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.